OWNER’S MANUAL
High Power
Speaker System
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
RK8
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
MFL69941713
1 Getting Started
Getting Started2
Getting Started
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufcient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NOTICE: For safety marking information including
product identication and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
Getting Started 3
Getting Started
1
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
Check the specication page of this owner’s manual
to be certain of the current requirements.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result
in electric shock or re. Periodically examine the
cord of your device, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of
the device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
This device is equipped with a portable battery or
accumulator.
How to Safely remove the batteries or the battery
pack from the equipment:
To Remove the old batteries or battery pack, follow
the assembly steps in reverse order. To prevent
contamination of the environment and bring on
possible threat to human and/or animal health, the
old batteries or the battery pack must be put in an
appropriate container at designated collection points.
Do not dispose of batteries or battery pack together
with other waste. It is recommended that you use
local, free reimbursement systems batteries or
battery packs, (may not be available in your area). The
batteries or the battery pack should not be exposed
to excessive heat such as sunshine, re or the like.
CAUTION: No naked ame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
~
Refers to alternating current (AC).
0
Refers to direct current (DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
Table of Contents4
Table of Contents
1 Getting Started
2 Safety Information
6 Unique Features
7 Playable file Requirement
7 – Music file requirement
7 – Compatible USB Devices
7 – USB device requirement
8 Top panel
10 Rear panel
11 Carrying the unit
2 Connecting
12 Power Connection
13 Charging Battery
14 Optional Equipment Connection
14 – PORT. IN Connection
14 – Listening to music from your portable player
14 – USB Connection
3 Operating
15 Basic Operations
15 – USB Operations
16 – Auto Play
17 – Selecting a folder and
an MP3/WMA file
18 Playback Effect
18 – DJ EFFECT
18 – SCRATCH
18 – DJ PRO
19 – DJ LOOP
19 – TEMPO
19 – MIX
20 – AUTO SYNC
21 Using BLUETOOTH® wireless technology
21 – Listening to music stored on the Bluetooth
devices
22 – Bluetooth connection lock
(BLUETOOTH LOCK)
24 Using the Music Flow Bluetooth App
24 – About “Music Flow Bluetooth” App
24 – Install “Music Flow Bluetooth” App onto
Your Bluetooth Device
25 – Activate Bluetooth with “Music Flow
Bluetooth” App
Table of Contents 5
1
2
3
4
5
26 Radio Operations
26 – Listening to the radio
26 – Improving poor FM reception
26 – Presetting the Radio Stations
26 – Deleting all the saved stations
27 Sound adjustment
27 – Setting the sound mode
27 – Setting the USER EQ
28 Advanced Operations
28 – Recording to USB1
30 Other Operations
30 – Displaying file information
(ID3 TAG)
30 – DEMO
30 – Using HEADPHONE MODE
31 – Using Microphone
33 – LIGHTING
34 – Auto power down
34 – AUTO POWER On
35 – Auto function change
36 LG Sound Sync
37 WIRELESS PARTY LINK Connection
4 Troubleshooting
38 Troubleshooting
5 Appendix
39 General specifications
40 Trademarks and Licenses
40 Maintenance
40 – Handling the Unit
Getting Started6
Getting Started
1
Unique Features
BLUETOOTH®
Listens to music stored on your Bluetooth device.
Portable In
Listens to music from your portable device.
(MP3, Notebook, etc.)
Playback effects
Listens to music with various sound and playback
effects.
USB Direct Recording
Records music to your USB device.
Music Flow Bluetooth
Music Flow Bluetooth is an app designed to let you
take control of some of LG’s latest audio devices.
(page 24)
LG Sound Sync
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
Getting Started 7
Getting Started
1
Playable file
Requirement
Music file requirement
MP3/WMA le compatibility with this unit is limited
as follows.
y Sampling frequency: within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
y Bit rate: within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
y Maximum les: 2,000
y Maximum folders: 200
y File extensions: “.mp3”/ “.wma”
y Certain MP3/WMA les may not be played
depending on the type or format of the le.
Compatible USB Devices
y MP3 Player : Flash type MP3 player.
y USB Flash Drive :
Devices that support USB2.0 or USB1.1.
y The USB function of this unit does not support all
USB devices.
