Poulan Pro 1000E User manual

ENGLISH ESPAÑOL

FRANÇAIS

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury .

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en le-

siones graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le

faire pourrait entraîner des blessures graves.

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

1000E

Electrolux Home Pro duc ts, Inc.

104 W arren Road

Augusta, GA 30907

R Trademark

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1-800-554- 6723

www.weedeater.com

IDENTIFICATION OF SYMBOLS

DANGER! This lawn edger

can be dangerous! Careless or

improper use can cause

serious or even fatal injury.

Read and understand the

instruction manual before

using the lawn edger.

Always wear appropriate ear protection, eye protection and head protection.

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions must al-

ways be followed to reduce the risk of fire and

serious injury . Read and follow all instructions.

This power unit can be dangerous! Operator

is responsible for following instructions and

warnings on unit and in manual. Read entire

instruction manual before using unit! Be thor-

oughly familiar with the controls and the prop-

er use of the unit. Restrict the use of this unit

to persons who have read, understand and

will follow the instructions and warnings on

the unit and in the manual. Never allow chil-

dren to operate this unit.

SAFETY INFORMATION

ON THE UNIT

OPERATOR SAFETY

DANGER: RISK OF CUT. KEEP

HANDS AND FEET AWAY FROM BLADE

AND CUTTING AREA. Do not attempt to

clear away cut material or hold material to be

cut when the blade is in motion. Make sure

powerhead is stopped and spark plug wire is

disconnected (or powerhead is disconnected

from power source) when removing jammed

material from the cutting blade. Do not grab or

hold attachment by the cutting blade.

S Dress properly. Always wear safety glasses

or similar eye protection when operating, or

performing maintenance on your unit (safety

glasses are available). Eye protection should

be marked Z87.

S Always wear face or dust mask if operation is

dusty.

S Always wear heavy, long pants, long sleeves,

boots, and gloves.

S Always wear foot protection. Do not go bare-

foot or wear sandals.

S Secure hair above shoulder length. Secure

orremovelooseclothingorclothingwith

loosely hanging ties, straps, tassels, etc.

They can be caught in moving parts.

S Being fully covered also helps protect you

from debris and pieces of toxic plants thrown

by spinning blade.

S Stay alert. Do not operate when you are tired,

ill, upset, or under the influence of alcohol,

drugs, or medication. Watch what you are do-

ing; use common sense.

S Wear hearing protection.

S Never start or run inside a closed room or

building. Breathing exhaust fumes can kill.

S Keep handles free of oil and fuel.

S Only operate unit with handlebar installed.

S Keep hands and feet away from cutting area.

S Never direct discharge of materi al toward by-

standers nor allow anyone near the area of

operation. Use care in directing discharge to

avoid glass enclosures, automobiles, and the

like.

FUEL SAFETY (for gas powerheads)

S Mix and pour fuel outdoors.

S Keep away from sparks or flames.

S Use a container approved for fuel.

S Do not smoke or allow smoking near fuel or

the powerhead.

S Avoid spilling fuel or oil. Wipe up all fuel spills

before starting the powerhead.

S Move at least 10 feet (3 meters) away from

fueling site before starting powerhead engine.

S Stop engine and allow to cool before remov-

ing fuel cap.

S Remove fue l cap slowl y.

ELECTRICAL SAFETY (for electric

powerheads)

WARNING: Avoid a dangerous envi-

ronment. To reduce the risk of electrical

shock, do not use in rain, in damp or wet loca-

tions, or around swimming pools, hot tubs,

etc. Do not expose to snow , rain, or water to

avoid the possibility of electrical shock. Do

not handle extension cord plug or unit with wet

hands.

S Use only a voltage supply as shown on the

nameplate of the unit.

S Avoid dangerous situations. Do not use in

presence of flammable liquids or gases to

avoid creating a fire or explosion and/or caus-

ing damage to unit.

S Avoid dangerous environments. Do not use

in unventilated areas or where dust or explo-

sive vapors can build up.

S To reduce the risk of electrical shock, use ex-

tension cords specifically marked as suitable

for outdoor appliances. The electrical rating of

the cord must not be less than the rating of the

unit. The cord must be marked with the suffix

“W-A” (in Canada, “W”). Make sure your ex-

tension cord is in good condition. Inspect ex-

tension cord before use and replace if dam-

aged. An undersized extension cord will

cause a drop in line voltage resulting in loss of

power and overheating. If in doubt, use the

next heavier gauge. The smaller the gauge

number , the heavier the cord.

S Do not use multiple cords.

S The powerhead may have a polarized plug

(one blade is wider than the other); if so, it will

require the use of a polarized extension cord.

