2. justanswer
  3. RAF5654-5410006 Adjusting Front or Rear Glass Slide Tilt Sunroof Panel

justanswer RAF5654-5410006 Adjusting Front or Rear Glass Slide Tilt Sunroof Panel Operating instructions

  • Hello! I've reviewed the repair instructions for adjusting the sunroof panel on Mini models such as F56 2-Door HT (F56), R50, R53, R56, R60, R61, F54, F55, and F60. The document covers special tools, installation notes, height and distance adjustments, and tightening torques. I'm ready to assist with any questions you have about this process.
  • What special tools are needed for adjusting the sunroof?
    Can the microencapsulated screws be reused?
    How long should screw connection be completed?
    Do I need an assistant for making adjustments?
    What is the tightening torque for the glass slide/tilt sunroof panel screws?
2018 Mini Cooper S 2-Door HT (F56) L4-2.0L Turbo (B46M)
ADJUSTING FRONT OR REAR GLASS SLIDE/TILT SUNROOF PANEL [REP-REP-
RAF5654-5410006 - V.3]
Repair instruction
Adjusting front or rear glass slide/tilt sunroof panel
54 13 004 | REP-REP-RAF5654-5410006 - V.3
54 13 004 Adjusting front or rear glass slide/tilt sunroof panel
Special tools required:
009315
009340
Installation note:
Microencapsulated screws (Loctite) must
be replaced and may be reused.not
Screw connection must be completed
within 20 min. (start of hardening)
Microencapsulated screws must be
retightened.
not
When using nuts multiple times, first clean
the thread.
Note:
Make the adjustment with an assitant.
Perform setting with fully closed glass slide/tilt
sunroof.
Height adjustment
Front edge of glass slide/tilt sunroof panel at front 0 to 1mm under roof edge
Rear edge of front glass slide/tilt sunroof panel 0 to 1.5mm above rear glass slide/tilt sunroof panel
Rear edge of glass slide/tilt sunroof panel 0 to 1mm above roof edge
Height adjustment:
Note:
Front glass slide/tilt sunroof panel must be
adjusted first.
Check height of glass slide/tilt sunroof panel (1) in
relation to body(2) with special tool .009315
Press glass slide/tilt sunroof panel(1) at front and
rear upwards or downwards until ideal position is
reached.
Distance setting:
Use special tool check that the gap between
the glass slide/tilt sunroof panel and body is the
same.
009340
Slide special tool or similar between gasket
and insert. It must be possible to slide the card
against the same level of resistance.
009340
Slide glass slide/tilt sunroof panel towards front or
rear until ideal position is reached.
Adjusting glass slide/tilt sunroof panel at front:
Carry out the following step on one side first and then
the other (first left, then right or vice versa):
Loosely screw in Torx screws(1) on left/right
until glass slide/tilt sunroof panel(2) can just
still be shifted
Shift glass slide/tilt sunroof panel(2) as
required
Make sure all screws are tightened down.
Tightening torque:
54124AZ Type Thread
Tightening
specificati
ons
Dime
nsion
4
A
Z
Glass
slide/t
ilt
sunro
of
panel
to
mech
anics
R50 / R53
/ R56
Renew
screws. 4 Nm
R60 / R61
/ F54 /
F55 / F56
/ F60
M5x6
Renew
screws.
4,5
Nm
Repeat procedure on other side.
Glass slide/tilt sunroof panel rear setting:
Carry out the following step on one side first and then
the other (first left, then right or vice versa):
Loosely screw in torx screws(1) on left/right
until glass slide/tilt sunroof panel(2) can just
still be shifted
Shift glass slide/tilt sunroof panel(2) as
required
Make sure all screws are tightened down.
Tightening torque:
54124AZ Type Thread
Tightening
specificati
ons
Dime
nsion
4
A
Z
Glass
slide/t
ilt
sunro
of
panel
to
mech
anics
R50 / R53
/ R56
Renew
screws. 4 Nm
R60 / R61
/ F54 /
F55 / F56
/ F60
M5x6
Renew
screws.
4,5
Nm
Repeat procedure on other side.
Check function and adjustment.
Carry out .initialization
/