JET HBS-814GH Owner's manual

Brand: JET

Model: HBS-814GH

Type: Owner's manual

Operating Instructions and Parts Manual

Geared Head Horizontal Band Saw

Model HBS-814GH

JET

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-414466

Ph.: 800-274-6848 Revision C1 09/2018

This .pdf document is bookmarked

Warranty and Service

JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please

contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.

Warranty Period

The general warranty lasts for the time period specified in the literature included with your product or on the official

JET branded website.

• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)

• Accessories carry a limited warranty of one year from the date of receipt.

• Consumable items are defined as expendable parts or accessories expected to become inoperable within a

reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from the date of delivery.

What is Covered

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty

does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear,

improper repair, alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood.

Use of these machines in the processing of metal, plastics, or other materials outside recommended guidelines may

void the warranty. The exceptions are acrylics and other natural items that are made specifically for wood turning.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a

Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

How to Get Technical Support

Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof

of initial purchase when calling. If a product requires further inspection, the Technical Service representative will

explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the

United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service

Center Locator on the JET website.

More Information

JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor

or visit the JET website.

How State Law Applies

This warranty gives you specific legal rights, subject to applicable state law.

Limitations on This Warranty

JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT.

EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR

INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR

PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are

given as general information and are not binding. JET reserves the right to effect at any time, without prior notice,

those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason

whatsoever. JET

branded products are not sold in Canada by JPW Industries, Inc.

Product Listing with Warranty Period

90 Days – Parts; Consumable items

1 Year – Motors; Machine Accessories

2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used

for industrial or commercial purposes

5 Year – Woodworking Machinery

Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist

Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools

NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries,

Inc., or any of its successors in interest to the JET brand.

Table of Contents

Warranty and Service .................................................................................................................................... 2

Table of Contents .......................................................................................................................................... 3

IMPORTANT SAFETY INSTRUCTIONS ...................................................................................................... 4

Introduction.................................................................................................................................................... 6

Specifications ................................................................................................................................................ 6

Unpacking ..................................................................................................................................................... 7

Contents of the Shipping Container .......................................................................................................... 7

Installation and Assembly ............................................................................................................................. 8

Installing Motor .......................................................................................................................................... 8

Wheels and Leveling Stands ..................................................................................................................... 8

Stock Stop ................................................................................................................................................. 8

Shut-Off Switch .......................................................................................................................................... 9

Coolant Hose ............................................................................................................................................. 9

Grounding Instructions .............................................................................................................................. 9

Extension cords ....................................................................................................................................... 10

Adjustments ................................................................................................................................................ 11

Vise .......................................................................................................................................................... 11

Squaring Vise to Blade ............................................................................................................................ 11

Positioning the Vise ................................................................................................................................. 11

Miter Cuts ................................................................................................................................................ 12

Setting Downfeed Rate............................................................................................................................ 12

Blade Tension .......................................................................................................................................... 12

Blade Tracking ......................................................................................................................................... 12

Setting Blade Speed ................................................................................................................................ 13

Blade Guides ........................................................................................................................................... 14

Blade Replacement ................................................................................................................................. 15

Bow Stop ................................................................................................................................................. 15

Operation..................................................................................................................................................... 16

Troubleshooting HBS-814GH Band Saw .................................................................................................... 18

Replacement Parts ...................................................................................................................................... 19

Base Assembly ........................................................................................................................................ 20

Bow Assembly ......................................................................................................................................... 21

Parts List: HBS-814GH Band Saw .......................................................................................................... 22

Gear Box Assembly ................................................................................................................................. 26

Parts List: Gear Box Assembly ................................................................................................................ 27

Electrical Control Box Assembly ............................................................................................................. 28

Parts List: Electrical Control Box Assembly ............................................................................................ 29

Electrical Connections ................................................................................................................................. 30

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To reduce risk of injury:

1. Read and understand the entire owner’s manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with

all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This band saw is designed and intended for use by properly trained and experienced personnel only.

If you are not familiar with the proper and safe operation of a band saw, do not use until proper

training and knowledge have been obtained.

5. Do not use this band saw for other than its intended use. If used for other purposes, JET disclaims

any real or implied warranty and holds itself harmless from any injury that may result from that use.

6. Always wear approved safety glasses/face shields while using this band saw. Everyday eyeglasses

only have impact resistant lenses; they are not safety glasses.

7. Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past

the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips

are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

10. Make certain the switch is in the OFF position before connecting the machine to the power supply.

11. Make certain the machine is properly grounded.

12. Make all machine adjustments or maintenance with the machine unplugged from the power source.

13. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting

wrenches are removed from the machine before turning it on.

14. Keep safety guards in place at all times when the machine is in use. If removed for maintenance

purposes, use extreme caution and replace the guards immediately.

15. Check damaged parts. Before further use of the machine, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation. A guard or other part that is damaged should

be properly repaired or replaced.

16. Provide for adequate space surrounding work area and non-glare, overhead lighting.

17. Keep the floor around the machine clean and free of scrap material, oil and grease.

18. Keep visitors a safe distance from the work area. Keep children away.

19. Make your workshop child proof with padlocks, master switches or by removing starter keys.

20. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are

careless acts that can result in serious injury.

21. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other

moving parts. Do not overreach or use excessive force to perform any machine operation.

22. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for

which it was not designed. The right tool will do the job better and safer.

23. Use recommended accessories; improper accessories may be hazardous.

24. Maintain tools with care. Keep blades sharp and clean for the best and safest performance. Follow

instructions for lubricating and changing accessories.

25. Make sure the work piece is securely clamped in the vise. Never use your hand to hold the work

piece.

26. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do

not use your hands.

27. Check coolant level daily. Replace dirty or weak coolant.

28. Do not stand on the machine. Serious injury could occur if the machine tips over.

29. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

30. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

- - SAVE THESE INSTRUCTIONS - -

WARNING: Some dust, fumes and gases created by power sanding, sawing, grinding, drilling,

welding and other construction activities contain chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead based paint

• crystalline silica from bricks, cement and other masonry products

• arsenic and chromium from chemically treated lumber

Your risk of exposure varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment,

such as dust masks that are specifically designed to filter out microscopic particles. For more

information go to http://www.p65warnings.ca.gov/ and http://www.p65warnings.ca.gov/wood.

WARNING: This product can expose you to chemicals including lead which is known to the State of

California to cause cancer and birth defects or other reproductive harm, and ethylbenzene which is

known to the State of California to cause cancer. For more information go to

http://www.p65warnings.ca.gov.

Introduction

This manual is provided by JET covering the safe operation and maintenance procedures for a JET

Model HBS-814GH Horizontal Band Saw. This manual contains instructions on installation, safety

precautions, general operating procedures, maintenance instructions and parts breakdown. This machine

has been designed and constructed to provide consistent, long-term operation if used in accordance with

instructions set forth in this manual. If there are any questions or comments, please contact either your

local supplier or JET. JET can also be reached at our web site: www.jettools.com.

http://www.jettools.com/us/en/service-and-support/product-registration/

Specifications

Model Number ............................................................................................................................. HBS-814GH

Stock Number ..................................................................................................................................... 414466

Round Capacity at 90° (in.) ........................................................................................................................... 8

Round Capacity at 45° (in.) ..................................................................................................................... 6-1/2

Rectangle Capacity at 90° (W x H) (in.) .................................................................................... 14 x 8; 2 x 14

Rectangle Capacity at 45° (W x H) (in.) .................................................................................. 6-1/2 x 6; 2 x 7

Throat Depth (in.) .......................................................................................................................................... 8

Vise Swivel (deg.) ....................................................................................................................................... 45

Blade Wheel Diameter (in.) ......................................................................................................................... 12

Blade Speeds (SFPM) .............................................................................................................. 135, 197, 256

Bed Height (in.) ........................................................................................................................................... 26

Motor .................................................................................................. 1HP, 1Ph, 110/220V (pre-wired 110V)

Overall Dimensions (L x W x H)(in.) .......................................................................... 51-1/2 x 18-1/8 x 44-7/8

Net Weight (lbs.) ....................................................................................................................................... 287

Shipping Weight (lbs.) ............................................................................................................................... 342

The above specifications were current at the time this manual was published, but because of our policy of

continuous improvement, JET reserves the right to change specifications at any time and without prior

notice, without incurring obligations.

Unpacking

Open shipping container and accessory boxes,

and check for shipping damage. Report any

damage immediately to your distributor and

shipping agent. Do not discard any shipping

material until the Band Saw is assembled and

running properly.

Compare the contents of your container with the

following parts list to make sure all parts are

intact. Missing parts, if any, should be reported

to your distributor. Read the instruction manual

thoroughly for assembly, maintenance and

safety instructions.

