Fender ST-75 Tripod Speaker Stand Owner's manual

Type
Owner's manual

Fender ST-75 Tripod Speaker Stand

The Fender ST-75 Tripod Speaker Stand is a heavy-duty stand designed to support up to 75 lbs. (34 kg) of properly installed equipment. It is constructed from rugged anodized aluminum alloy tubing and features a dual diameter mounting pole with both 1 3/8” and 1.5” (35 mm & 38 mm) diameters, making it compatible with a wide range of speaker enclosures.

The ST-75 is easy to set up and adjust. Simply loosen the leg fitting handknob, pivot the legs out, and turn the tripod upright.

Fender ST-75 Tripod Speaker Stand

The Fender ST-75 Tripod Speaker Stand is a heavy-duty stand designed to support up to 75 lbs. (34 kg) of properly installed equipment. It is constructed from rugged anodized aluminum alloy tubing and features a dual diameter mounting pole with both 1 3/8” and 1.5” (35 mm & 38 mm) diameters, making it compatible with a wide range of speaker enclosures.

The ST-75 is easy to set up and adjust. Simply loosen the leg fitting handknob, pivot the legs out, and turn the tripod upright.

The ST-75 heavy duty tripod speaker stand is constructed from rugged
anodized aluminum alloy tubing and is capable of supporting up to 75 lbs.
(34 kg) of properly installed equipment. The ST-75’s dual diameter mounting
pole features both 1 3/8” and 1.5” (35 mm & 38 mm) diameters and makes
a great accessory for the Fender Artist Series or SPL Series 1211 Mk-II and
1225 Mk-II loudspeaker systems. Because loudspeaker enclosures placed
on the ST-75 could be damaged or cause bodily harm if they fall, please read
through these instructions and heed all caution and safety warnings.
IMPORTANT
When setting up your ST-75 tripod speaker stand, make sure it is placed on
a dry, flat and secure surface. Also, when placing, raising or lowering gear
on the ST-75, it is recommended that at least two people undertake these
procedures. All telescoping tubes have gray-colored warning stripes to
indicate the maximum extension of the tube. DO NOT EXCEED THESE
WARNING INDICATORS.
YOUR FENDER
®
ST-75 TRIPOD SPEAKER STAND
P/N 051716
Tighten collar handknob
1
Loosen leg fitting
handknob
2
Turn tripod upside
down and pivot legs
out.
3
Turn tripod upright and slide leg
fitting to adjust the width of the leg
spread until the cross bars are
parallel to the floor. This will ensure
the ST-75 is at its maximum
footprint (Using a smaller footprint
will adversely affect the stability of
the unit). Tighten the handknob.
4
Place your speaker on the stand.
Remember to secure all wires
coming from the ST-75 for reasons
of both safety and good
presentation (loose wires can be
tripped on and give a cluttered,
unprofessional appearance).
5
Loosen collar handknob and raise
equipment to the desired height.
Re-tighten handknob and check the
stability of the unit at the desired
height setting.
6
REMEMBER ...
Check to ensure that all handknobs are
secure when supporting equipment.
Always loosen handknobs with caution.
Clean your ST-75 Tripod using a damp
cloth or any non-abrasive cleaner.
Make sure that speakers are securely
mounted on the stand. Do not exceed
published weight limitations for the ST-75.
  • Page 1 1

Fender ST-75 Tripod Speaker Stand Owner's manual

Type
Owner's manual

Fender ST-75 Tripod Speaker Stand

The Fender ST-75 Tripod Speaker Stand is a heavy-duty stand designed to support up to 75 lbs. (34 kg) of properly installed equipment. It is constructed from rugged anodized aluminum alloy tubing and features a dual diameter mounting pole with both 1 3/8” and 1.5” (35 mm & 38 mm) diameters, making it compatible with a wide range of speaker enclosures.

The ST-75 is easy to set up and adjust. Simply loosen the leg fitting handknob, pivot the legs out, and turn the tripod upright.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI