Vortex Strike Eagle®1-6x24 User manual

Vortex
Brand
Vortex
Model
Strike Eagle®1-6x24
Type
User manual

This manual is also suitable for

1-6x24 and 1-8x24 RIFLESCOPES
STRIKE EAGLE
®
PRODUCT MANUAL
3 2
STRIKE EAGLE
®
RIFLESCOPE
Strike Eagle
®
Riflescope
Speed and versatility—that’s what 1x variable optics offer
AR shooters who need to engage targets from point-blank
out to extended range, and that’s exactly what you get with
the redesigned Strike Eagle
®
. Plus, with an updated reticle
and a screw-in throw lever, you’ll be on target even faster.
Thread-In
Throw Lever
Elevation Turret
Windage Turret
Illumination Dial
Magnification Adjustment Ring
Fast Focus
Eyepiece
Ocular Lens
Objective Lens
1-6x24 1-8x24
WATERPROOF
IPX7 IPX7
FOGPROOF
Nitrogen Gas Purged Nitrogen Gas Purged
LENGTH
10.5" (266.7mm) 10" (254mm)
MOUNTING LENGTH
6.6" (167.6mm) 6.4" (162.6mm)
WEIGHT
18.5 oz. (524.5 g) 17.6 oz. (499 g)
EYE RELIEF
3.5" (89mm) 3.5" (89mm)
FIELD OF VIEW
1x mag: 116.6ft @ 100yds (22°) 1x mag: 109ft @ 100yds (20.6°)
6x mag: 19.2ft @ 100yds (3.76°) 8x mag: 14.4ft @ 100yds (2.75°)
BATTERY
CR2032 CR2032
STRIKE EAGLE
®
MODELS MOA
ADJUSTMENT GRADUATION
1/2 MOA
ELEVATION ADJUSTMENT
140 MOA
WINDAGE ADJUSTMENT
140 MOA
TRAVEL PER ROTATION
44 MOA
Rear Mounting Length
2.1" / 53.3mm
Eyepiece
3.9" / 99mm
1.7" /
43.2mm
1.18" /
30mm
Tube
Diameter
Eyepiece
Diameter
Front Mounting Length
2.9" / 73.7mm
10.5" / 266.7mm
1-6x24
Rear Mounting Length
1.8" / 45.7mm
Eyepiece
3.5" / 89mm
1.7" /
43.2mm
1.18" /
30mm
Tube
Diameter
Eyepiece
Diameter
Front Mounting Length
2.8" / 71.1mm
10" / 254mm
1-8x24
Images are for representation only. Product may vary slightly from what is shown.
5 4
STRIKE EAGLE
®
RIFLESCOPE
UNDERSTANDING THE RIFLESCOPE
Reticle Focal Plane
All riflescope reticles are either First Focal Plane (FFP) or
Second Focal Plane (SFP), depending on the reticle’s location
within the riflescope. This riflescope features a SFP reticle.
Second Focal Plane Reticles
SFP reticles are located near the scope’s eyepiece behind
the image erecting and magnifying lenses. This style of
reticle does not visually change in size when you change
the magnification. The advantage of an SFP reticle is that it
always maintains the same ideally-sized appearance when
shooting. Be aware that the listed reticle subtensions used
for estimating range, holdover, and wind drift correction are
only accurate at the highest magnification.
Ocular Focus
The ocular focus is essentially a one-time adjustment
used to focus the reticle for maximum sharpness. This
adjustment is slightly different for every shooter. A clearly
focused reticle is a critical component for accurate shooting.
Ocular Focus—Reticle Focus Adjustment
Your riflescope uses a fast focus eyepiece designed to
quickly and easily adjust the focus on the riflescope’s
reticle. To adjust the reticle focus:
1. Look through the riflescope
at a blank white wall or up
at the sky.
2. Turn focus knob
fully outward
(counterclockwise).
3. Slowly turn the eyepiece focus knob inward until the
reticle image is as crisp as possible.
TIP: Make this adjustment by taking short, quick glances
through the scope as your eye will try to compensate for
an out-of-focus reticle.
WARNING: Looking directly at the sun through a
riflescope, or any optical instrument, can cause severe
and permanent damage to your eyesight.
Magnification
The magnification adjustment is
used to change the riflescope’s
magnification level, or “power,”
adjusting from low to high
magnification depending on the
shooter’s preference.
Magnification Adjustment
Rotate the magnification ring to the desired magnification.
7 6
STRIKE EAGLE
®
RIFLESCOPE
Throw Lever Installation
Thread in the included throw
lever as shown until the throw
lever is secured.
Arc Measurements
This scope uses Minute of Angle (MOA) arc measurements.
Minute of Angle (MOA) arc measurements are based on the
concept of degrees and minutes in a circle. There are 360°
in a circle, and 60 minutes in a degree. One MOA will
always subtend 1.05” for each 100 yds. of distance. In
other words, if a rifle and scope were zeroed at 100 yds.
and the target is moved out to 200 yds., the bullet’s impact
will be 1.05” (1 MOA) lower on the target at 200 yds. Most
riflescopes using MOA turrets will adjust in 1/4-minute
increments. Adjustments can be felt by mechanical “clicks,”
which subtend .26” for each 100 yds. of distance.
