MediaHub
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
2
Table of Contents
Product Introduction ..................................................................3
Safety Precaution Information ....................................................4
Definitions ..................................................................................6
Electrical Requirements .............................................................7
Care and Maintenance ..............................................................7
Installation and Usage ...............................................................8
Packing List................................................................................ 8
Standard Installation Instructions............................................... 9
Configuring the Guest-Access Technique................................. 9
Standard Auto-Sensing Feature............................................... 10
Using MediaHub HD ................................................................ 10
Using Stereo Bluetooth…......................................................... 11
TV/STB Supported Installation –
For Implementing Auto-Switching Feature...............................13
Samsung North America .......................................................... 14
Panasonic North America......................................................... 16
Philips North America............................................................... 19
LG North America..................................................................... 21
Enseo Set Top Box................................................................... 23
LodgeNet PPV System ............................................................. 25
Troubleshooting MediaHub HD ...............................................26
How to Access the On-Screen Display.................................... 26
Troubleshooting Protocol Converter Dongle… ........................27
Technical Support
...................................................................... 28
Flush-Mount Cut Measurements
............................................... 29
Assemble Flush-Mount MediaHub HD with Power/Data .......30
Assemble Desktop Housing (DTH-HD01 or DTH-EXT) .........31
Add-On Accessories..........................................................33
iPodDocking Adapter IPODDONGLED60................................ 33
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
3
Product Introduction
Thank you for choosing the TeleAdapt MediaHub for your in-room entertainment or
conference room connectivity needs. MediaHub allows business and leisure
travellers to use the in-room TV display as their personal entertainment or projection
screen for enjoying their personal standard- and high-definition (HD) video games,
music playlists, movies, TV shows, photos, business presentations and more from
their portable electronic devices.
The MediaHub HD™ entertainment panel is unique as it features Stereo Bluetooth®
wireless technology. Hotel guests can pair their A2DP-enabled portable media
player with the MediaHub HD to stream personal music and audio choices through
the in-room TV and speakers, without having to physically connect the device with a
cable. MediaHub HD also features a single-HDMI back-end cable connection to the
TV for a more simple, faster installation process.
Please review this Installation Manual carefully, taking note of important safety,
installation and usage information.
This complete User and Installation Manual is available for download at
www.teleadapt.com.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
4
Safety Precaution Information
When used in the directed manner, this unit has been designed and
manufactured to ensure your personal safety. However, improper use can result
in potential electrical shock or fire hazards. Please read all safety and operating
instructions carefully before installation and use. Be sure to keep these
instructions handy for future reference. Take special note of all warnings listed in
these instructions and on the unit.
The lightning flash with arrowhead symbol within an equilateral is intended to
alert the user to the presence of un-insulated dangerous voltage within the
product enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
Important Safety Instructions
1 | Read these instructions.
2 | Keep these instructions.
3 | Heed all warnings.
4 | Follow all instructions.
5 | Do not use this apparatus near water.
6 | Clean only with dry cloth.
7 | Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8 | Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including amplifiers) that produce heat.
9 | Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete
outlet.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
5
10 | Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles and the point where they exit
from the apparatus.
11 | Only use attachments/accessories specified by the manufacturer.
12 | Use only with the cart, stand, tripod, bracket or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13 | Unplug this apparatus during lightning storms or when unused for
long periods of time.
14 | Refer all servicing to qualified service personal. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15 | The apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
16 | The mains plug used as disconnect device shall remain readily operable.
17 | To reduce the risk of fire or electric shock, do not expose this apparatus
to rain or moisture.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
6
Definitions
A2DP – Advanced Audio Distribution Profile, the
Bluetooth
® protocol that is built
into MediaHub HD for streaming high quality audio wirelessly between devices.
For example, music can be streamed from a mobile smartphone to an in-room
stereo/TV speaker using MediaHub HD as the receiver.