Contents of the Shipping Container

1 Band Saw

2 Leveling Stands (with hex nuts)

2 Wheels

1 Axle

4 Flat Washers

2 Split Pins

1 Stock Stop

1 Stock Stop Rod

1 Can White Touch-Up Paint

1 Overload Fuse 10A

1 Owner's Manual

1 Warranty Card

Read and understand the entire contents of this manual before attempting set-up

or operation! Failure to comply may cause serious injury.

Installation and Assembly

Remove all crating and plastic from around the

band saw. Remove any lag screws or holding

straps which secure the band saw to the wood

pallet.

Unpainted areas of the machine have been

treated with a rust preventative. This should be

removed with a soft cloth and a mild solvent. Do

not use paint thinner, lacquer thinner, gasoline

or mineral spirits; these will damage painted and

plastic surfaces. Do not use an abrasive pad.

Installing Motor

Mount the motor to the gearbox using the four

M10 x 30 socket head cap screws and four M10

lock washers, through the holes in the motor’s

flange. See Figure 1. The key in the motor shaft

must line up with the keyway in the gearbox

opening.

Wheels and Leveling Stands

1. Slide the band saw at an angle so that the

edges hang over the sides of the pallet.

2. Insert the axle through the holes at the right

end of the band saw cabinet (opposite the

end where the lifting handle is mounted).

See Figure 2.

3. Install a wheel and two flat washers on each

end of the axle. Insert a split pin through the

hole in the axle and bend the ends of the

split pin to secure the wheel on the axle.

4. Install the two leveling stands at the left end

of the band saw (the end where the lifting

handle is mounted). See Figure 2. Screw

the leveling stand into the hole beneath the

band saw cabinet, and tighten the top hex

nut against the bottom of the cabinet.

5. The leveling stands can be later adjusted for

level by rotating the stand and re-tightening

the hex nut against the cabinet.

6. Roll the band saw off the pallet.

Stock Stop

1. Insert the stock stop rod into the hole at the

front of the base (Figure 3).

2. Secure the rod by tightening the hex cap

screw below the casting.

3. Slide the stock stop onto the rod, and

tighten the thumb screw. The stock stop can

be mounted so it faces either direction.

Figure 1

Figure 2

Figure 3

Shut-Off Switch

Remove the screw and hex nuts which held the

bow to the base during shipment. These should

be retained in case of future transportation of

the Band Saw.

The screw below the limit switch, shown in

Figure 4, has been pre-set at the factory so that

the switch will contact the screw and stop the

blade after each cutting operation.

Coolant Hose

Before operating, the coolant drain hose (Figure

5) must be connected to the coolant pan and the

other end of the hose placed into the filter cup in

the tank as shown.

The hose from the coolant pump is attached to a

valve which should be inserted into the hole on

the guide assembly (see Figure 17).

Grounding Instructions

Electrical connections must

be made by a qualified electrician in

compliance with all relevant codes. This

machine must be properly grounded to help

prevent electrical shock and possible fatal

injury.

This machine must be grounded. In the event of

a malfunction or breakdown, grounding provides

a path of least resistance for electric current to

reduce the risk of electric shock.

This band saw is pre-wired for 115 volt and is

equipped with an electric cord having an

equipment-grounding conductor and a

grounding plug similar to that shown in Figure 6.

The plug must be inserted into a matching outlet

that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit

the outlet, have the proper outlet installed by a

qualified electrician.

Improper connection of the equipment-

grounding conductor can result in a risk of

electric shock. The conductor, with insulation

having an outer surface that is green with or

without yellow stripes, is the equipment-

grounding conductor. If repair or replacement of

the electric cord or plug is necessary, do not

connect the equipment-grounding conductor to a

live terminal.

Check with a qualified electrician or service

personnel if the grounding instructions are not

completely understood, or if in doubt as to

whether the machine is properly grounded.

Figure 4

Figure 5

Figure 6

115 Volt Operation

As received from the factory, your band saw is

ready to operate at 115 volt power, using an

outlet and a plug that look similar to those

illustrated in Figure 6.

A temporary adapter, which looks like the

adapter illustrated in Figure 7, may be used to

connect this plug to a two-pole receptacle as

shown, if a properly grounded outlet is not

immediately available. The temporary adapter

should only be used until a properly

grounded outlet can be installed by a

qualified electrician.