USB device requirement
y Devices which require additional program
installation when you have connected it to a
computer, are not supported.
y Do not extract the USB device while in operation.
y For a large capacity USB, it may take longer than a
few minute to be searched.
y To prevent data loss, back up all data.
y If you use a USB extension cable or USB hub, the
USB device is not recognized.
y Using NTFS le system is not supported.
(Only FAT (16/ 32) le system is supported.)
y This unit recognizes up to 2,000 les.
y External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
y USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
y Some USB may not work with this unit.
Getting Started8
Getting Started
1
Top panel
a SIDE A/1
USB 1 Port
You can play sound les by connecting the USB device.
DJ SCRATCH / SEARCH & MULTI knob (1)
- Turns clockwise or counterclockwise to make scratch
sound.
- Searches a le or folder.
- Selects lighting mode.
- Chooses a preset number.
C / V (Skip/Search)
- Skips backward or forward.
- Searches for a section within a le.
- Selects the radio stations.
N (Play / Pause)
- Starts or pauses playback.
- Selects stereo/mono.
OK / INFO
- Selects a folder when searching a le.
- Press and hold the OK/INFO button to see
information about your music. An MP3 le often
come with ID3 tag. The tag gives the Title, Artist,
Album or Time information.
- Press and hold the OK/INFO button to see Bluetooth
device name of the unit in BLUETOOTH READY.
- Press and hold the OK/INFO button to see the name
of connected all Bluetooth device in Bluetooth mode.
SEARCH
Searches to the next/prevoius le or next/prevoius
folder by pressing SEARCH repeatedly. (USB 1 only)
DJ LOOP
Selects DJ LOOP mode (USB 1 only).
(DJ LOOP mode can use during USB playback.)
b PRESET
Press to store /search / delete radio stations.
(Chooses a preset number of a radio station with
DJ SCRATCH / SEARCH & MULTI knob.)
c H/P MODE
Press to select a headphone monitor mode.
d ANTENNA (FM)
e H/P VOLUME
Adjusts headphone’s volume.
f < (Headphone) jack
PORT. (Portable) IN jack
g 1 (Standby)
Turns the power on or off.
h USB REC / DEMO
- Records to USB.
- To stop Recording, press and hold for 3 seconds.
- In power off status, if you press USB REC / DEMO,
show DEMO mode.
i LIGHTING
- Selects the lighting effects.
- Press and hold to turn on / off the Flash Lighting.
j / CLUB, / DRUM, / USER (DJ PRO)
Selects CLUB, DRUM or USER sound effect to mix.
(If you want to use USER, you have to register a source
with “Music Flow Bluetooth” app.)
g h k l n omi j
w
f p
q
r
s
t
u
va
b
c
d
e
x
y1
z
Getting Started 9
Getting Started
1
1, 2, 3, 4, 5, 6, 7, 8 (DJ PRO PAD)
Press a desired sound pad.
k DJ EFFECT LEVEL
Selects a desired DJ EFFECT LEVEL
BASS / MIDDLE / TREBLE (USER EQ)
Selects the sound effect created by your own.
l Display window
m AUTO DJ / REPEAT
Selects the AUTO DJ mode or listens to the les
repeatedly or randomly.
n F (Function)
Selects the function and input sources.
Input source / Function Display
USB USB 1 / USB 2
Portable input PORTABLE
Bluetooth BLUETOOTH
LG Sound Sync (Wireless) LG TV
Radio RADIO (FM)
o 3 WIRELESS LINK
- Selects MAIN or OTHER on WIRELESS PARTY LINK
mode.
- Enable or disable WIRELESS PARTY LINK mode.
p CHARGE
Battery charging indicator
q MIC (Microphone) 1 / 2 jack
r MIC (Microphone) VOLUME
Adjusts microphone volume.
s ECHO
Selects ECHO mode.
t VOCAL EFFECTS
Selects VOCAL EFFECTS mode.
u VOICE CANCELLER
You can reduce the vocal tones during music playback
from various input sources.
v SIDE B/2
USB 2 Port
- You can play sound les by connecting the USB
device.
- You can charge the mobile device through this port.
y
The mobile device can be charged only in standby
mode.
y
Some of the mobile devices may not be charged.
,
Note
DJ SCRATCH / SEARCH & MULTI knob (1)
- Turns clockwise or counterclockwise to make scratch
sound.
- Searches a le or folder.