Auto-Sensing – the automatic detection of a device plugged into an audio/video
port of the MediaHub. For example, MediaHub will auto-sense a Composite AV
source when a device is connected to the 3RCA ports and begin playing the
Composite AV Out content. When a laptop is plugged into the PC socket,
MediaHub will detect a PC Video source and switch to play the laptop video.
Auto-Switching – the automatic switching of the TV input away from
regular tuner mode (TV Mode) to the MediaHub’s portable device content
(MediaHub Mode).
Control Cable – MediaHub HD uses serial or game control protocol for
implementing the TV auto-switching feature. Most hospitality TVs support control
protocols through the following ports:
RS232 Serial Port (DB9)
Serial Control Jack (3.5mm)
Ex-Link Serial Control Jack (3.5mm)
RJP (RJ45 LG Remote Jack Pack)
GAME/DATA (RJ12 on TV or STB)
DIP Switches – MediaHub HD has eight (8) DIP Switches located on the rear
of the unit. (Figure 1) These switches must be configured accordingly to allow
appropriate communication between MediaHub and TV/STB. See Installation
& Usage section for DIP Switch setting required for standard installation, and the
TV/STB-Supported Installation section for setting required for specific TV/STB
auto-switching installation.
RS232 – MediaHub HD supports RS-232 serial control protocol for implementing
the TV auto-switching feature. Most hospitality TVs support RS232 protocol through
their RS232 Serial port (circular port with nine pins), or through their 3.5mm Serial
Control port.
Figure 1: DIP switches located on the
rear of the MediaHub HD
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
7
Electrical Requirements
A 120-volt, 60Hz, 15-Amp electrical supply is required for the TA-7650. A
standard duplex (2) 120-volt, 60Hz, 15-Amp electrical supply is required for
the TA-7650 plus TA-7500L.
Care and Maintenance
Though TeleAdapt MediaHubs are designed for durability, they still remain
complex electronic devices. As such, care needs to be taken with how they are
handled. The following are tips to care for your system:
If the MediaHub has visible smudges, fingerprints, or other foreign material,
you can clean it by using a soft clean cloth such as a lens or eyeglass
cleaning cloth.
Slightly dampen a corner of the cloth with water and wipe off the unit
housing to loosen any dirt or foreign material. Using a dry portion of the same
cloth, wipe the housing to dry.
Do not use harsh chemicals, cleaning solvents, or strong detergents to
clean the MediaHub.
Your TeleAdapt MediaHub should never be positioned or installed anywhere
where it could get hit, dropped, or banged around.
Do not drop, knock, or shake the device. Rough handling can harm
internal operations.
Your MediaHub should be dry. Liquids or moisture can cause damage to
internal electronic circuits. If your unit gets wet, immediately remove power
allowing the unit to dry before re-applying power.
Do not store the MediaHub in hot areas. High temperatures can shorten the
life of electronic components and warp or melt certain plastics.
Do not attempt to open the MediaHub gaining access to the internal
infrastructure. Please notify TeleAdapt service and support personnel
regarding return materials authorization policy.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
8
Disposal
The crossed-out wheeled-bin symbol on your product, literature, or packaging
reminds you that in the European Union all electrical and electronic products must
be taken to separate collection at the end of their working life. Do not dispose of
these products as unsorted municipal waste.
Return the products to collection to prevent possible harm to the environment or
human health from uncontrolled waste disposal and to promote the sustainable
reuse of material resources.