The green colored rigid ear, lug or tab,

extending from the adapter must be connected

to a permanent ground such as a properly

grounded outlet box, as shown in Figure 7.

Make sure the voltage of your power supply

matches the specifications on the motor plate of

the Band Saw.

Conversion to 220 Volt

If 220 volt, single phase operation is desired, the

following instructions must be followed:

1. Disconnect machine from power source.

2. Open the electrical box and change the

position of the fuse from the 115V slot to the

220V slot. An electrical drawing is included

inside the electrical box, and is also shown

on page 31 of this manual.

3. The 115V attachment plug supplied with the

band saw must be replaced with a UL-listed

plug suitable for 220 volt operation. The

band saw must comply with all local and

national codes after the 220 volt plug is

installed. The band saw with a 220 volt plug

should only be connected to an outlet

having the same configuration (Figure 8).

No adapter is available or should be used

with the 220 volt plug.

Extension cords

If an extension cord is necessary, make sure the

cord rating is suitable for the amperage listed on

the machine’s motor plate. An undersized cord

will cause a drop in line voltage resulting in loss

of power and overheating. Use only three wire

extension cords that have three-prong

grounding plugs and three-pole receptacles that

accept the machine’s plug.

Use the chart in Figure 9 as a general guide in

choosing the correct size cord. If in doubt, use

the next heavier gauge. The smaller the gauge

number, the heavier the cord.

Figure 7

Figure 8

Recommended Gauges (AWG) of Extension Cords

Amps

Extension Cord Length *

feet

100

feet

150

feet

200

feet

< 5 16 16 16 14 12 12

5 to 8 16 16 14 12 10 NR

8 to 12 14 14 12 10 NR NR

12 to 15 12 12 10 10 NR NR

15 to 20 10 10 10 NR NR NR

21 to 30 10 NR NR NR NR NR

*based on limiting the line voltage drop to 5V at 150% of the

rated amperes.

NR: Not Recommended.

Figure 9

Adjustments

Vise

There are two sets of holes in the bed to mount

the right jaw. The inner hole and slot (A, Figure

10) are used for miter cuts. The outer hole and

slot (B, Figure 10) are used for square, or 90°

cuts. Figure 10 shows the vise located in the “A”

position for miter cuts.

Use only position “A” for miter cuts. If the “A”

position is used for square cuts, it leaves more

blade exposed to the right of the jaw.

Squaring Vise to Blade

1. To set up for square cutting, move the right

jaw to “B” position (Figure 10). Place a

machinist’s square on the bed against the

blade and the right vise jaw. The square

should lie along the entire length of the jaw

and blade without a gap.

2. If adjustment is necessary, slightly loosen

the front screw on the right jaw. Loosen the

hex nut at the center of the right jaw and

adjust jaw so the square lines up properly.

3. Re-tighten the hex nut and the front screw.

4. Loosen the handle (C, Figure 10) on the left

jaw. Move the left jaw until it contacts flush

with the right jaw.

5. Tighten the handle (C, Figure 10). The vise

is now set for square cuts.

Positioning the Vise

Keep hands away from blade

while adjusting the vise.

1. The workpiece is placed against the fixed

jaw, which has already been squared (see

“Squaring Vise to Blade”), or has been

locked at the appropriate angle (see “Miter

Cuts”).

2. The vise has a quick-release feature which

allows fast positioning of the movable jaw

against the workpiece and then a final

tightening with the handle. Lift up on the

quick release lever (D, Figure 11), then

push the movable jaw by hand until it

contacts the workpiece.

3. Push down the quick release lever (D,

Figure 11).

4. Turn the lead screw handle (E, Figure 11)

clockwise to continue the tightening process

of the movable jaw until the workpiece is

securely clamped.

Figure 10

(fixed jaw shown in “A” position for mitering)

Figure 11

5. The quick release function can also be used

to back off the movable jaw when the cut is

finished.

Miter Cuts

1. For miter cuts, move the fixed jaw to the

inner holes, or “A” position, as shown in

Figure 10.

2. Rotate the fixed jaw to the desired angle,

and tighten the center hex nut.

NOTE: There is an angle scale on the back

side of the bed. This is for reference only.

Check angles with a protractor if greater

precision is needed.

3. Adjust the movable jaw in the manner

described above, and tighten the handle (C,

Figure 10).

Setting Downfeed Rate

The downfeed rate of the blade is important to

band saw performance. Excessive pressure of

blade against the workpiece may break the

blade or stall the saw. In contrast, insufficient

pressure rapidly dulls the blade.

