NOMA LEVI Owner's manual

USER MANUAL

READ AND SAVE THESE INSTRUCTIONS

Levi

48" LED Ceiling Fan

PRODUCT NO. 052-9605-4

TABLE OF CONTENTS

2

01. SAFETY/CAUTIONS

02. TOOLS REQUIRED

03. EXPLODED VIEW

04. ELECTRICAL SAFETY

05. ASSEMBLY

06. OPERATION

07. TROUBLESHOOTING

08. DYNAMIC BLADE BALANCING KIT

09. MAINTENANCE

10. WARRANTY & DISPOSAL

4

6

7

10

12

19

21

23

25

26

3

SAFETY / CAUTIONS

•

TO REDUCE THE RISK OF ELECTRIC SHOCK, ENSURE ELECTRICITY HAS

BEEN TURNED OFF AT THE CIRCUIT BREAKER OR FUSE BOX BEFORE

BEGINNING.

ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND

LOCAL ELECTRICAL CODES. ELECTRICAL INSTALLATION SHOULD BE

PERFORMED BY A QUALIFIED LICENSED ELECTRICIAN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO

NOT USE THIS FAN WITH ANY SOLID-STATE FAN-SPEED CONTROL

DEVICE. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE

SCREWS PROVIDED WITH THE OUTLET BOX.

THE OUTLET BOX AND SUPPORT STRUCTURE MUST BE SECURELY

MOUNTED AND CAPABLE OF RELIABLY SUPPORTING A MINIMUM OF

50 LB (22.7 KG). USE ONLY UL-LISTED OUTLET BOXES MARKED “FOR FAN

SUPPORT.”

THE FAN MUST BE MOUNTED WITH A MINIMUM OF 6´11˝ (2.1 M) FROM

THE TRAILING EDGE OF THE BLADES TO THE FLOOR.

AVOID PLACING OBJECTS IN THE PATH OF THE BLADES.

TO AVOID PERSONAL INJURY OR DAMAGE TO THE FAN AND OTHER

ITEMS, BE CAUTIOUS WHEN WORKING AROUND OR CLEANING THE

FAN.

DO NOT USE WATER OR DETERGENTS WHEN CLEANING THE FAN

OR FAN BLADES. A DRY DUST CLOTH WILL BE SUITABLE FOR MOST

CLEANING.

AFTER MAKING ELECTRICAL CONNECTIONS, SPLICED CONDUCTORS

SHOULD BE TURNED UPWARD AND PUSHED CAREFULLY UP INTO

THE OUTLET BOX. THE WIRES SHOULD BE SPREAD APART WITH THE

GROUNDED CONDUCTOR AND THE EQUIPMENT-GROUNDING

CONDUCTOR ON ONE SIDE OF THE OUTLET BOX AND THE

UNGROUNDED CONDUCTOR ON THE OTHER SIDE OF THE OUTLET BOX.

ALL SET SCREWS MUST BE CHECKED AND RE-TIGHTENED WHERE

NECESSARY BEFORE INSTALLATION.

4

WARNING: CHEMICAL BURN HAZARD. KEEP BATTERIES AWAY FROM

CHILDREN. THIS PRODUCT CONTAINS A LITHIUM BUTTON/COIN CELL

BATTERY. IF A NEW OR USED LITHIUM BUTTON/COIN CELL BATTERY IS

SWALLOWED OR ENTERS THE BODY, IT CAN CAUSE SEVERE INTERNAL

BURNS AND CAN LEAD TO DEATH IN AS LITTLE AS 2 HOURS. ALWAYS

COMPLETELY SECURE THE BATTERY COMPARTMENT. IF THE BATTERY

COMPARTMENT DOES NOT CLOSE SECURELY, STOP USING THE

PRODUCT, REMOVE THE BATTERIES, AND KEEP IT AWAY FROM

CHILDREN. IF YOU THINK BATTERIES MIGHT HAVE BEEN SWALLOWED OR

PLACED INSIDE ANY PART OF THE BODY, SEEK IMMEDIATE MEDICAL

ATTENTION.

