LG Uplus LAP255U User manual

Type
User manual
Z-Wave Certification App User Guide
1
This guide documents explain how to use Z-Wave Certification Application to test Z-Wave
functionalities. Z-Wave Certification Application only can be run on android framework, and
use IoTService(android service, automatically started when android boot up)
So, if android don’t boot up completely, this application couldn’t be run properly.
2
Overview & Limitations
1. Turn On Device & Enter Android home.
b. Connect Power cable.
3
Run Application
a. Connect HDMI cable to any TV or Monitor.
c. Wait some minutes until android boot up.
d. Push “O” button on remote controller to enter android home.
2. How to run Z-Wave Certification
a. move : Settings -> Apps -> System Apps -> Run Z-Wave Certification
4
Run Application
b. Select Z-Wave Certification
c. Select “Open”
5
Run Application
6
Inclusion & Exclusion
1. How to include Z-Wave devices
a. Select Things” in the left MENU
b. Select “bridge” (lgzwave:bridge:zwavebridge)
- command list will be appeared on the right list.
This Chapter describe how to add node for inclusion and remove for exclusion.
7
Inclusion & Exclusion
c. Select addThingon the right list
8
Inclusion & Exclusion
d. When you select AddThing, Send Command Dialog popped up.
e. And then Check Command & Push “SEND” Button
f. after that, command will be sent, and wait until attached another Z-Wave node
9
Inclusion & Exclusion
g. If Node is attached successfully, “success comment” is added Status list.
10
Inclusion & Exclusion
g. you can also check in the Thing list by selecting Things on the left MENU
11
Inclusion & Exclusion
2. How to exclude Z-Wave devices
a. Select Things” in the left MENU
b. Choose “bridge
12
Inclusion & Exclusion
c. Select lgzwave_bridge_zwavebridge_removeThing
d. Check Command & Push SEND Button
e. push exclude button of Node wanted to exclude.
(in case of GasLock, “-button push for 5 sec.)
13
Inclusion & Exclusion
f. Check “Success Comment”
14
Inclusion & Exclusion
g. And also you can see what the Node is excluded on Things list
15
Send & Receive Command
1. Send Basic Command & Receive
a. Choose specific Thing on Things List
This Chapter describe how to send command to Z-Wave Node. at first, describe full sequence
with basic Command, and another command also can be sent like basic Command.
16
Send & Receive Command
b. Commands List are appeared on the right list
c. Select a Command that you want to call.(at this time, Choose basicCall)
17
Send & Receive Command
d. “Send Command Dialog” is popped up.
18
Send & Receive Command
e. Choose Command(BASIC_SET, BASIC_GET)
19
Send & Receive Command
e. Choose BASIC_GET & PUSH “SEND” Button
20
Send & Receive Command
e. Check Success comment & Check value
f. Now Current Value : FF
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

LG Uplus LAP255U User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI