LG ARNU15GSBL4 User manual

Brand: LG

Model: ARNU15GSBL4

Category: Split-system air conditioners

Type: User manual

INSTALLATION MANUAL

AIR

CONDITIONER

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring standards by authorized

personnel only. Please retain this installation manual for future reference after reading it thoroughly.

WALL MOUNTED

Original instruction

[Representative] LG Electronics Inc. EU Representative :

LG Electronics European Shared Service Center B.V.

Krijgsman 1, 1186 DM Amstelveen, The Netherlands

[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro,

Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA

www.lg.com

MFL68800316

Rev.00_040419

ENGLISH

ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

ΕΛΛΗΝΙΚΆ

ČEŠTINA

NEDERLANDS

POLSKI

LIMBA ROMÂNĂ

РУССКИЙ ЯЗЫК

УКРАÏНСЬКА

ҚАЗАҚ ТІЛІ

БЕЛАРУСКАЯ МОВА

O‘ZBEK TILI

TIPS FOR SAVING ENERGY

ENGLISH

• Do not cool excessively indoors. This may be harmful for your health and may consume more

electricity.

• Block sunlight with blinds or curtains while you are operating the air conditioner.

• Keep doors or windows closed tightly while you are operating the air conditioner.

• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.

• Speed up the fan to cool or warm indoor air quickly, in a short period of time.

• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air

conditioner is used for many hours.

• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the

air flow or weaken the cooling / dehumidifying functions.

For your records

Staple your receipt to this page in case you need it to prove the date of purchase or for warranty

purposes. Write the model number and the serial number here:

Model number :

Serial number :

You can find them on a label on the side of each unit.

Dealer’s name :

Date of purchase :

Here are some tips that will help you minimize the power consumption when you use the air

conditioner. You can use your air conditioner more efficiently by referring to the instructions

below:

TIPS FOR SAVING ENERGY

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE

APPLIANCE.

Always comply with the following precautions to avoid dangerous

situations and ensure peak performance of your product

WARNING

It can result in serious injury or death when the directions are

ignored

CAUTION

It can result in minor injury or product damage when the

directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result

in hazards to you and others.

• Installation must conform with local building codes.

• The information contained in the manual is intended for use

by a qualified service technician familiar with safety

procedures and equipped with the proper tools and test

instruments.

• Failure to carefully read and follow all instructions in this

manual can result in equipment malfunction, property

damage, personal injury and/or death.

Installation

• Don’t use a power cord, a plug or a loose socket which is

damaged.

- Otherwise, it may cause a fire or electrical shock.

• For electrical work, contact the dealer, seller, a qualified

electrician, or an Authorized Service Center.

- Do not disassemble or repair the product. There is risk of fire

or electric shock.

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

• Always ground the product.

- There is risk of fire or electric shock.

• Install the panel and the cover of control box securely.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric

shock.

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

• Do not modify or extend the power cable.

- There is risk of fire or electric shock.

• Do not let the air conditioner run for a long time when the

humidity is very high and a door or a window is left open.

- Moisture may condense and wet or damage furniture.

• Be cautious when unpacking and installing the product.

- Sharp edges could cause injury. Be especially careful of the

case edges and the fins on the condenser and evaporator.

• For installation, always contact the dealer or an Authorized

Service Center.

- There is risk of fire, electric shock, explosion, or injury.

• Do not install the product on a defective installation stand.

- It may cause injury, accident, or damage to the product.

• Be sure the installation area does not deteriorate with age.

- If the base collapses, the air conditioner could fall with it,

causing property damage, product failure, and personal

injury.

• There is a risk of fire and explosion.

- Inert gas (nitrogen) should be used when you check

plumbing leaks, cleaning or repairs of pipes etc.

If you are using combustible gases including oxygen,

product may have the risk of fires and explosions.

• Use a vacuum pump or Inert (nitrogen) gas when doing

leakage test or air purge. Do not compress air or Oxygen and

do not use Flammable gases. Otherwise, it may cause fire or

explosion.

- There is the risk of death, injury, fire or explosion.

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

• Do not turn on the breaker or power under condition that front

panel, cabinet, top cover, control box cover are removed or

opened.

- Otherwise, it may cause fire, electric shock, explosion or

death.

Operation

• Do not store or use flammable gas or combustibles near the

product.

- There is risk of fire or failure of product.

CAUTION

Installation

• Always check for gas (refrigerant) leakage after installation or

repair of product.

- Low refrigerant levels may cause failure of product.

• Install the drain hose to ensure that water is drained away

properly.

- A bad connection may cause water leakage.

• Keep level even when installing the product.

- To avoid vibration or water leakage.

• Use two or more people to lift and transport the product.

- Avoid personal injury.

• Means for disconnection must be incorporated in the fixed

wiring in accordance with the wiring rules.

TABLE OF CONTENTS

ENGLISH

2 TIPS FOR SAVING ENERGY

3 IMPORTANT SAFETY INSTRUCTIONS

7 INSTALLATION PARTS

7 INSTALLATION TOOLS

8 INSTALLATION MAP

9 INSTALLATION

9 Select the best Location

9 Fixing Installation Plate

10 Drill a Hole in the Wall

10 Flaring Work

11 Connecting the Piping

15 Checking the Drainage

16 Installation of ﬁlters

17 Wiring Connection

18 DIP Switch Setting

19 Group control setting

24 Model Designation

24 Airborne Noise Emission

24 Limiting concentration

TABLE OF CONTENTS

INSTALLATION PARTS

ENGLISH

INSTALLATION TOOLS

INSTALLATION PARTS

Name Quantity Shape

Installation plate 1 EA

Type "A" screw

5 EA

Type "C" screw

2 EA

The feature can be changed according to type of model.

Screws for fixing panels are attached to decoration panel.

Figure FigureName

Screw driver

Electric drill

Measuring tape, Knife

Hole core drill

Spanner

Torque wrench

Multi-meter

Hexagonal wrench

Ammeter

Gas-leak detector

Thermometer,

Level

Flaring tool set

Name

INSTALLATION MAP

ENGLISH

INSTALLATION MAP

Vinyl tape (Wide)

• Apply after carrying out a

drainage test.

• To carry out the drainage

test, remove the air ﬁlters

and pour water into the heat

exchanger.

Saddle

Installation plate

Sleeve

Bushing-Sleeve

Putty(Gum Type Sealant)

Bend the pipe as closely

on the wall as possible,

but be careful that it

doesn't break.

NOTE

• You should purchase the installation parts.

* The feature can be changed according to type of model.

INSTALLATION

ENGLISH

Select the best Location

- There should not be any heat or steam near

the unit.

- Select a place where there are no obstacles

around of the unit.

- Make sure that condensation drainage can

be conveniently routed away.

- Do not install near a doorway.

- Ensure that the interval between a wall and

the left (or right) of the unit is more than 100

mm. The unit should be installed as high as

possible on the wall, allowing a minimum of

200 mm from ceiling.

- Use a metal detector to locate studs to

prevent unnecessary damage to the wall.

* The feature can be changed according to

type of model.

Fixing Installation Plate

The wall you select should be strong and solid

enough to prevent vibration

1 Mount the installation plate on the wall

with type "A" screws. If mounting the unit

on a concrete wall, use anchor bolts.

- Mount the installation plate horizontally

by aligning the centerline using Horizontal

meter.

2 Measure the wall and mark the centerline.

It is also important to use caution

concerning the location of the installation

plate. Routing of the wiring to power

outlets is through the walls typically.

Drilling the hole through the wall for piping

connections must be done safely.

More than 200

More than

100

More than 2 300

More than

100

(Unit : mm)

CAUTION

Install the indoor unit on the wall where

the height from the floor is more than

2 300 mm.

Ø 65

133

Right rear piping

Left rear piping

Installation Plate

Place a level on raised tab

Unit Outline

217

175

(Unit : mm)

442 442

Ø65

Ø 65

SB chassis

SC chassis

Ø 65

Ø65

Ø 65

Right rear piping

Left rear piping

Installation Plate

Measuring Tape

Hanger

Place a level on raised tab

Unit Outline

207

105

460 570

INSTALLATION

ENGLISH

Drill a Hole in the Wall

- Drill the piping hole with a Ø 65 mm hole

core drill. Drill the piping hole at either the

right or the left with the hole slightly slanted

to the outdoor side.