A) THE CELLS SHALL BE DISPOSED OF PROPERLY, INCLUDING KEEPING

THEM AWAY FROM CHILDREN; AND

B) EVEN USED CELLS MAY CAUSE INJURY.

01

•

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT” WITH THE SCREWS PROVIDED WITH

THE OUTLET BOX.

WARNING: TO AVOID RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES) OR THE BRACKETS

WHILE BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT OF 50 LB (22.7 KG) OR LESS”

AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.

MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHT FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY

NEED TO BE REPLACED. DUE TO THE COMPLEXITY OF THIS FAN, A

QUALIFIED LICENSED ELECTRICIAN IS STRONGLY RECOMMENDED FOR

INSTALLATION.

ATTENTION: PLEASE ENSURE LED BULBS’ TOTAL WATTAGE IS ALWAYS

•

BELOW 70 W!

5

02

TOOLS REQUIRED

INSTALLATION PREPARATION

Flat-head

screwdriver

Cross-head

screwdriver

Safety glasses Pliers

Wire cuttersElectrical tape Stepladder Wire strippers

6´11˝

(2.1 m)

30”

(76 cm)

To prevent personal injury and

damage, ensure that the hanging

location allows the blades a

clearance of 6´11˝ (2.1 m) from the

floor and 30” (76 cm) from any wall or

obstruction.

This fan can be mounted with a

downrod on a regular (no-slope) or

vaulted ceiling. Other installations,

such as flush mount, are not

available for this fan.

Blade edge

Downrod

installation installation

Flush mount

Vaulted

ceiling angle

is not to

exceed 18°.

6

02 03

EXPLODED VIEW

PACKAGE CONTENTS

01.

02.

03.

04.

05.

06.

07.

08.

09.

10.

HANGER BRACKET

CANOPY

CANOPY COVER

DOWNROD STAND COVER

DOWNROD, HANGER PIN

& LOCK PIN

FAN MOTOR ASSEMBLY

FAN BLADES (3 PCS)

SWITCH HOUSING

LED LIGHT KIT

GLASS SHADE

11.

12.

13.

REMOTE CONTROL UNIT

A. Transmitter

B. Receiver

C. CR2032 battery

D. 2 Expansion anchors

2 screws

E. 4 Wire connector

Balance kit

A. 1 Plastic clip

B. 2 Balancing weight

PARTS PACK CONTAINING:

01

02

08

03

04 09

05

06

07

10

13

x 2

x 1

2x wood screws

2x washes

2x screws

Cable Hardware Bag

1x screw

1x washer

1x split washer

x 2 x 2 x 4

A B

E

11

DC

12

5g

x 1

x 2

7

EXPLODED VIEW

DETAIL

01. CLEVIS PIN

02.

03.

04.

05.

06.

07.

08.

09.

FAN BLADE

LIGHT KIT

HANGER BRACKET

HANGER BALL

CANOPY

CANOPY COVER

DOWNROD

DOWNROD STAND

COVER

10.

11.

12.

13.

14.

HAIRPIN CLIP

COLLAR

FAN MOTOR

ASSEMBLY

SWITCH HOUSING

GLASS SHADE

03

8

03

01

02

04

05

06

07

08

11

09

10

12

13

14

9

ELECTRICAL SAFETY

Instructions

•

01.

02.

03.

04.

Making the Electrical Connections

•

Read all safety information and installation instructions before

you begin to install the fan and save instructions.

All set screws of the fan must be checked and re-tightened

where necessary before installation.

To reduce the risk of personal injury, do not bend the blade

brackets when installing the brackets, balancing the blades

or cleaning the fan. Do not insert foreign objects between

rotating fan blades.

Before changing the fan direction, turn off the fan and wait for

the fan blades to stop completely.