Turn the valve lever (Figure 12)

counterclockwise to lower the bow. The rate of

downfeed is controlled by the dial setting (Figure

12).

Blade Tension

Blade tension has been set at the factory. When

installing a new blade, use the tension handle

(Figure 13) to adjust blade tension (clockwise to

tighten). Tension is set properly when the

indicator moves into the “green” area on the

scale.

Blade Tracking

Tracking the blade requires

that the band saw be operating while the

back cover is removed. Use extreme caution.

Blade tracking has been tested at the factory.

Adjustment is rarely required when the blade is

used properly and if the blade is correctly

welded. If a tracking problem should occur,

adjust the machine as follows:

1. Raise the bow to its highest position. Make

sure the hydraulic cylinder valve is closed

so the bow remains in place.

2. The blade should be properly tensioned.

NOTE: Keep proper tension on the blade at

all times using the blade tension adjustment.

3. Open the back wheel cover.

Figure 12

Figure 13

While performing the

following steps, keep the blade from rubbing

excessively on the shoulder of the wheel.

Excessive rubbing will damage the wheel

and/or the blade.

4. Start the saw. Turn the set screw (Figure

14) to tilt the idler wheel until the blade is

touching the shoulder of the idler wheel.

5. Turn the set screw (Figure 14) so the blade

starts to move away from the shoulder of

the wheel; then immediately turn the set

screw in the other direction so the blade

stops; then moves slowly towards the

shoulder. NOTE: This adjustment is

sensitive; do it gradually and in small

increments allowing the wheel to respond to

the changes.

Keep your fingers clear of

the blade and wheel to avoid injury.

6. Turn the set screw to stop the shifting of the

blade on the wheel as it gets closer to the

wheel shoulder. Put a six-inch length of

paper between the blade and the wheel.

See Figure 15. The paper should not be cut

as it passes between the wheel shoulder

and the blade.

7. Turn the set screw a small amount. Repeat

the insertion of the paper between the wheel

shoulder and the blade until the paper is cut

into two pieces.

NOTE: You may have to repeat the check

with the paper several times before the

blade and the shoulder cut the paper into

two pieces. Do not hurry the adjustment.

Patience and accuracy here will pay off with

better, more accurate, quieter cutting and

longer machine and blade life.

8. When the paper is cut, back off the set

screw slightly. This assures that the blade is

not touching the shoulder of the wheel.

IMPORTANT: If the blade is allowed to run

against the shoulder of the wheel, it will

wear off the shoulder.

Setting Blade Speed

Rotate the dial (see Figure 16) to the desired

setting – 135, 197 or 256 feet per minute.

Do not change blade speed

during a cutting operation.

Figure 14

Figure 15

Figure 16

Material chips or shavings are the best indicator

of proper blade speed and downfeed rate. The

ideal chip is thin, tightly curled and warm to the

touch. Chips that range from golden brown to

black indicate excessive force. Blue chips

indicate extreme heat from too high a blade

speed, which will shorten blade life. Thin or

powdered chips indicate insufficient downfeed

rate.

Blade Guides

Loosen the handle (Figure 17) and slide the

guide assembly as close to the workpiece as

possible. This will prevent excessive exposure

of the blade during operation.

[NOTE: The handle (Figure 17) can be adjusted

out of the way. Lift up on the handle and rotate it

on the pin. Release the handle, making sure it

seats itself properly on the pin.]

The guide bearings and carbide guide blocks

come pre-adjusted from the factory, but should

be inspected frequently and adjustments made

as needed. For most efficient operation and

maximum accuracy, provide 0.001” clearance

between the blade and the guide bearings. The

bearings will still turn freely with this clearance.

If the clearance is incorrect, the blade may track

off the drive wheel.

1. Disconnect machine from power source.

2. Loosen the two socket head cap screws (A,

Figure 18) and move the guide seat (B,

Figure 18) up or down until the guide blocks

(D, Figure 18) are positioned adequately

across the width of the blade.

3. Loosen the socket head cap screws (C,

Figure 18) on the carbide guide blocks (D,

Figure 18) and shift both guide blocks until

they place a light pressure on the blade. Re-

tighten the socket head cap screws (C,

Figure 18).