Installation and Usage
Packing List(s)
“x” characters denote part numbers that correlate to the power supply variations and product
trim types
TA-7650x-xx-x03
A MediaHub HD Connectivity Panel
B Power Supply with Cable
C Flat-Head Mounting Screws x4
D Cable Ties x4
CAB-76503D5 MediaHub HD Cable Kit (3m)
E HDMI Cable CAB-40683D5
F RS-232 Control Cable CAB-04583D5 (for serial control, see TV/STB-Supported
Installation Instructions)
G Optional DB9-3.5mm Adapter CAB-4067D16 (for serial control, see TV/STB-Supported
Installation Instructions)
TA-7500L-xx-x03 (PowerHub Extender) includes:
H TA-7500 PowerHub unit (Power/Data Panel) with connected Power Supply Cable
I Extender Trim with micro mounting screws
J
Cat5 Ethernet Cable (3m)
K
Additional Flat-Head Mounting Screws x4
A
C
B
E
F
G
D
A
C
B
E
F
K
D
G
J
I
H
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
9
DTH-xxx Desktop Mount Kit also includes:
A Desktop Housing
DTH-HD01 for MediaHub HD
DTH-EXT for MediaHub HD with PowerHub Extender
B
90º HDMI Replacement Cable CAB-40683D5A
C
Rear Door Screws
D
Rubber Tabs
See
Assembling Desktop Housing section
for assembly instructions.
Standard Installation Instructions (for Manual Switch)
1 | While unplugged, ensure MediaHub rear DIP Switches are set to the following
positions
(Pg 6)
: UP - DOWN - UP - UP -- DOWN - DOWN - DOWN - DOWN
2 | Remove the back door of MediaHub HD.
3 |
Connect the HDMI and power supply to rear of the MediaHub HD.
4 |
Connect the HDMI cable to the TV’s HDMI port.
5 | Plug the MediaHub
HD power supply into a wall power socket.
6 | To fully install the MediaHub HD with PowerHub Extender, connect the Cat5
Ethernet cable to the rear of the PowerHub portion and plug other end into an
existing wall Ethernet jack. Plug the PowerHub power supply into a wall power
socket.
Configuring the Guest-Access Technique
Similar to installing a DVD player or other third-party component into a hospitality
in-room entertainment system, allowing guests to access the MediaHub HD plug
ports can be done through one of three common guest-access techniques.
Option 1:
“Channel map” the TV’s HDMI AUX port used to connect MediaHub HD
(e.g., HDMI1) to a number in the VOD/PPV/FTG channel roster. Using the
guest remote control, guests simply change the channel to the number
assigned to MediaHub HD.
Option 2:
Program the guest remote control to make the in-room TV’s HDMI AUX
available to the guest via the INPUT button. Using the guest remote
control, guests simply press the INPUT button to play content from the
MediaHub HD.
Figure 1: Desktop Mount Kit
HDMI
5V
HDMI
5V
TV HDMI IN
1
2
5
4
3
A
C
B
D
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
10
Option 3:
Program the PPV/VOD GUI to offer the in-room TV’s HDMI AUX through
an on-screen prompt. Using the guest remote control, guests simply
follow the on-screen prompts to play content from the MediaHub HD.
Standard Auto-Sensing Feature
MediaHub HD has been engineered with a built-in auto-sensing audio/video
function. Multiple devices may be connected to the MediaHub HD at once. The
connectivity panel will recognize and automatically play content from the most
recently populated AV socket. To switch back to a previously used audio/video
port, press the LED/button above the desired AV socket.
Using MediaHub HD
When in use, MediaHub HD’s LED/buttons located above the sockets will light up notifying
you of which port is in use.
To change devices, plug in a new device using a new socket. TV will automatically play
content from the most recently populated socket. When connecting multiple devices, guests
may toggle between devices by pressing the LED/buttons located above the sockets.
A
Composite Audio/Video (3RCA):
Using a composite cable, provides audio and video
playback through the in-room TV. Compatible with any electric device that can use a
composite connection including iDevices, MP3 player, DVD player, game console, or
digital cameras.
B S-Video: Using an S-Video cable, provides video-only playback through the in-room TV.
Some Super Video-enabled video cameras, laptops, digital cameras and laptops. May
also couple the 2RCA stereo ports (red and white) of the Composite AV to provide paired
audio playback through the in-room TV speakers.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
11
C Mini-Stereo Jack: This 3.5mm stereo jack will provide audio playback through the
in-room TV speakers. Compatible with any electronic media player with a headphone
jack. Use a male-to-male audio cable.