The safeguards provided by these safety instructions and by

the separate installation instructions are not meant to cover all

possible conditions and situations that may occur. It must be

understood that common sense, caution and care are factors

which cannot be built into this product. These factors must be

supplied by the person(s) installing, caring for and operating

the fan.

WARNING: To avoid risk of electric shock, be sure to shut off

power at the main fuse or circuit breaker box before installing

or servicing this fixture. Turning off the electrical power by using

the light switch is not sufficient to prevent electric shock.

To reduce the risk of injury, install the fan so that the blades are

at least 6´ 11˝ (2.1 M) above the floor and at least 30” (76 cm)

from the tip of the blades to the wall.

10

04

•

mount the outlet box marked “ACCEPTABLE FOR FAN

To reduce the risk of flre, electric shock, or personal injury,

SUPPORT” and use mounting screws provided with the outlet

box.

The installation must be in accordance with national

electrical code, ANSI/NFPA 70-1999 and local codes. If you

are unfamiliar with the methods of installing electrical wiring,

seek the services of a qualified licensed electrician.

injury, mount to outlet box and use mounting screws provided

WARNING: To reduce the risk of fire, electric shock, or personal

with the outlet box.

IMPORTANT: Before you begin installing the fan, carefully read

all information on the separate sheet “SAFETY INSTRUCTIONS”

as well as the following “Installation Steps”. If in doubt, consult

a qualified electrician.

NOTE: The fan weight is 11 lb 14 oz (5.4 kg). Be sure the outlet

box you are using is securely attached to the building structure

and can support the full weight of the fan. Failing to do so can

result in serious injury.

11

Turn OFF the electric circuit at the main

fuse of circuit breaker box.

01

Securely attach the mounting bracket to

an outlet box marked “ACCEPTABLE FOR

FAN SUPPORT” using the supplied outlet

box screws with spring washers.

02

03 04

ASSEMBLY

Mounting

bracket

Outlet box

screw

Spring

washer

Outlet

box

Set scew

Hanger ball

Downrod

Hairpin clip

Clevis pin

Remove the hanger ball portion from

the downrod/hanger ball assembly by

loosening the set screw in the hanger

ball until the ball falls freely down the

downrod. Remove the pin from the

downrod, then remove the hanger ball.

Retain the pin and hanger ball for

reinstallation.

Remove the hairpin clip and clevis pin

from the bottom of the downrod. Retain

the pin and clip for reinstallation for next

step.

12

05

Canopy

05 06

Canopy

cover

Downrod

stand cover

07

Collar

Clevis pin

Set screw

Hairpin clip

Loosen the two set screws. Route the

wires and safety cable through the

downrod. Slide the downrod into the

collar on the top of the motor. Install the

clevis pin by aligning the holes in the

collar with the holes in the downrod.

Secure clevis pin with hairpin clip. Install

and tighten the two previously removed

set screws.

Thread the motor wires and cable wire

through the downrod stand cover,

canopy cover and canopy.

Reinstall the hanger ball on the downrod

as follows. Route the wires and safety

cable through the hanger ball. Position

the pin through the two holes in the

downrod and align the hanger ball so

the pin is captured in the groove in the

top of the hanger ball. Pull the hanger

ball up tight against the pin. Securely

tighten the set screw in the hanger ball.

A loose set screw could cause fan wobble.

Downrod

Hanger

ball

13

ASSEMBLY

For added security attach safety cable

from fan “J” hook in outlet box. Secure

looping zip tie through safety cable and

“J” hook. Tighten zip tie securely.

09

Safety

cable “J”

hook

Tighten

zip tie

Zip

tie

08

Hang the fan on hanger bracket, and

make sure the slot of hanger ball is

snapped into the clip of hanger

bracket exactly.

NO

OK

10

The safety cable must be installed into

the house structure beams using a 3”

lag screw. Make sure that when the

safety cable is fully extended the lead

wires are longer than the cable and no

stress is placed on the lead wires.

14

05

IMPORTANT: If you are not sure if the electrical outlet box and

fan are grounded, contact a licensed electrician for advice.