The appliance plug will fit into a polarized ex-

tension cord only one way. If the plug does

not fit fully into the extension cord, reverse the

plug. If the plug still does not fit, obtain a cor-

rect polarized extension cord. A polarized ex-

tension cord will require the use of a polarized

wall outlet. This plug will fit into the polarized

wall outlet only one way. If plug does not fit

fully into the wall outlet, reverse the plug. If it

still does not fit, contact a qualified electrician

to install the proper wall outlet. Do not change

the equipment plug, extension cord recep-

tacle, or extension cord plug in any way.

S Do not attempt to repair unit. Inspect the insu-

lation and connectors on the powerhead and

extension cord before each use. If there is

any damage, do not use until damage is re-

paired by your authorized service dealer .

S Do not pull or carry by cord; do not use cord

as a handle, close a door on cord, or pull cord

around sharp edges or corners. Keep cord

away from heated surfaces. Do not unplug by

pulling on cord. To unplug, grasp the plug, not

the cord.

S Do not use the powerhead if the switch does

not turn the unit on and off properly. Have the

unit repaired by your authorized service deal-

er .

S Keep the extension cord clear of operator and

obstacles at all times. Do not expose cords to

heat, oil, water, or sharp edges.

S Avoid any body contact with any grounded

conductor, such as metal fences, or pipes, to

avoid the possibility of electric shock. Don’t

handle plug or unit with wet hands.

S Do not use with damaged cord or plug. If pow-

erhead is not working as it should, has been

dropped, damaged, left outdoors, or dropped

into water, return it to your authorized service

for repair.

S Ground Fault Circuit Interrupter (GFCI)

protection should be provided on the circuit or

outlet to be used for the powerhead. Recep-

tacles are available having built-in GFCI

protection and may be used for this measure

of safety.

Your powerhead should be double insulated

to help protect against electric shock. Double

insulation construction consists of two sepa-

rate “layers” of electrical insulation instead of

grounding. Tools and appliances built with a

double insulation system are not intended to

be grounded. Safety precautions must be ob-

served when operating any electrical tool.

The double insulation system only provides

added protection against injury resulting from

an internal electrical insulation failure.

WARNING: All repairs to an electric

powerhead, including housing, switch, motor ,

etc., must be diagnosed and repaired by qual-

ified service personnel. Replacement parts

for a double insulated appliance must be iden-

tical to the parts they replace. A double insu-

lated appliance is marked with the words

“double insulation” or “double insulated”. The

symbol

(square within a square) may also

be marked on the appliance. Failure to have

the unit repaired by your authorized service

dealer can cause the double insulation con-

struction to become ineffective and result in

serious injury.

UNIT/MAINTENANCE SAFETY

WARNING: Disconnect powerhead

spark plug (or disconnect powerhead from

power source) before performing mainte-

nance.

S Inspect entire unit before each use. Replace

damaged parts. Check for fuel leaks. Make

sure all fasteners are in place and securely

fastened.

S Maintain unit according to recommended pro-

cedures.

S Throw away blades that are bent, warped,

cracked, broken, or damaged in any other

way. Replace parts that are cracked,

chipped, or damaged before using the unit.

S Use only recommended We ed Eater® parts

and accessories. Never use wire, wire

rope, string, flailing devices, etc.

S Be sure blade stops turning when engine

idles (see CARBURETOR ADJUST-

MENTS section of powerhead manual).

S Remove the blade before making carburetor

adjustments. Hold the unit by hand. Do not

make carburetor adjustments from the blade

side of the unit.

S Keep others away when making carburetor

adjustments.

S Never start the unit with the clutch housing re-

moved. The clutch can fly off and cause seri-

ous injury .

S Have all maintenance and service not ex-

plained in this manual performed by an autho-

rized service dealer .

S If blade strikes a foreign object, follow these

steps: stop unit and disconnect spark plug

wire (or disconnect from power source), in-

spect for damage, and repair any damage be-

fore resuming operation of the unit.

EDGING SAFETY

W ARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, string, etc.)

which can be thrown by the blade or can wrap

around the shaft.

S Keep others including children, animals, by-

standers, and helpers at least 50 feet (15 me-

ters) away. Stop the unit immediately if you

are approached.

S Hold the unit firmly with both hands.

S Keep firm footing and balance. Do not over-

reach or stand on unstable surfaces.

S Always keep the wheel in contact with the

ground.

S Keep all parts of your body away from the

blade and muffler .

S Always push the unit slowly over the ground.

Stay alert for uneven sidewalks, holes in the

terrain, large roots, etc.