D VGA (RGB): Using a VGA cable, converts the in-room TV into a secondary or mirror
display option for laptop computers.
E HDMI: Using an HDMI cable, provides high definition video and audio playback through
the in-room TV. Compatible with newer generation laptops, smartphones, or digital
video cameras that have an HDMI-out, mini-HDMI out or micro-HDMI out. Also compatible
with non-HDMI devices using an HDMI converter cable such as VGA-to-HDMI or
MDP-to-HDMI.
F USB (5V): Using a USB cable, offers a charging outlet for USB-powered electronics such
as iDevices, smartphones, digital cameras, and more. Note, iPad® product will charge
using 5V power when in sleep mode only.
G Stereo Bluetooth: Converts the in-room TV into a wireless speaker for A2DP-enabled
media players. Plays music or other audio from portable electronics through the in-room
TV speakers without using a cable or wire. Compatible with iDevices, smartphones,
laptops, or other media players that are equipped to use wireless speakers.
Using Stereo Bluetooth (pairing process):
Step 1 – Enable Stereo Bluetooth in your personal media player by selecting
Stereo Bluetooth* ON in your player’s general settings.
* Note: Stereo Bluetooth is not the same Bluetooth technology used to pair a Bluetooth
headset. Media player must be equipped with Stereo Bluetooth, or A2DP (Advanced
Audio Distribution Profile). Consult your device specifications.
Step 2 – Press and hold the MediaHub’s Bluetooth button for five seconds
until a four-digit PIN number appears on the TV screen. The blue LED light
will blink while in “pairing mode.”
Step 3 – Pair your device:
a Select your player’s Bluetooth Device Discovery option screen
b Choose the MediaHub
c Enter the four-digit PIN
d Choose “Connect”
Step 4 – When your device is paired, the LED light will remain lit. Choose your
audio selection and enjoy wireless audio streaming.
Bluetooth Pairing Step 1
Bluetooth Pairing Step 2
Bluetooth Pairing Step 3
Bluetooth Pairing Step 4
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
12
The pairing session will hold until your player is turned off. If you connect
another media device to the MediaHub HD, the new audio/video source will
begin to play through the TV. MediaHub HD will maintain the Stereo Bluetooth
pairing. When done using the second device, simply press the MediaHub HD
Bluetooth LED button to resume playing your Stereo-Bluetooth-enabled player
or smartphone.
MediaHub HD with PowerHub Extender also features:
H/J Power Outlet: Two AC power outlets for convenient power charging. Voltage and
frequency varies by regional model. Outlets do not convert voltages. Ensure voltage and
frequency of source match that of the selected power socket:
US/US: 110V – 60Hz
UK/UK: 220-240V – 50Hz
EU/EU: 220-240V – 50Hz
UK/EU: 220-240V – 50Hz
I RJ45 Internet Jack: Wired Internet access point. Using a CAT5 cable, guest can connect
their computers to the Internet. If this port will remain inactive, an optional cover piece is
available and sold separately (Part # COV-RJ45S01).
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
13
TV/STB Supported Installation
For Implementing Auto-Switching Feature
MediaHub HD can be configured to automatically switch the TV input source to the TV’s
HDMI Auxiliary port once a device is plugged into the panel, without the need to use the
remote control INPUT button, channel map or on-screen prompts. This configuration requires
a serial control connection to a hospitality TV or Tuner Card/Set Top Box that has firmware
integrated with the TeleAdapt MediaHub HD.
The following pages outline instructions are for installing MediaHub HD with a specific brand
TV/STB supported serial control installation.