Note: These measurements are often rounded down to 1
MOA equaling 1 inch at 100 yards, and each adjustment
(each mechanical click) equaling 1/4 inch at 100 yards.
Bullet Drop
1 Degree
60 Minutes-of-Angle
(MOA)
MOA
Turrets
Use turrets to adjust the bullet’s point-of-impact. There are
two turrets on your riflescope. The turret on the top of the
riflescope is the Elevation Turret and is used to adjust the
point-of-impact up and down. The turret on the right-hand
side of the riflescope is the Windage Turret and is used to
adjust the point-of-impact left and right. Vortex
®
riflescopes
incorporate precision, finger adjustable Elevation and
Windage Turrets with audible and tactile clicks.
Elevation Turret
Windage Turret
MOA Models
1 Click = 0.5 MOA
Turret Adjustments
Your riflescope features adjustable elevation and windage
turret dials with audible and tactile clicks. Each click
moves the bullet’s point of impact 1/2 MOA.
To make turret adjustments:
1. Remove the turret caps.
2. Following the directional arrows, turn the dials in the
direction you wish the bullet’s point of impact to go.
3. When finished adjusting, replace the turret caps.
9 8
STRIKE EAGLE
®
RIFLESCOPE
Image Sharpness—Parallax
Your scope comes equipped with a fixed parallax setting.
The parallax is set for 100 yards.
Battery Installation/Replacement
To install/change the battery, unscrew the illumination
dial’s outer cap. Install a new CR2032 battery with
numbers facing out.
A spare battery may be stored inside the
windage cap, if desired, as shown here.
Replacing the Battery:
1. Unscrew the outer
cap with a coin.
2. Remove the
CR2032 battery.
3. Replace with a new
CR2032 battery with
the + side facing out.
Illumination – Side Illumination Control
Your riflescope uses a variable intensity reticle
illumination system to aid in low-light performance.
A rotary dial is mounted on the left-hand side of the
riflescope for easy access.
To activate/adjust the illumination,
rotate the adjustment dial in
either direction. The illumination
dial allows for 11 levels of
illumination intensity.
Battery Cap
RIFLESCOPE MOUNTING
To get the best performance from your Vortex
®
riflescope,
proper mounting is essential. Although not difficult, you
must follow the correct steps. Please follow the instructions
below for the proper scope mounting procedure, or go to
vortexoptics.com for a video tutorial.
If you are unsure of your abilities, use the services of a
qualified gunsmith.
Riflescope Mounting Checklist
; Gun vise or a solid platform/rest for your rifle
; Scope rings
; Torque wrench
; Reticle leveling tool, feeler gauges, or weight on a rope
Recommendation: Pick up the
Vortex Torque Wrench Mounting
Kit, which comes with the
complete set of bits needed to
install Vortex
®
scopes and rings!
Rings and Bases
Your Vortex
®
riflescope features a 30mm main tube. Be sure
to select a base, and matching rings appropriate for your rifle,
and mount according to the manufacturer’s instructions.
Note: Vortex
®
Optics recommends not exceeding 18 in./lbs.
(inch/pounds) of torque on the ring screws.
11 10
STRIKE EAGLE
®
RIFLESCOPE
Eye Relief and Reticle Alignment
After installing the bottom ring halves on the mounting
base, place the riflescope on the bottom ring halves and
loosely install the upper ring halves. Before tightening the
scope ring screws, adjust for maximum eye relief to avoid
injury from recoil:
1. Set the riflescope to its highest magnification.
2. Ensure the riflescope is centered in the rings.
3. While viewing through the riflescope in a normal shooting
position, slowly slide the riflescope back toward your
face. Pay attention to the field of view. Stop sliding the
riflescope back as soon as you see the full field of view.
4. Without disturbing the front-back placement, rotate the
riflescope until the vertical crosshair exactly matches
the vertical axis of the rifle.
NOTE: Using a reticle leveling tool, a plumb bob, a
bubble level, or an adjustable set of feeler gauges placed
between a one-piece base and the flat bottom of the
riflescope’s center section will help with this procedure.
5. After aligning the reticle, tighten and torque the ring
screws down per the manufacturer’s instructions. Use
caution and do not overtighten.
Bore Sighting
Initial bore sighting will save time and money at the range.
Do this by using a mechanical or laser bore sight according
to the manufacturer’s instructions, or by removing the bolt and
sighting through the barrel on some rifles.
To Visually Bore Sight a Rifle:
1. Place the rifle solidly on a rest and remove the bolt.
2. Sight through the bore at a target approximately 100
yards away.
3. Move the rifle and rest until the target is visually
centered inside the barrel.
4. With the target centered in the bore, make windage and
elevation adjustments until the reticle crosshair is also
centered over the target.
Final Range Sight-In
After the riflescope has been bore-sighted, final sight-in
should be done at the range using the exact ammunition
you expect to use while hunting or shooting competitively.
Sight-in and zero the riflescope at the preferred distance.
100 yards is the most common zero distance, although you
may prefer a 200-yard zero for long-range applications.