Flaring Work

Main cause for gas leakage is due to defect of

flaring work. Carry out correct flaring work in

the following procedure.

Cut the pipes and the cable

1 Use the piping kit accessory or the pipes

purchased locally.

2 Measure the distance between the indoor

and the outdoor unit.

3 Cut the pipes a little longer than measured

distance.

4 Cut the cable 1.5 m longer than the pipe

length.

Burrs removal

1. Completely remove all burrs from the cut

cross section of pipe/tube.

2. While removing burrs put the end of the

copper tube/pipe in a downward direction

while removing burrs location is also

changed in order to avoid dropping burrs

into the tubing.

Putting nut on

- Remove flare nuts attached to indoor and

outdoor unit, then put them on pipe/tube

having completed burr removal.

(not possible to put them on after finishing

flare work)

Flaring work

1 Firmly hold copper pipe in a bar with the

dimension shown in below table table

below.

2 Carry out flaring work with the flaring tool.

5-7 mm

(3/16"~5/16")

Indoor

WALL

Outdoor

Copper

pipe

90°

Slanted Uneven Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

Pipe diameter

Inch (mm)

A inch (mm)

Wing nut type Clutch type

Ø 1/4 (Ø 6.35) 0.04~0.05(1.1~1.3)

0~0.02

(0~0.5)

Ø 3/8 (Ø 9.52) 0.06~0.07(1.5~1.7)

Ø 1/2 (Ø 12.7) 0.06~0.07(1.6~1.8)

Ø 5/8 (Ø 15.88) 0.06~0.07(1.6~1.8)

Ø 3/4 (Ø 19.05) 0.07~0.08(1.9~2.1)

Check

1 Compare the flared work with the figure

by.

2 If a flared section is defective, cut it off

and do flaring work again.

Connecting the Piping

1 Pull the screw cap at the bottom of the

indoor unit

2 Remove the chassis cover from the unit by

loosing 2 screws

3 Pull back the tubing holder.

4 Remove pipe port cover and positioning

the tubing

* The feature can be changed according to

type of model.

Good case

- Press on the tubing cover and unfold the

tubing to downward slowly. And then bend

to the left side slowly.

INSTALLATION

ENGLISH

Inclined

Inside is shiny without scratches

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper ﬂaring =

Right

Indoor unit back side view

Tubing holder

Downwards

Left

Backwards

Chassis cover

Bar

Copper pipe

"A"

INSTALLATION

ENGLISH

Installation Information. For right piping.

Follow the instruction above.

Bad case

- Following bending case from right to left

directly may cause damage to the tubing.

* The feature can be changed according to

type of model.

Installation of Indoor Unit

1 Hook the indoor unit onto the upper

portion of the installation plate.( engage

the three hooks at the top of the indoor

unit with the upper edge of the installation

plate) Ensure that the hooks are properly

seated on the installation plate by moving

it left and right

2 Unlock the tubing holder from the chassis

and mount between the chassis and

installation plate in order to separate the

bottom side of the indoor unit from the

wall.

* The feature can be changed according to

type of model.

Piping

1 Insert the connecting cable through the

bottom side of indoor unit and connect the

cable (You can see detail contents in

'Connecting the cables' section)

View

Terminal block of indoor unit

1(L) 2(N) 3(A) 4(B)

Indoor power input

Outdoor unit

Installation plate

Tubing Holder

CAUTION

INSTALLATION

ENGLISH

2 Secure the cable onto the control board

with the cable retainer.

3 Tape the tubing pipe, drain hose and the

connection cable. Be sure that the drain

hose is located at the lowest side of the

bundle. Locating at the upper side can

cause overflow from the drain pan through

the inside of the unit.

* The feature can be changed according to

type of model.

1 Align the center of the pipes and

sufficiently tighten the flare nut by hand

2 Tighten the flare nut with a wrench

3 When needed to extend the drain hose of

indoor unit, assembly the drain pipe as

shown on the drawing

View

Terminal block of indoor unit

1(L) 2(N) 3(A) 4(B)

Indoor power input

Outdoor unit

Drain hose

Connecting pipe

Connecting

cable

Tape

Drain hose

Connecting pipe

Connecting

cable

Tape

Drain hose

If the drain hose is routed inside the room

insulate the hose with an insulation

material* so that dripping from sweating

condensation) will not damage furniture or

floors.