For hotel room environments that are integrating a TV plus VOD STB, MediaHub
may have direct serial control integration with both the TV serial port and the VOD
serial or data port. Please use the following list of priority connections when
determining which connection you should use to install MediaHub:
#1 Priority – Connect to LodgeNet Game/Data port
#2 Priority – Connect to RJP port (on most LG TVs)
#3 Priority – Connect to VOD STB Serial Control port (such as Enseo)
#4 Priority – Connect to TV Serial Control port
For all noted TV model numbers, “
nn
” denotes the screen size.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
14
▼
HDMI 2
EXLINK
HDMI
5V
▼
Adapter
RS232
Samsung North America
What You Will Need:
- TA-7650 or TA-7650/TA-7500L
MediaHub HD Connectivity Panel
Power Supply Cable
(Note: MediaHub with Power/Data Extender model includes
TWO power supplies – one for media panel and one for power panel)
Ethernet Cable (for MediaHub with Power/Data Extender model only)
- MediaHub Cable Kit
HDMI Cable (3m)
RS-232 Cable
DB9-3.5mm Adapter
- Samsung Hospitality Display & Remote Control
Samsung Direct-to-TV Installation Instructions
Follow cable connection instructions illustrated in Figure 1. Then configure the TV and
MediaHub HD according to the model-specific requirements on the following page.
For Samsung 2011 North America Models
For Samsung LED and LCD Hospitality Series displays with EXLINK serial port (factory-
level firmware)
MediaHub HD DIP Mode B7:
UP-DWN-UP-UP -- DWN-UP-UP-UP
MediaHub HD Firmware Version: 1.23+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Using Samsung remote control, enter the menu by pressing
<MUTE>, <1>, <1>, <9>, <ENTER>. Ensure the following is selected:
Hotel Mode = ON, RJP HDMI Option = HDMI2 and set appropriate SI Vendor.
*If using SI Vendor = ENSEO, please refer to Enseo Installation Instructions section.
For Samsung 2009/2010 North America Models
For Samsung Series 4 LN
nn
B450C4H and LN
nn
B457C6H models with EXLINK serial port
(TV firmware v.1011.1+)
For Samsung Series 5 LN
nn
B550K1H models with EXLINK serial port
(TV firmware v. 1007+)
Figure 1: Samsung direct-to-TV cable
connection diagram.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
15
Samsung 2009/2010 continued:
For Samsung LED Series 4, LED Series 6, LCD Series 3, LED Series 4, LED Series 5 models
with EXLINK serial port (factory-level firmware)
MediaHub HD DIP Mode B7:
UP-DWN-UP-UP -- DWN-UP-UP-UP
MediaHub HD Firmware Version: 1.23+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Using Samsung remote control, enter the menu by pressing
<MUTE>, <1>, <1>, <9>, <ENTER>. Ensure the following is selected:
Hotel Mode = ON and RJP HDMI Option = HDMI2.
For Samsung 2008 North America Models and Older (non-LodgeNet)
For Samsung Series 4 LN
nn
A450C1H and Series 6 LN
nn
A650A1H models with EXLINK
serial port (TV firmware v.1003.8+)
MediaHub HD DIP Mode 57:
DWN-UP-DWN-UP -- DWN-UP-UP-UP
MediaHub HD Firmware Version: 1.23+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Using Samsung remote control, enter the menu by pressing
<MUTE>, <1>, <1>, <9>, <ENTER>. Ensure the following is selected:
Hotel Mode = ON and RJP HDMI Option = HDMI2.
For Samsung North America Models and an External Enseo STB
Follow instructions for Samsung Direct-to-TV Installation according to the
year/model number of your Samsung display. OR, you may install
MediaHub HD’s serial control connection to the Enseo STB. See instructions
for Enseo STB Installation.
For Samsung North America Models and an External PPV STB
Follow Samsung Direct-to-TV installation instructions according to the year/model number of
your Samsung display. Connect the PPV STB AV Out to TV’s HDMI1 port.
For Legacy Samsung + LodgeNet environments, please refer to the LodgeNet STB section.
Or, follow Standard Installation instructions on Page 9 and configure the guest access
technique (channel map, program INPUT button on remote control, or program LodgeNet on-
screen prompt.)