- Selects lighting mode.
- Chooses a preset number.
C / V (Skip/Search)
- Skips backward or forward.
- Searches for a section within a le. (USB 2 only)
N (Play / Pause)
Starts or pauses playback. (USB 2 only)
OK / INFO
- Selects a folder when searching a le.
- Press and hold the OK/INFO button to see
information about your music. An MP3 le often
come with ID3 tag. The tag gives the Title, Artist,
Album or Time information.
- Press and hold the OK/INFO button to see Bluetooth
device name of the unit in BLUETOOTH READY.
- Press and hold the OK/INFO button to see the name
of connected all Bluetooth device in Bluetooth mode.
SEARCH
Searches to the next/prevoius le or next/prevoius
folder by pressing SEARCH repeatedly (USB 2 only).
DJ LOOP
Selects DJ LOOP mode (USB 2 only).
(DJ LOOP mode can use during USB playback.)
w MIX
Mixes audio sound.
x TEMPO A / B
Adjusts TEMPO in USB function.
MASTER VOL.
Adjusts speaker volume.
y CROSS FADER
Adjusts the sound volume of mixing les when using
MIX on by pressing the MIX.
z SOUND EFFECT / BASS BLAST
- Chooses sound impressions.
- Press and hold to select BASS effect directly.
DJ EFFECT
Selects a desired DJ EFFECT.
USER EQ
Selects the sound effect created by your own.
KEY CHANGER
Changes the key to suit your vocal range.
1 AUTO SYNC
When using MIX, you can synchronize the tempo of
audio les being played in USB 1 and USB 2 by pressing
AUTO SYNC.
Getting Started10
Getting Started
1
Rear panel
a AC in socket
Fully charge the device before using.
,
Note
b Battery ON / OFF switch
Switches the battery ON or OFF
(Battery can be charged even when this unit is in
off (OFF) status.)
a b
Getting Started 11
Getting Started
1
Carrying the unit
The unit has strap so you can easily move the unit.
1. Fit a strap in the hook of the unit.
2. Adjust the strap length.
y
Be careful it does not drop the unit when you
carry it.
y
Carry the unit, after then disconnect the
connected cables.
y
Do not place the unit in an unstable position.
Place the unit at a safe distance from a child’s
reach.
y
Be careful so that the unit does not fall
down. Otherwise it may result in malfunction
and cause personal injury and/or property
damage.
>
Caution
Connecting12
Connecting
2
Power Connection
Connect this unit to the power supply with the
supplied AC power cord.
1. Connect the supplied AC power cord to this unit.
2. Plug the AC power cord into an AC outlet.
3. Turn ON/OFF Switch on (ON).
y
If the battery level is very low, this unit does
not turn on even if you turn ON/OFF switch
on (ON).
y
When the battery level is low, this unit
displays LOW BATTERY PLEASE CHARGE
frequently. And if the battery level becomes
even lower, this unit turns off automatically.
y
Previous setting may not be saved when you
turn ON/OFF switch off (OFF).
y
Previous setting may not be saved when the
unit’s power is shut off due to low battery.
,
Note
AC power cord
a
b
2 Connecting
Connecting 13
Connecting
2
Charging Battery
This unit has a built-in battery.
- By connecting AC power, battery will start
charging.
- If Battery charging indicator is in red, this means
that battery is charging now.
- The red LED goes off if the battery is fully charged.
- If the battery is low, ‘LOW BATTERY PLEASE
CHARGE’ is blinking 3 times per minute on a
display window and red LED is blinking continually.
- Charge battery for about 14 hours before you
start using this unit for the rst time.
y
Operating time is approx. 10 hours.
(Based on fully charging the battery,
continuous playback using 50 % volume level
and lighting off status, EQ: Standard).
It may vary depending on the battery status
and operational conditions.
y
If you are listening to the music while
charging, it will take longer to charge.
y
Charge the battery fully during the
recommended time after discharge.
,
Note
Connecting14
Connecting
2
Optional Equipment
Connection
PORT. IN Connection
Connect an output (earphone or line out) of portable
device (MP3 or PMP etc) to the PORT. IN
(3.5 mm) connector.
.
Portable cable
MP3 player etc.
Listening to music from your
portable player
The unit can be used to play music from many types
of portable player or external device.
1. Connect the portable player to the PORT. IN
connector of the unit.