* Foamed polyethylene or equivalent is

recommended.

Outside diameter

Torque

Connecting the installation pipe

and drain hose to the indoor unit.

Indoor unit tubing Flare nut Pipes

mm inch kgf.m

Ø 6.35 1/4 1.8~2.5

Ø 9.52 3/8 3.4~4.2

Ø 12.7 1/2 5.5~6.5

Ø 15.88 5/8 6.3~8.2

Ø 19.05 3/4 9.9~12.1

Wrench

Indoor unit tubing

Open-end wrench

(ﬁxed)

Connection

pipe

Flare nut

Vinyl tape(narrow)

Adhesive

Drain pipe

Indoor unit drain hose

CAUTION

INSTALLATION

ENGLISH

Wrap the insulation material

around the connecting portion.

1 Overlap the connection pipe insulation

material and the indoor unit pipe insulation

material. Bind them together with vinyl

tape so that there may be no gap.

2 Set the tubing cutting line upward.

Wrap the area which accommodates the

rear piping housing section with vinyl tape.

3 Bundle the piping and drain hose together

by wrapping them with vinyl tape sufficient

enough to cover where they fit into the

rear piping housing section.

Finishing the indoor unit

installation

1 Mount the tubing holder in the original

positon.

2 Ensure that the hooks are properly seated

on the installation plate by moving it left

and right.

3 Press the lower left and right sides of the

unit against the installation plate until the

hooks engage into their slots (clicking

sound).

4 Finish the assembly by screwing the unit

to the installation plate by using two

pieces of type "C" screws. And assemble a

chassis cover.

Insulation material

Gas Pipe

Liquid Pipe

Cutting Line

Good Case Bad Case

* Tubing cutting line have to be upward.

Vinyl tape(narrow)

Connection pipe

Connecting cable

Vinyl tape (wide)

Wrap with vinyl tape

Indoor unit pipe

Pipe

Type 'C' screw

Wrap with vinyl tape

Drain hose

Pipe

Vinyl tape(wide)

INSTALLATION

ENGLISH

Checking the Drainage

To check the drainage.

1 Pour a glass of water on the evaporator.

2 Ensure the water flows through the drain

hose of the indoor unit without any

leakage and goes out the drain exit.

Drain piping

1 The drain hose should point downward for

easy drain flow.

2 Do not make drain piping like the

following.

* The feature can be changed according to

type of model.

Drain pan

Drain

hose

Leakage

checking

Connecting area

drain hose

Leakage

checking

Downward slope

Do not raise

Water

leakage

Accumulated

drain water

Air

Waving

Water

leakage

Tip of drain hose

dipped in water

Water

leakage

Ditch

Less than

50 mm gap

INSTALLATION

ENGLISH

Installation of ﬁlters

1 Pull out the 3M Filter from the separately

packed plastic bag.

2 Detach the two nitto tapes from the filter.

3 Insert the filter into the filter case.

4 Detach two nitto tapes from the plasma

filter.

3M Filter

Plasma Filter

INSTALLATION

ENGLISH

Wiring Connection

- Connect the wires to the terminals on the control board individually according to the outdoor

unit connection.

- Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of

indoor unit respectively.

Terminal block of indoor unit

Terminal block of outdoor unit

1(L) 2(N) 3(A) 4(B)

Indoor power input

IDU IDU

Outdoor unit

Indoor unit

Central controller

SODU SODU

DRY1

DRY2

GND

INTERNET

12 V

The Power cord connected to the unit should be selected according to the following

specifications.

After the confirmation of the above conditions, prepare the wiring as follows:

1) Never fail to have separate power specially for the air conditioner. As for the method of

wiring, follow the circuit diagram pasted on the inside of control box cover.

2) Provide a circuit breaker switch between power source and the unit.

3) The screw which fasten the wiring in the casing of electrical fittings are liable to come loose

from vibrations to which the unit is subjected during the course of transportation. Check

them and make sure that they are all tightly fastened. (If they are loose, it could give rise to

burn-out of the wires.)

4) Confirm the Specification of power source

5) Confirm that electrical capacity is sufficient.