S Do not force the unit. Use only for jobs ex-

plained in this manual. Use only for edging.

Do not abuse unit. Do not use in rain or wet

lo ca t i o n s.

S To reduce the risk of fire, do not allow exces-

sive grass, leaves, or grease to accumulate

on the attachment.

S Objects struck by the cutting member can

cause serious injuries to persons. The lawn

should always be carefully examined and

cleared of all objects prior to edging.

S Never operate without blade shield in place.

Allow blades to stop

before removing them

from the cut.

WARNING:

Blades can throw objects violently.

D You can be blinded or injured.

D Wear safety glasses and boots.

WARNING:

Hazard zone for thrown objects.

D Blades can throw objects violently.

D Others can be blinded or injured.

D Keep people and animals 50 feet

(15 m) away.

Boots

Blades move

momentarily

after the

trigger is

released.

WARNING:

Blades move momentarily after the

trigger is released.

D The blades can seriously cut you or

others.

D Allow blades to stop before

removing them from the cut.

Safety

Glasses

Thrown

Objects

Instruction

Manual

Safety Decals

W ARNING:

Read Instruction Manual.

D Follow all warnings and instructions.

D Failure to do so can result in

serious injury.

TRANSPORTING AND STORAGE

S Do not grasp or hold exposed blade.

S Stop powerhead before leaving work area.

S Allow powerhead and gearbox to cool before

storing or transporting it in a vehicle.

S Store unit and fuel in area where fuel vapors

cannot reach sparks or open flames from wa-

ter heaters, electric motors or switches, fur-

naces, etc.

S Store attachment so blade cannot accidental-

ly cause injury.

S Store attachment indoors, out of reach of chil-

dren.

If situations occur which are not covered in

this manual, use care and good judgment. If

you need assistance, call 1-800-554-6723.

SPECIAL NOTICE: Exposure to vibra-

tions through prolonged use of gasoline pow-

ered hand tools could cause blood vessel or

nerve damage in the fingers, hands, and

joints of people prone to circulation disorders

or abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel dam-

age in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek med-

ical attention. An anti-vibration system does

not guarantee the avoidance of these prob-

lems. Users who operate power tools on a

continual and regular basis must monitor

closely their physical condition and the condi-

tion of this unit.

SAVE THESE INSTRUCTIONS

STANDARDS: This edger attachment is Listed by Underwriter’s Laboratories, Inc., in ac-

cordance with UL Standard 1602, “Gasoline--Engine--Powered, Rigid--Cutting--Member,

Edgers and Edger Trimmers,” only when used with the following models:

31cc Powerhead (with trimmer attachment) 31WG............................

ASSEMBLY

WARNING: If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

TOOLS REQUIRED

S Hex wrench (provided)

HANDLEBAR ASSEMBLY

DANGER: RISK OF CUT. To avoid

serious injury, the barrier portion of the han-

dlebar must be installed as shown on the up-

per shaft of the powerhead to provide a barrier

between operator and the spinning blade. At-

tach handlebar mounting bracket above ar-

row on safety warning decal on the upper

shaft (powerhead end of unit). Ensure han-

dlebar is positioned on mounting bracket at

the end of the arrow on the handlebar decal.

NOTE: T wo mounting brackets are included

with this attachment. Both brackets are pro-

vided to adapt this attachment for use with pow-

erheads that have either a 1″ (2.5 cm) diamete r

or a 7/8″ (2.2 cm) diameter upper shaft. The

correct bracket must be used to ensure that the

handlebar is mounted securely to the upper

shaft before use.

Screw

Mounting

Bracket

Handlebar

Bracket Cover

1. Place the mounting bracket over the upper

shaft above the arrow on the safety label.

Be sure to use the correct mounting brack-

et for either the 1″ (2.5 cm) or 7/8″ (2.2 cm)

diameter upper shaft.

2. Position one of the bracket covers under

the upper shaft and align the mounting

bracket and the bracket cover screw

holes. Insert two screws into the screw

holes.

3. Secure the mounting bracket by tightening

the screws with the hex wrench.

4. Locate the decal on the handlebar. This

decal includes an arrow. Position the han-

dlebar with the mounting bracket at the

end of the arrow .

5. Position the second bracket cover over

the handlebar. Align the mounting bracket

and the bracket cover screw holes. Again

make sure the handlebar is at the end of

the arrow.

6. Insert two screws and hand tighten only.

Be sure the handlebar is installed cor-

rectly; then, tighten each screw securely

with the hex wrench.

OPERATION

KNOW YOUR EDGER ATTACHMENT

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR EDG-

ER A TT ACHMENT. Compare the illustrations with your attachment to familiarize yourself with the

location of the various controls and adjustments. Save this manual for future reference.