4. The outer guide bearing (E, Figure 18) is

mounted to an eccentric bushing and is

adjustable. Loosen the hex nut (F, Figure

18) and rotate the bearing shaft (G, Figure

18) with a wrench until the bearing (E,

Figure 18) clears the blade by

approximately .001”. Do not pinch the blade.

5. Re-tighten hex nut (F, Figure 18).

6. Repeat these steps for the other blade

guide assembly.

Figure 17

Figure 18

Blade Replacement

A general-use variable-tooth blade is provided

with this metal cutting band saw. Additional

blades can be used and are available from your

JET distributor.

The choice of blade pitch is governed by the

thickness of the work to be cut: the thinner the

workpiece, the more teeth advised. A minimum

of 3 teeth should engage the workpiece at all

times. If the teeth of the blade are so far apart

that they straddle the work, severe damage to

the workpiece and to the blade can result.

1. Disconnect machine from power source.

2. Loosen the handle (Figure 17) and move

the blade guides away from the wheel, as

shown in Figure 19.

3. Raise the bow, making sure the hydraulic

cylinder is closed so the bow will remain

stationary.

4. Open the back cover, by loosening the two

knobs and the four screws on the brackets.

5. Loosen tension on the blade.

6. Remove the blade from between the guides

and from around the wheels. (Use gloves

when handling sharp blades!).

7. Install new blade on wheels, making sure

the teeth point downward in the proper

cutting direction. See Figure 20; also notice

the blade direction arrow on the front of the

bow.

8. Increase blade tension just enough to hold

the blade on the wheels. Make sure back of

blade rests lightly against the shoulder of

both wheels.

9. Twist blade slightly to allow it to slip into the

guides.

10. The blade should be tensioned and tracked

properly before use. See “Blade Tension”

and “Blade Tracking” above.

Bow Stop

The stop screw (Figure 21) controls the depth of

fall of the bow to prevent the blade from hitting

the bed casting. The stop screw has been set at

the factory. If future adjustment is needed,

loosen the hex nut and rotate the screw, then re-

tighten the hex nut.

Figure 19

Figure 20

Figure 21

Operation

Figure 22 shows the control panel functions.

The Emergency Stop shuts down all functions

on the band saw. The machine will not start if

the emergency stop is still engaged. To start the

machine, twist the emergency stop button until it

pops back out.

IMPORTANT: When cutting magnesium, never

use soluble oils or emulsions (oil-water mix) as

water will greatly intensify any accidental

magnesium chip fire. See your industrial coolant

supplier for specific coolant recommendations

when cutting magnesium.

General Operating Procedure:

1. Give machine an overall inspection. Verify

that all guards, covers, etc. are in place and

in working order, the blade is tensioned

properly and the tooth direction matches the

arrow on the bow. Check that the blade

guides are set correctly, and also the wire

brush.

2. Place workpiece in vise and tighten vise.

The workpiece should be fitted directly

between the jaws without adding other

objects.

When the workpiece to be cut is a profiled

section, flat piece or special shape, refer to

the examples shown in Figure 23 for proper

clamping positions. The top row shows

acceptable clamping positions, the bottom

row shows unacceptable positions.

If the thickness of the profiled section is very

thin, a piece which duplicates the profile

should be fitted inside the workpiece itself,

to prevent the workpiece being crushed

between the jaws.

Never hold a workpiece by

hand when cutting it – the workpiece should

be firmly secured in the vise. Do not reach

into the cutting area during cutting

operations.

3. Rotate the speed dial to the desired setting.

Do not rotate the speed dial during a

cutting operation.

4. Set a suitable downfeed rate for that

operation on the cylinder dial.

5. Push the start button to start the blade

circulating.

6. Turn on the coolant flow.

Figure 22

Figure 23

7. Open the valve on the hydraulic cylinder to

allow the bow to descend in a gradual and

controlled manner.

8. The machine will shut off at the completion

of the cut. Turn off the coolant flow, and

remove the workpiece.

9. Return the bow to vertical position for the

next cut.

User-Maintenance

Before doing maintenance

on the machine, disconnect it from the

electrical supply by pulling out the plug or

switching off the main switch. Failure to

comply may cause serious injury.

Clean the band saw regularly after each day’s

work. Clear metal shavings with the provided

brush, do not use your hands. Do not use

compressed air.

To prevent corrosion of machined surfaces

when a soluble oil is used as coolant, pay

particular attention to wiping dry the surfaces

where fluid accumulates and does not evaporate

quickly, such as between the machine bed and

vise.