6) Be sure that the starting voltage is maintained at more than 90 percent of the rated voltage

marked on the name plate.

7) Confirm that the cable thickness is as specified in the power sources specification.

(Particularly note the relation between cable length and thickness.)

8) Do not install the leakage breaker in a place which is wet or moist.

Water or moist may cause short circuit.

9) The following troubles would be caused by voltage drop-down.

- Vibration of a magnetic switch, damage on the contact point there of, fuse breaking,

disturbance to the normal function of a overload protection device.

- Proper starting power is not given to the compressor.

WARNING

Make sure that the screws of the terminal are free from looseness.

CAUTION

INSTALLATION

ENGLISH

DIP Switch Setting

Indoor Unit

Outdoor Unit

In case that the products meet specific conditions, “Auto addressing” function can start

automatically with the improved speed by turning the DIP switch #3 of the outdoor unit and

resetting the power.

* Specific conditions:

- All names of the indoor units are ARNU****4

- The serial number of Multi V super IV (outdoor units) is after October 2013,

For Multi V Models, DIP switch 1, 2, 6, 8 must be set OFF.

Function Description Setting Off Setting On Default

SW1 Communication N/A (Default) - - Off

SW2 Cycle N/A (Default) - - Off

SW3 Group Control

Selection of Master

or Slave

Master Slave Off

SW4

Dry Contact

Mode

Selection of Dry

Contact Mode

Wired/Wireless remote

controller

Selection of Manual or

Auto operation Mode

Auto

Off

SW5 Installation

Fan continuous

operation

Continuous operation

Removall

- Off

SW6 Heater linkage N/A - - Off

SW7

Ventilator

linkage

Selection of

Ventilator linkage

Linkage Removal

Working

Off

Vane selection

(Console)

Selection of up/down

side Vane

Up side+Down side

Vane

Up side Vane

Only

Region selection

Selection tropical

region

General model Tropical model

SW8 Etc. Spare - - Off

DIP switch 7 segment

Outdoor Unit PCB Outdoor Unit DIP Switch

CAUTION

INSTALLATION

ENGLISH

Group Control Setting

Group Control 1

n Wired remote controller 1+Standard Indoor Units

Some products have no DIP switch on PCB. It is possible to set indoor units to Master or Slave

by using the wireless remote controller instead of DIP switch.

For the details of the setting, please refer to the manual of the wireless remote controller.

1. It is possible to 16 indoor units(Max.) by one wired remote controller.

Set only one indoor unit to Master, set the others to Slave.

2. It is possible to connect with every type of indoor units.

3. It is possible to use wireless remote controller at the same time.

4. It is possible to connect with Dry Contact and Central controller at the same time.

- The Master indoor unit is possible to recognize Dry Contact and Central Controller only.

5. In case that any error occurs at indoor unit, the error code is displayed on the wired remote

controller.

It is possible to control the other indoor units except the error units.

n DIP Switch in PCB

GND

Signal

12 V

Master Slave Slave Slave

Display Error Message

Only connect serial signal and

GND lines between indoor units.

LGAP Network System

Master

① Master Setting

- No. 3 Off

② Slave Setting

- No. 3 On

Outdoor Unit DIP Switch

INSTALLATION

ENGLISH

GND

Signal

12 V

Slave

Master

Donʼt connect serial 12 V line

LGAP Network System

Master

Master Master

Display Error Message

Group Control 2

n Wired remote controllers+Standard Indoor Units

* It is possible to connect indoor units since Feb. 2009.

* It can be the cause of malfuctions when there is no setting of master and slave.

* In case of Group Control, it is possible to use following functions.

- Selection of operation, stop or mode

- Temperature setting and room temperature check

- Current time change

- Control of flow rate (High/Middle/Low)

- Reservation settings

- It is not possible at some functions.

* It is possible to control 16 indoor units(Max.) with the master wired remote control.

* Other than those, it is same with the Group Control 1.

Page is loading ...

LG ARNU15GSBL4 User manual

Brand: LG

Model: ARNU15GSBL4

Category: Split-system air conditioners

Type: User manual

Download PDF

report

LG ARNU15GSBL4 User manual

LG ARNU15GSBL4 User manual

Related papers

Other documents