ENGLISH
2
3
ENGLISH
Precauons
Always exercise care when operang and handling the DT592IC/ DT592IB.•
Never disassemble any poron of the enclosure, as this will void any product warranty on the •
DT592IC/ DT592IB.
Do not use any AC/DC adapter other than the one provided with the device or a replacement •
acquired from the manufacturer.
In the unlikely event that smoke, abnormal noise or strange odor is present, immediately power •
down the DT592IC/ DT592IB and disconnect all power sources. Please report the problem to
your device provider immediately.
Basic Features
The DT592IC/ DT592IB integrates a bright 21.5
”
display with capacive touch, USB ports, and
is complemented by a suite of opons including a front camera and a smart card reader for
comprehensive point-of-care applicaons.
Powering ON and OFF
If your DT592IC/ DT592IB comes with the baery packs, please open the baery slot caps and
then put in the baery packs one by one. If not, please use the AC-DC adapter with the DT592IC/
DT592IB for the power supply. To acvate the DT592IC/ DT592IB, push and quickly release the
Power Buon and the display will come on in a few seconds. To put in Standby mode, push and
quickly release the Power Buon. To turn off for extended storage, power off the device safely using
any soware funcon that
“
shuts down computer
”
provided in the soware operang system.
NOTE: The baery packs shipped with your device may be low in power
—
please use the AC-DC
adapter with the DT592IC/ DT592IB when seng up the device for the first me to fully charge
the internal baery packs. You may charge the external baery pac
ks with them aached to the
DT592IC/ DT592IB, or with the oponal baery charger kit.
NOTE: When the baery pack(s) is (are) charging, the blue-colored Baery LED should blink slowly.
If plugging in the AC-DC adapter does not trigger this blinking acvity and the LED stays dark, the
baery pack(s) may have been drained substanally. Try unplugging/ replugging the AC-DC adapter
to the DT592IC/ DT592
IB a few mes to acvate the charging process.
NOTE: To conserve power, use (push and quick release) the Power Buon to put the device in
“
Standby
”
mode while not in use. Pushing briefly on the same buon will wake up the system
within seconds.
NOTE: Avoid using the Power Buon (
“
hold 4+ seconds
”
feature) to turn off the device
—
this form
of hardware shutdown is intended to be a means of recovery from
device lockups, and not as
normal operaon.
Power/Baery LED Status
Blue indicates the baery is 25% to 100% charged•
Blinking blue indicates the baery is charging•
Orange indicates that the baery is between 11% to 25%•
Blinking Orange indicates that the baery is below 10%•
Wireless Networking
Wireless LAN
The DT592IC/ DT592IB is oen delivered with an embedded (user-inaccessible) 802.11a/b/g/n
WLAN adapter equipped with a hidden custom antenna.
Through the support of typical WLAN adapters, the The DT592IC/ DT592IB should be able to •
detect all 802.11 access points in the vicinity for you to select the access point of your choice for
connecon.
The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT592IC/ DT592IB and the access •
points have to match. The SSID is case-sensive and it is recommended that you enable WEP/
WPA/WPA2 encrypon (or advanced alternaves) for secure access.
When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your •
networking equipment literature to properly configure associated sengs such as Authencaon
mode, etc.
Refer to the access point operang manuals for seng up the 802.11 access points.•
Bluetooth
The DT592IC/ DT592IB features a built-in Bluetooth adapter that operates on the Microso
Windows Bluetooth protocol. The Bluetooth configuraon applicaon is invoked from the System
Tray or from the Control Panel. Follow the instrucons and opons provided within the applicaon
to configure and invoke Bluetooth connecvity with the corresponding peripherals.
NOTE: Bluetooth devices or accessories that are not compable with the Microso Windows
Bluetooth protocol may not work with the DT592IC/ DT592IB.
Baery Indicator