Depth Adjustment Knob

Blade Shield

Gearbox

Wheel

Edger Blade

Shaft

Hanger

BLADE

The BLADE is designed to cut sod.

DEPTH ADJUSTMENT KNOB

The DEPTH ADJ USTMENT KNOB is used

to adjust the wheel for blade cutting depth.

OPERATING THE COUPLER

Your powerhead is equipped with a coupler

which enables optional attachments to be

installed. The optional attachments are:

MODEL:

Cultivator 2000T....................

Blower 3000B......................

Brushcutter 4000C..................

WARNING: Always disconnect pow-

erhead spark plug (or disconnect powerhead

from power source) before removing or instal-

ling attachments.

REMOVING ATTACHMEN T

CAUTION:

When removing or installing at-

tachments, place the powerhead and attach-

ment on a flat surface for stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Knob

LOOSEN

TIGHTEN

Upper Shaft

Lower

Attachment

2. Press and hold the locking/release button.

ocking

Release

Button

Coupler

Upper Shaft

Lower Attachment

3. While securely holding the upper shaft,

pull the attachment straight out of the cou-

pler.

INSTALLING ATTACHMENT

1. Remove the shaft cap from the attachment

(if present) and discard.

2. Position locking/release button of attach-

ment into guide recess of upper shaft cou-

pler.

Coupler

Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

3. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

4. Before using the unit, tighten the knob se-

curely by turning clockwise.

INSTAL L ING ATTACHMENT

HANGER

An attachment hanger is provided for storage

when attachment is not in use.

To install hanger on attachment:

1. Remove the shaft cap from the attachment

(if present) and discard.

2. Press and hold the locking/release button.

3. Push hanger onto the attachment until the

locking/release button snaps into the hole.

OPERA TING POSITION

Heavy Shoes

Long Pants

Eye Protection

ALWAYS WEAR:

When operating unit, stand as shown and

check for the following:

S W ear eye protection and heavy clothing.

S Keep right arm slightly bent with right hand

holding the trigger handle of powerhead.

S Keep left arm extended with left hand hold-

ing the handlebar.

S Keep unit below waist level.

S Adjust edger wheel for proper cut depth.

WARNING: Never attempt to adjust

the edger wheel when the unit is in operation.

Always stop the powerhead, wait until the

blade stops turning, and disconnect the spark

plug (or disconnect powerhead from power

source) before making adjustments.

EDGING

As you become familiar with use of your edger

attachment, you will be able to determine your

own operating pace. Conditions such as

depth of cut and material being cut will regu-

late the speed and time required for your edg-

ing job.

S Allow the engine to warm up before you begin

edging.

S Increase the engine speed before placing the

blade in the cut. For best results, run the en-

gine at full throttle while cutting.

S Al wa ys work goi n g away from peop l e an d

solid obj ect s such as walls, large stones,

trees, automobiles, etc.

S Be careful when edging near trees or valuable

plants. The high speed metal blade may cut

roots and cause damage to the plants.

S If the blade stalls, immediately move the unit

back slightly to allow the blade to restart. If the

blade continues to stall, stop the engine, dis-

connect the spark plug, and inspect for block-

age or damage.

WARNING: Keep the blade area

clean. Always release the throttle trigger,

move the powerhead ON/OFF switch to the

OFF position, disconnect the spark plug (or

disconnect powerhead from power source),

and make sure the blade has completely

stopped turning before cleaning.

SETTING THE EDGING DEPTH

WARNING: Never attempt to adjust

the cut depth when the engine is running. Al-

ways release the throttle trigger, wait until the

blade stops turning, move the powerhead

ON/OFF switch to the OFF position, and dis-

connect spark plug (or disconnect from pow-

er source) before making adjustments.

Depth Adjustment

Knob

1. Loosen the depth adjustment knob.

2. Slide the wheel to the desired position.

S Raising the wheel will increase the cut-

ting depth.

S Lowering the wheel will decrease the

cutting depth.

3. Tighten the depth adjustment knob se-

curely .

MAINTENANCE

WARNING: Always stop unit and dis-

connect spark plug wire (or disconnect pow-

erhead from power source) before performing

maintenance.

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

S Blade Shield -- Discontinue use of edger if

blade shield is damaged.

CHECK FOR LOOSE

FASTENERS AND PARTS

S Blade nut

S Fasteners

INSPECT AND CLEAN UNIT AND

DECALS

S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

S Wipe off unit with a clean dry cloth.

BLADE MAINTENANCE

WARNING: The blade will continue

to spin after the engine stops or after the

throttle trigger has been released. To avoid

serious injury, make sure the blade has

stopped coasting and disconnect the spark

plug (or disconnect powerhead from power

source) before performing work on the blade.

WARNING: Always replace a blade

that is bent, warped, cracked, broken, or

damaged in any other way. Never attempt to

straighten and reuse a damaged blade. Use

only specified replacement blade. Wear pro-

tective gloves when handling or performing

maintenance on the blade to help avoid injury.

S The blade is reversible. When the cutting

edge on one side becomes worn, turn the

blade over (see BLADE REPLACEMENT

in the SERVICE AND ADJUSTMENTS

section).

S Check blade for flatness periodically. Lay

the blade on a flat surface to inspect for flat-

ness. Throw away a blade that is not flat.

SERVICE AND ADJUSTMENTS

BLADE R EPLACEMENT

W ARNING: The blade will continue to

spin after the engine stops or after the throttle

trigger has been released. To avoid serious

injury, make sure the blade has stopped

coasting and disconnect the spark plug (or

disconnect powerhead from power source)

before performing work on the blade.

W ARNING: Wear protective gloves

when handling or performing maintenance on

the blade to avoid injury. The blade is sharp and

can cut you even when it is not moving.

1. To remove the blade, align hole in the dust

cup with the hole in the side of the gearbox

by rotating the blade.

2. Insert a small screwdriver into aligned

holes. This will keep the shaft from turning

while loosening the blade nut.

Screwdriver

3. While holding the screwdriver in position,

remove blade nut by turning clockwise.

4. Remove both washers, and the blade from

the blade shaft.

Blade shield

Blade

Washers

Blade nut

Blade

Shaft

5. Install new blade onto blade shaft.

6. Reinstall both washers and blade nut

(counterclockwise).

7. Tighten blade nut firmly with a wrench

while holding screwdriver in position.

8. Remove the screwdriver .

9. Turn blade by hand. If the blade binds

against the shield, or appears to be un-

even, the blade is not centered, and you

must reinstall.

STORAGE

WARNING: Perform the following

steps after each use:

S Allow attachment and gearbox to cool be-

fore storing or transporting.

S Store attachment with blade shield in place.

Position attachment so that any sharp ob-

ject cannot accidentally cause injury .

S Store the attachment in a dry , well venti-

lated area out of the reach of children.

SEASONAL STORAGE

Prepare attachment for storage at end of sea-

son or if it will not be used for 30 days or more.

If your edger attachment is to be stored for a

period of time:

S Clean the entire attachment.

S Inspect the blade shield area and clean any

dirt, grass, leaves, or debris that has col-

lected. Inspect the blade and blade shield; re-

place a blade that is bent, warped, cracked,

broken or damaged in any other way.

S Lightly oil external metal surfaces.

S Apply a coating of oil to the entire surface of

the blade; wrap it in heavy paper or cloth.

S Check entire attachment for loose screws

or nuts. Replace any damaged, worn or

broken parts.

S At the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

LIMITED WARRANTY

ELECTROLUX HO ME PRODUCTS, INC.,

warrants to the original purchaser that each

new Weed Eater® brand gasoline tool or at-

tachment is free from defects in material and

workmanship and agrees to repair or replace

under this warranty any defective gasoline

product or attachment as follows from the

original date of purchase.

2 YEARS-- Parts and Labor, when used for

household purposes.

90 DAYS -- Parts and Labor, when used for

commercial, professional, or income produc-

ing purposes.

30 DAYS -- Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does not

cover damage or liability caused by improper

handling, improper maintenance, or the use

of accessories and/or attachments not spe-

cifically recommended by ELECTROLUX

HOME PRODUCTS, INC., for this tool. Addi-

tionally, this warranty does not cover tune-

ups, spark plugs, filters, cutting line, or rotat-

ing head parts that will wear and require

replacement with reasonable use during the

warranty period. This warranty does not cov-

er predelivery setup or normal adjustments

explained in the instruction manual.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATETOSTATE.NOCLAIMSFORCON-

SEQUENTIAL O R OTHER DAMAGES WILL

BE ALLOWED, AND THERE ARE NO

OTHER EXPRESS WARRANTIES EX-

CEPT THOSE EXPRESSLY STIPULATED

HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of ELECTROLUX HOME PROD-

UCTS, INC., is to continuously improve its

products. Therefore, ELECTROLUX HOME

PRODUCTS, INC., reserves the right to

change, modify, or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice or obliga-

tion to any purchaser.

Poulan Pro 1000E, 530164833, PPB1000E, Trimmer 1000E User manual

Related papers

Other documents