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
16
Panasonic North America
What You Will Need:
- TA-7650 or TA-7650/TA-7500L
MediaHub HD Connectivity Panel
Power Supply Cable
(Note: MediaHub with Power/Data Extender model includes
TWO power supplies – one for media panel and one for power panel)
Ethernet Cable (for MediaHub with Power/Data Extender model only)
- MediaHub Cable Kit
HDMI Cable (3m)
RS-232 Cable
DB9-3.5mm Adapter
- Panasonic Hospitality Display & Remote Control
- IMP/DTB Tuner, if applicable
Panasonic North America Direct-to-TV Installation (Series 20, 30 and 12)
Follow cable connection instructions illustrated in Figure 1. Then configure the TV and
MediaHub HD according to the model-specific requirements below.
Panasonic North America Series 30 and 20 Hospitality Models
For hospitality models with serial control (factory-level firmware)
MediaHub HD DIP Mode BB:
UP-DWN-UP-UP – UP-DWN-UP-UP
MediaHub HD Firmware Version: 1.32+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Go into HOTEL MODE (using Panasonic remote, press <MENU>,
<G>, <Y>, <0>), set MODE=ON, BUTTON LOCK = OFF, TA CONTROL = OFF.
For Series 30, also set CP MODE = YES
* For Panasonic North America Series 20 displays + Legacy OnCommand (OCV) STB
system, TV requires firmware version 1.09. Follow instructions above but set
TA CONTROL = EXTERNAL.
Panasonic Series 30/20 using Internal Terminal Adapter
Note: Panasonic Series 20 displays require firmware version 1.080.
Configure TV: Go into HOTEL MODE (using Panasonic remote, press <MENU>,
<G>, <Y>, <0>), select the following: MODE = ON, TA Control = INTERNAL,
BUTTON LOCK = OFF. For Series 30, also set CP MODE = YES.
Figure 1: Panasonic direct-to-TV cable
connection diagram.
HDMI
5V
▼
HDMI 1
CONTROL
Adapter
RS232
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
17
Panasonic North America Series 20 ProDisplay Models
For Series 20 Professional Display moels with an IMP2000 tuner card and serial control
(factory-level firmware on TV, IMP2000 card requires Enseo firmware patch v.24)
Connect MediaHub HDMI to TV’s native HDMI port, connect RS232/DB9 adapter to IMP’s
3.5mm serial control port.
MediaHub HD DIP Mode BB:
UP-DWN-UP-UP – UP-DWN-UP-UP
MediaHub HD Firmware Version: 1.32+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Go into HOTEL MODE (using Panasonic remote, press <MENU>,
<G>, <Y>, <0>), set MODE=ON, BUTTON LOCK = OFF, TA CONTROL = OFF.
Configure Tuner Card: Press <Channel UP>, <Right Arrow>, <Left Arrow>,
<MUTE> to enter set-up screen. Select PPV = NONE (Tuner Card will reset), set
BAUD rate to 9600 and set Standby Save = OFF.
Panasonic North America Series 12 Models
For TH-nnLRT12U models with serial control (factory-level firmware)
MediaHub HD DIP Mode B5:
UP-DWN-UP-UP – DWN-UP-DWN-UP
MediaHub HD Firmware Version: 1.32+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Go into HOTEL MODE (using Panasonic remote, press <MENU>,
<G>, <Y>, <0>), set MODE=ON, BUTTON LOCK = OFF.
Panasonic North America Series 30/20/12 Models with Enseo HD3000/2000
Follow instructions for Panasonic Direct-to-TV installation according to the model number of
your Panasonic display. OR, you may install MediaHub HD’s serial control connection to the
Enseo STB. See instructions for Enseo STB Installation.
Panasonic North America Series 30/20/12 Models with External PPV STB
Follow Panasonic Direct-to-TV installation instructions according to the model number of your
Panasonic display. Connect the PPV STB AV Out to TV’s HDMI1 port. Connect MediaHub
HD’s HDMI to TV’s HDMI2.