They must be grounded for safe operation.

WARNING: To avoid possible electric shock, be sure electricity

is turned off at the main fuse box before wiring.

Once the connection has been made, the receiver inserts

into the drop rod hanging bracket. The canopy comes up to

cover the receiver and bracket.

Wiring Instructions

•

DO NOT CUT THIS - As this is the antenna

VIEW AFTER INSTALLATION

Between Fan & Receiver

Connect the pin connectors together, refer to next page for

details.

•

Between Receiver and Mains

Connect the black live wire marked ”AC POWER L” from the

receiver to the live wire (typically black) from the outlet box.

•

Connect the white neutral wire marked ”AC POWER N” from

the receiver to the neutral wire (typically white) from the outlet box.

•

Connect the green ground wire from the mounting bracket

and hanger ball to the ground wire bare or green from the

outlet box.

•

15

AC IN N(WHITE)

AC IN L(BLACK)

YELLOW ("TO MOTOR U")

RECEIVER

YELLOW ("TO MOTOR U")

RED ("TO MOTOR W")

BLUE ("FOR LIGHT L")

WHITE ("FOR LIGHT N")

RED ("TO MOTOR W")

BLUE ("FOR LIGHT L")

WHITE ("FOR LIGHT N")

GREEN (Ground wire)

Ground wire

GREY ("TO MOTOR V") GREY ("TO MOTOR V")

GREEN (Ground wire)

WHITE

BLACK

16

ASSEMBLY

INSTRUCTIONS - CONTINUED

Half-tighten one hanger bracket screw,

remove one hanger bracket screw,

then push the canopy upwards and let

the hanger bracket screw head come

through the key hole slot, then rotate the

canopy counter-clockwise until canopy

is secured. Now, tighten hanger bracket

screws. Finally, push the canopy cover

upward, then turn it counter-clockwise

until it is secure.

11

Hanger

bracket

Hanger

bracket screw

Canopy

screw

Key

hold slot

Canopy

cover

Tighten fan blades to motor assembly by

using blade screws.

12

Remove one of the mounting screws

on mounting plate of motor assembly,

then loosen the other two. Attach the

switch housing to the mounting plate

on the motor assembly by placing the

keyhole slots from the switch housing

onto the two protruding mounting

screw heads. Then put back the screws

and tighten them.

13 Mounting

screw

Switch

housing

1

2

17

Connect the 2-pin connectors from the light

kit to the 2-pin connectors from the motor

assembly. Remove one of the screws on

switch housing then loosen the other two.

Attach the light kit to switch housing using

the two key slots in the light kit. Replace the

screw and tighten all switch housing screws

securely.

14

Light kit

1

2

3

05

Secure the shade to switch housing by

twisting in a clockwise direction. Do not

over-tighten.

15

18

OPERATION

01

Slide the transmitter out of the holder.

02

Select a location to install the holder.

Attach the holder with two screws

provided.

03

Be sure to use a tool to depress the

hook to remove the battery door.

DO NOT forcibly open.

04

To make fan operational, install a

CR2032 3 V battery (included). Replace

the battery door.

WARNING: CHEMICAL BURN HAZARD. KEEP

BATTERY AWAY FROM CHILDREN.

05

19

06

IC STATEMENT

This device contains license-exempt transmitter(s)/receiver(s) that comply with

lnnovation, Science and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

Turn fan on/off and select fan speed.

LED indicated light

ON/OFF the fan

Turn up the speed of the fan

Turn down the speed of the fan

Direction of the fan (reverse switch)

Timing control of the fan

3V CR2032 battery X 1

CCT: 3000 K/4000 K/5000 K

Short press: ON/OFF the light

Long press: Adjust the brightness of the light

Restore power to ceiling fan and test for

proper operation. The fan remote controls

the fan settings.

05

8

9

1h 3h 6h

20

Page is loading ...

NOMA LEVI Owner's manual

NOMA LEVI Owner's manual

in other languages