2. Turn the power on by pressing
1
.
3. Press F to select PORTABLE function.
4. Turn on the portable player and start it playing.
Automatically switches to the PORTABLE
function when you connect the portable device
to the PORT. IN connector.
,
Note
USB Connection
Connect a USB device (or MP3 player, etc.) to the
USB ports on the unit.
USB device
Removing the USB device from the unit :
1. Choose a different function.
2. Remove the USB device from the unit.
,
Note
3 Operating
Operating 15
Operating
3
Basic Operations
USB Operations
1. Connect the USB device to the USB port.
2. Select USB function by pressing F on the unit.
To Do this
Playback Press
N
on the unit.
Pause
Press
N
on the unit during
playback.
Searching
for a section
within a le
Press and hold
C
/
V
on the unit
during playback and release it at the
point you want to listen to.
Skipping to
the next/
previous le
Press
V
on the unit to go to the
next le.
Playing less than 2 seconds, press
C
on the unit to go to the previous
le.
Playing after 3 seconds, press
C
on the unit to go to the beginning of
the le.
Playing
repeatedly or
randomly
Press
AUTO DJ / REPEAT
on the unit
repeatedly. Refer to the note for
details about the display change.
y
The display changes in the following order.
USB
AUTO DJ RANDOM
AUTO DJ SEQUENTIAL
REPEAT ONE
REPEAT FOLDER
REPEAT ALL
RANDOM
OFF
y
REPEAT function can be used after AUTO DJ
function display changed.
y
Even after restarting the unit or switching
one function to another, you can listen to
music from the point where it’s last been
played.
y
The next le name is displayed every 30
seconds. (Except RANDOM play, AUTO DJ
RANDOM play, the last le of playlist, etc.)
y
Auto DJ: Auto DJ blends the end of one song
into the beginning of another for seamless
playback.
It equalizes volume across les for
uninterrupted playback.
y
AUTO DJ mode does not support searching
for a section within a le.
y
AUTO DJ is not supported in the music le
whose length is less than 60 seconds.
,
Note
Operating16
Operating
3
Auto Play
When USB is inserted,
- If you press
N
on the SIDE A/1 of the unit, the
function is changed to USB 1 and playback starts.
(Except Bluetooth / Tuner Function).
- If you press
N
on the side SIDE B/2 of the unit, the
function is changed to USB 2 and playback starts.
(except MIXER ON mode)
y
When USB is inserted
- Function is changed to USB 1 if
C
/
V
,
SEARCH on the SIDE A/1 of the unit is
pressed. (Except Bluetooth/Tuner Function)
- Function is changed to USB 2 if
C
/
V
, SEARCH on the SIDE B/2 of the unit
is pressed. (Except MIXER ON mode)
,
Note
Operating 17
Operating
3
Selecting a folder and
an MP3/WMA file
1. Press SEARCH and rotate
DJ SCRATCH / SEARCH & MULTI
until a desired file
appears. You can also search a folder if you press
SEARCH again.
2. Press OK / INFO or
N
to play the selected file.
When you search a folder, press OK / INFO to
select a file in the folder, then press OK / INFO or
N
again. The selected file is played.
y
USB Folders / Files are recognized as below.
y
If there is no le in a folder, the folder will not
appear.
y
Folders will be presented as the following
order;
ROOT
FOLDER 1 FOLDER 3
FOLDER 7 FOLDER 8 FOLDER 5
FOLDER 6
y
File will be played from
$
le No.1 to
$
le
No.14 one by one.
y
Files and folders will be presented in order
recorded and may be presented differently
according to the record circumstances.
y
*ROOT : The rst screen you can see when a
computer recognize the USB is “ROOT”.
,
Note
Operating18
Operating
3
Playback Effect
The unit supports various sound and playback effects
: DJ EFFECT, SCRATCH, DJ PRO, DJ LOOP, TEMPO, MIX,
AUTO SYNC.
DJ EFFECT
It allows you to enjoy DJ EFFECT such as Flanger/
Phaser/Wah/Delay sound effect.
1. Press DJ EFFECT on the unit to select a desired
DJ EFFECT (FLANGER, PHASER, WAH, DELAY,
OFF).
