Manual Operation
To cook food using a specic entered time and power level.
1. Open oven door and place food in oven. Close door.
2. Press TIME ENTRY pad and enter cooking time.
3. Press POWER LEVEL pad to change power level if desired.
• For a lower microwave power, press pads 1 (for 10%) through 9 (for
90%).
4. If stage cooking is desired, press STAGE pad and repeat steps 2 through 4.
5. Press START pad.
6. At end of cooking cycle oven beeps and shuts off.DONE displays.
Programming Pads
1. READY must be in the display. If not, open and close door.
2. Press PROGRAM SAVE pad.
• Programming mode begins.
• Enter Program to Add/Review: displays.
3. Press pad to be programmed or reprogrammed.
• Display will change to review all settings for the pad.
• The pad number that is being programmed displays beside the word
ITEM.
4. Press TIME ENTRY to program amount of cooking time.
• Enter desired cooking time by using numeric key pads.
• Maximum cooking time is 60 minutes.
5. Press POWER LEVEL to program level of microwave power.
• Press numeric key pad for desired level. Press numeric key pad again
to set power level to 100%.
• For a lower microwave power, press pads 1 (for 10%) through 9 (for
90%).
6. Press Quantity pad if different cooking factor is desired.
• Default of CF:80 displays.
• Enter desired cooking factor by using numeric key pads (1 for 10%
through 0 for 100%).
7. Press PROGRAM SAVE to save the program changes.
8. To discard changes, press STOP/RESET.
Mid-Cycle Pause
To add a pause to a programmed
cooking cycle:
1. Press HIDDEN PAD after
entering time or power level.
2. A short beep sounds. This
indicates the program is set for a
mid-cycle pause.
3. Continue programming pad as
desired.
When programmed pad is used,
pause will occur in the middle of total
programmed time. Oven will beep
continuously and Program Paused
displays until door is open and shut.
To continue cycle, press START pad.
CLEAN FILTER
This oven displays CLEAN FILTER
at user dened intervals. When the
message displays ACP recommends
cleaning the air lter thoroughly.
Cleaning the air lter will not shut
off the message. The message will
stop displaying automatically after
24 hours. Depending on microwave
use and environmental conditions,
the lter may need to be cleaned
more frequently. Once the frequency
is determined, set the option for the
appropriate time frame.
So...how do I use it?
Preprogrammed
Pads
To cook food using
preprogrammed cooking
sequences.
1. Open oven door and place food
in oven. Close door.
• To add additional servings
press QUANTITY pad.
• Up to eight quantities can be
added.
2. Press desired pad.
3. Oven begins to cook.
4. At end of cooking cycle oven
beeps and shuts off. DONE
displays.
Oven Clearances
A—For North American (UL/CSA) models, allow at
least 2” (5.1 cm) of clearance around top of oven.
For International (50 Hz) models, allow at least 7”
(17.8 cm) of clearance around top of oven. Proper air
ow around oven cools electrical components. With
restricted air ow, oven may not operate properly and
life of electrical parts is reduced.
B—Allow at least 2
9
/16” (6.5 cm) between air
discharge on back of oven and back wall.
C—Allow at least 2” (5.1 cm) around sides of oven.
Refer to Product Safety Manual for Safety Statements
Complete Owner’s Manual available online
Quick Start Reference Guide
2009 ACP, Inc.
Cedar Rapids, Iowa 52404
Part No.20001402
Printed in U.S.A. 11/09
For full product documentation visit:
www.acpsolutions.com
Changing user
options
Options such as single or
double pad programming and
beep volume can be changed to
suit individual preferences.
To change options:
1. Press hidden pad.
• Pad is unmarked.
• The display remains blank when hidden pad is pressed.
2. Press PROGRAM SAVE pad.
• The rst user option will display. Oven is now in options mode.
3. Press number pad that controls option to be changed.
• See table below for options.
• Current option will display.
4. Press number pad again to change the option.
• Each time pad is pressed, option will change.
• Match code displayed with code for desired option.
• Changes take affect after pad is pressed.
• To change additional options, repeat steps 3 and 4.
5. Press PROGRAM SAVE to return to READY, or open and close oven
door.
HIDDEN
PAD
No popcorn
No metal pans
DO NOT power spray
Numbered Pads Displays Options
1
Double Digit Entry
Disabled
Enabled
Allows 10 (0-9) preprogrammed pads.
Allows 100 (00-99) preprogrammed pads.
2
Manual Programming
Disabled
Enabled
Manual time entry/cooking not allowed
Manual time entry/cooking allowed
3
Reset on Door Open
Disabled
Enabled
Opening oven door does not reset oven back to ready
Opening oven door resets the oven back to ready mode
4
Keybeep
OFF
ON
Keys do not beep when pressed (keybeep off)
Keys beep when pressed (keybeep on)
5
Speaker Volume
OFF
LOW
MEDIUM
HIGH
Keybeep volume OFF
Keybeep volume LOW
Keybeep volume MEDIUM
Keybeep volume HIGH
6
End of Cook Signal
Solid Beep
3 Second Beep
4 Beeps Once
4 Beeps Repeating
Food done signal is a continuous beep until reset by user
Food done signal is a three second beep
Food done signal is four beeps continously
Food done signal is four beeps, four times
7
Keypad Active
15 Seconds
30 Seconds
60 Seconds
120 Seconds
Always
Keypad time entry window is 15 seconds
Keypad time entry window is 30 seconds
Keypad time entry window is one minute
Keypad time entry window is two minutes
Keypad time entry window is always active
Stage Pad
Clean Filter Message
(Frequency)
Disabled
Weekly
Monthly
Quarterly
Oven will not display Clean Filter
Oven will display Clean Filter every seven (7) days
Oven will display Clean Filter every thirty (30) days
Oven will display Clean Filter every ninety (90) days
Refer to Product Safety Manual for Safety Statements
Complete Owner’s Manual available online
Quick Start Reference Guide
/