* For Panasonic North America Series 20 displays + Legacy OnCommand (OCV)
STB system, TV requires firmware version 1.09. Follow instructions above but set
TA CONTROL = EXTERNAL.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
18
Panasonic Series 10/11 with IMP- Tuner Card
This installation requires an IMP- Tuner Card in Slot 2/3 and the Panasonic TY-FB10HMD
Dual HDMI Terminal Card in Slot 1. (Figure 1)
MediaHub HD DIP Mode 52: DWN-UP-DWN-UP -- DWN-DWN-UP-DWN
MediaHub HD Firmware Version: 1.23+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Go into HOTEL MODE (using Panasonic remote, press <MENU>,
<G>, <Y>, <0>), select the following: MODE = ON, BUTTON LOCK = OFF.
Configure IMP- Tuner Card: Press <Channel Up>, <Right Arrow>, <Left
Arrow>, <MUTE> to enter set-up screen. Go to Control Options and AUX
panel. Set BAUD Rate to 9600. Go to Service Options, verify the HDMI Terminal
Card is assigned to Slot 1.
Figure 1: Panasonic with IMP- tuner card
cable connection diagram.
HDMI
5V
Adapter
RS232
DUAL HDMI IMP TUNER
Slot 1 Slot 2 Slot 3
▼
CONTROL
HDMI 1 HDMI 2
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
19
HDMI
5V
▼
HDMI 1
SERIAL
XPRESS
RS232
Philips North America
What You Will Need:
- TA-7650 or TA-7650/TA-7500L
MediaHub HD Connectivity Panel
Power Supply Cable
(Note: MediaHub with Power/Data Extender model includes
TWO power supplies – one for media panel and one for power panel)
Ethernet Cable (for MediaHub with Power/Data Extender model only)
- MediaHub Cable Kit
HDMI Cable (3m)
RS-232 Cable
- Philips Hospitality Display & Remote Control
Philips North America Direct-to-TV Installation
Follow cable connection instructions illustrated in Figure 1. Then configure the TV and
MediaHub HD according to the model-specific requirements below.
Philips HFL 2011 Models
For nnHFLL/F7, nnHFLD/F7, nnHFLF/F7, and nnHFLH/F7 models. This installation requires
Philips TV firmware version 1.13. Connect the HDMI cable to TV’s REAR HDMI1 port.
MediaHub HD DIP Mode B6: UP-DWN-UP-UP – DWN-UP-UP-DWN
MediaHub HD Firmware Version: 1.28+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Using guest remote control, enter the set-up menu by
pressing <3>, <1>, <9>, <7>, <5>, <3>, <MUTE>. Under PPV/VOD set
SerialXpress=YES.
Philips HFL 2009/2010 Models
For nnHFLD/27, nnHFLV/27 and nnHFLL/27 models
MediaHub HD DIP Mode B6: UP-DWN-UP-UP – DWN-UP-UP-DWN
MediaHub HD Firmware Version: 1.28+
MediaHub HD Video Driver Firmware: 3.26+
Configure TV: Using guest remote control, enter the set-up menu by
pressing <3>, <1>, <9>, <7>, <5>, <3>, <MUTE>. Under
Communications, set SP-SP1 to RS232 Serial port, CP=YES. Select SAVE
and Baud Rate will default to 9600.
Figure 1: Philips 2009/2010 direct-to-TV cable
connection diagram.
TA-7650 and TA-7750 Installation Manual
Last Revision: 9/30/11 11:23 AM
20
Philips HFL Models with an External PPV STB
Follow Philips Direct-to-TV installation instructions according to instructions above. Connect
the PPV STB AV Out to TV’s HDMI1 port. Connect MediaHub HD’s HDMI to TV’s HDMI2.
Philips HFL 2009 Models with an Enseo HD3000/2000
Follow instructions for Philips Direct-to-TV Installation according to the model/year of your
Philips display. OR, you may install MediaHub HD’s serial control connection to the Enseo
STB. See instructions for Enseo STB Installation.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