2. Turn DJ EFFECT LEVEL controller on the unit
clockwise or counterclockwise to adjust the
DJ EFFECT level between 0 to 15.
y
The DJ EFFECT mode is displayed for 3
seconds when a DJ EFFECT key on the unit is
inputted.
y
The current gage level is displayed when
adjusting gage.
y
If the function changed or the unit is turned
off and on, DJ EFFECT mode with DJ EFFECT
is turned off.
,
Note
SCRATCH
You can output and mix the sound effects of the
SCRATCH.
Rotating
DJ SCRATCH / SEARCH & MULTI
on the unit
to mix the scratch sound.
- You can hear effect of scratch sound depending
on the direction in which you rotate
DJ SCRATCH / SEARCH & MULTI
on the unit.
DJ PRO
It allows you to mix CLUB, DRUM or USER sound
effect. Each mode has up to 8 sounds effect.
1. Press and hold DJ PRO (/ CLUB, / DRUM or
/ USER) on the unit to select a desired DJ PRO
sound effect.
2. Press DJ PRO pad (1, 2, 3, 4, 5, 6, 7, 8) of
desired sound on the unit.
y
If you want to use USER, you have to register
a source with “Music Flow Bluetooth” app.
If the source is not register to USER,
“EMPTY” or “NO SOUND” appears on the
display window.
y
Initial DJ Pro mode is CLUB sound effect.
y
DJ Pro mode is displayed for 3 seconds when
you press DJ PRO ( / CLUB, / DRUM or
/ USER) on the unit.
y
The DJ PRO sound is mixed when you press
DJ PRO pad (1, 2, 3, 4, 5, 6, 7, 8) on the
unit.
y
The currently playing DJ PRO sound is
stopped and the selected DJ PRO sound
outputs if you press a different DJ PRO pad
(1, 2, 3, 4, 5, 6, 7, 8) on the unit while
DJ PRO sound is playing.
,
Note
Operating 19
Operating
3
DJ LOOP
The certain section (about 1 sec) of sound is
repeatedly played. (USB Only)
During playback, press and hold DJ LOOP on the unit
at the point you want. And you can cancel DJ LOOP
function by releasing it.
This function is released after operating 10
times or releasing DJ LOOP on the unit.
,
Note
TEMPO
You can adjust the Tempo for USB function 1 or 2
from 50 (MIN) to 150 (MAX).
Rotate TEMPO A to adjust the tempo for USB 1.
Rotate TEMPO B to adjust the tempo for USB 2.
The tempo is set as 100 if you turn the unit off.
,
Note
MIX
You can mix audio sounds.
1. Press MIX. ‘MIXER ON’ is displayed.
Select a desired Function for SIDE A/1 and play it.
Mix is available in all functions except USB 2.
2. During playback, insert a USB device in
USB 2 port and play it. SIDE B/2 is fixed as USB 2
function.
3. Move the CROSS FADER to adjust the sound
volume of mixed sound. Move it to the left to
lower the volume of SIDE B/2 and move it to the
right to lower the volume of SIDE A/1.
y
In MIXER ON mode,
- You can adjust the Tempo for USB function 1 or
2.
- If you press
C
/
V
,
N
on the unit, it works
only for each side.
- You can use H/P MODE. (page 30)
y
If you turn off the unit in the middle of mixing
process, MIX mode turns to OFF.
,
Note
Operating20
Operating
3
AUTO SYNC
When using Mixing, you can synchronize the tempo
of audio les being played in USB 1 and USB 2 by
pressing AUTO SYNC.
To stop it, press AUTO SYNC twice.
y
The tempo of music being played in USB 1 is
synchronized to that in USB 2.
y
TEMPO A doesn’t work when AUTO SYNC is
on.
y
If function is changed, AUTO SYNC function is
cancelled.
y
In case of below, AUTO SYNC error may occur
depending on the sound source.
- The silent section in the beginning of the track.
- Intro or bridge section in which few musical
instruments appear.
- In cases where playback speed or tempo of the
song changes.
- In case that the data for BPM is provided in real
time, not the beginning of the song.
y
If the song is being played too fast or slow,
press and hold AUTO SYNC.
‘AUTO SYNC/RE-ANALYZING’ is displayed.
y
AUTO SYNC is available only when USB 1 is
selected for SIDE A/1 and USB 2 is selected
for SIDE B/2 in MIXER ON mode and both are
being played.
,
Note
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