If the power cord is worn, cut, or damaged in

any way, have it replaced immediately.

All ball bearings are permanently lubricated and

sealed. They require no further lubrication.

Grease the vise lead screw as needed.

Place a thin coat of oil on the bed surface on

which the vise jaw slides.

Maintain coolant level. Low coolant level can

cause foaming and high blade temperatures.

Replace dirty coolant; dirty or weak coolant can

clog the pump, cause crooked cuts, a low

cutting rate and/or permanent blade damage. To

fill the tank, remove the filter cup and pour

coolant into the hole. A “Hi/Lo” mark on the tank

indicates proper level (see Figure 5).

Maintain oil level in the gear box, using SAE No.

10. To check level of the gear box oil, place bow

in down position so that oil drains down. Check

level in sight glass on side of gear casing.

Correct level is the dot in the middle of the sight

glass. Figure 24 shows the locations of the fill

hole, sight glass and drain plug for the gear box.

Completely drain and refill the gear box oil once

a year.

Figure 24

Troubleshooting HBS-814GH Band Saw

Trouble Probable Cause Remedy

Motor will not start. No incoming power. Check plug connection.

Blown electrical panel fuses. Replace fuses.

Thermal overload has tripped.

Wait several minutes for overload to

reset itself.

Defective motor, switch, power cable,

or plug.

Qualified electrician/service personnel

should inspect these items.

Overload trips

frequently.

Motor is overheating. Check that motor air intakes are clear.

Downfeed rate too fast. Reduce downfeed rate.

Motor is faulty.

Motor should be inspected by

qualified electrician/service personnel.

Band Saw vibrates

excessively.

Base on uneven surface. Adjust base for even support.

Saw blade has cracks. Replace blade immediately.

Too heavy a cut.

Reduce downfeed rate and blade

speed.

Miter cuts not

accurate. Setting of the miter stops is not

correct.

Loosen the screws and adjust the

stops to correct positions. Use an

adjustable square or protractor to

check angle settings.

Blade is worn, cutting crooked. Replace blade.

Cuts not square. Feed pressure too great. Decrease feed pressure.

90° angle stop is not set correctly.

Adjust stop until blade is square with

vise.

Incorrect blade toothing in relation to

workpiece.

Check Machinist’s Handbook for

recommended blade type.

Blade is worn, cutting crooked. Replace blade.

Incorrect adjustment of bearing

guides and guide assembly.

Re-adjust these. See page 14.

Workpiece incorrectly positioned in

vise.

Check positioning and clamping in the

vise.

Poor blade tension. Check and correct if needed.

Finished surface of

workpiece is rough,

unsatisfactory.

Blade is dull. Replace blade.

Improper blade for cutting operation.

Check Machinist’s Handbook for

blade recommendations.

Downfeed rate too fast. Reduce downfeed rate.

Blade tension too low. Increase blade tension.

Trouble Probable Cause Remedy

Excessive blade

breakage.

Incorrect blade tension. Adjust accordingly (see page 12).

Incorrect blade speed or downfeed

rate.

Adjust acccordingly.

Workpiece loose in vise. Clamp workpiece securely.

Blade rubs on wheel shoulder. Adjust blade tracking.

Teeth too coarse for material.

Use appropriate blade for material

being cut.

Teeth in contact with workpiece

before saw is started.

Start motor before blade contacts

workpiece.

Blade guides are misaligned. Adjust as needed. See page 14.

Blade too thick for wheel diameter. Use thinner blade.

Cracking at weld; poor annealing of

blade.

Replace blade.

Premature Blade

Dulling.

Teeth too coarse. Use finer tooth blade.

Blade speed too fast. Reduce speed.

Inadequate downfeed rate. Adjust cylinder dial setting as needed.

Hard spots or scale on material.

Scale: Reduce speed and increase

downfeed rate. Hard Spots: Increase

downfeed rate.

Work hardening of material

(especially stainless steel)

Increase downfeed rate.

Blade installed backwards.

Remove blade, twist inside-out and

re-install.

Insufficient blade tension. Adjust as needed.

Replacement Parts

Replacement parts are listed on the following pages. To order parts or reach our service department, call

1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and

Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from

JET. Some parts are shown for reference only, and may not be available individually.

Base Assembly

Page is loading ...

JET HBS-814GH Owner's manual

JET HBS-814GH Owner's manual

JET HBS-814GH Owner's manual

Related papers

Other documents