1. Following all safe shooting practices, fire a three-shot
group as precisely as possible.
2. Next, adjust the reticle to match the approximate center
of the shot group. Be sure to read pages 12–13 prior to
making adjustments.
NOTE: If the rifle is very solidly mounted and cannot be
moved, simply look through the scope and adjust the
reticle until it is centered on the fired group.
13 12
STRIKE EAGLE
®
RIFLESCOPE
3. Carefully fire another three-shot group and see if the
bullet group is centered on the bullseye. This procedure
can be repeated as many times as necessary to achieve
a perfect zero.
Indexing the Elevation and Windage Turrets
Strike Eagle
®
riflescopes feature Elevation and Windage
Turrets that allow you to re-index the zero indicator after
sight-in without disturbing your zero setting. Though not
a required process, re-indexing the turrets allows you to
quickly return to your original zero setting if you dial
temporary corrections in the field.
To Index the Turrets:
1. After completing the final sight-in, remove the
turret cap(s).
2. Without rotating the turret, twist the dial to reposition it
with the “0” mark aligned with “Up” on
the scope housing.
3. Replace the turret cap(s).
MAINTENANCE
Cleaning
The Strike Eagle
®
riflescope requires very little routine
maintenance other than periodically cleaning the exterior
lenses. The scope’s exterior may be cleaned by wiping with
a soft, dry cloth. When cleaning the lenses, be sure to use
products that are specifically designed for use on coated
optical lenses.
• Be sure to blow away any dust or grit on the lenses prior
to wiping the surfaces.
• Using your breath, or a very small amount of water or
pure alcohol, can help remove stubborn things like dried
water spots.
Lubrication
All Strike Eagle
®
components are permanently lubricated, so
no additional lubricant should be applied. If possible, avoid
exposing your riflescope to direct sunlight or any very hot
location for long periods of time.
Note: Other than to remove the turret caps and battery
cap, do not attempt to disassemble any components of the
riflescope. Disassembling of riflescope may void warranty.
15 14
STRIKE EAGLE
®
RIFLESCOPE
TROUBLESHOOTING
Please check the following items prior to returning a
riflescope for service.
Sighting-In Problems
Many times, problems thought to be with the scope are
actually mounting problems. Be sure the mounts are
properly torqued to the rifle and the scope is secured so it
doesn’t twist or move in the rings. An insufficient windage
or elevation adjustment range may indicate problems with
the base mount, base mount holes drilled in the rifle’s
receiver, or barrel/receiver alignment.
Grouping Problems
There are many issues that can cause poor bullet grouping.
• Be sure that rings are correctly torqued to 15-18 in/lbs.
• Be sure that all screws on rifle’s action are
properly tightened.
• Be sure rifle barrel and action are clean and free of
excessive oil or copper fouling.
• Maintain a good shooting technique and use a solid rest.
• Some rifles and ammunition don’t work well together—
try different ammunition and see if accuracy improves.
Common Problems
Point of Impact Changes Drastically After Turret Adjustment
• Verify that the ring screws are not over torqued. Ring
screws should only be torqued to 18 in/lbs, and no
thread locking component applied. Over torqueing the
ring screws will cause excess pressure on the tube,
which will cause problems when adjusting the reticle.
Point of Impact is Inconsistent
• Ensure the cantilever mount/rings are mounted only
to the receiver. The cantilever mount/rings need to
be mounted to one, solid surface. Make sure that the
forward connection of the cantilever mount, or ring, is
not mounted to the fore end of the rifle.
• Verify that the ring screws are not over torqued. Ring
screws should only be torqued to 18 in/lbs, and no
thread locking component applied. Over torqueing the
ring screws will cause excess pressure on the tube,
which will cause problems when adjusting the reticle.
Insufficient Adjustment Ranges
• Check that you have the proper base and rings for your rifle
and for your size. If you need assistance, contact a local
gunsmith to be properly fitted to your rifle and scope.
• Once you have verified that you have the correct base and
mounts, and that you have been properly fitted to your gun,
make sure you followed the correct mounting procedure.
See Riflescope Mounting section for this procedure.
Reticle Appears to Come In and Out of Focus
• Check and reset the ocular focus of the reticle for the
shooter’s eye. See Riflescope Adjustments section,
Ocular Focus – Reticle Focus Adjustment.
17 16
STRIKE EAGLE
®
RIFLESCOPE
VIP WARRANTY
OUR UNCONDITIONAL PROMISE TO YOU.
Learn more at VortexOptics.com
service@VortexOptics.com • 800-426-0048
NOTE: The VIP Warranty does not cover loss, theft, deliberate
damage, or cosmetic damage not affecting product performance.
We promise to repair or replace
the product. Absolutely free.
Unlimited.
Unconditional.
Lifetime Warranty.
19 18
STRIKE EAGLE
®
RIFLESCOPE
M-00280-0
© 2020 Vortex Optics
® Registered Trademark and TM Trademark of Vortex Optics
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Vortex Strike Eagle®1-6x24 User manual

Vortex
Brand
Vortex
Model
Strike Eagle®1-6x24
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents