Black & Decker GTC1850L User manual

www.blackanddecker.co.nz

www.blackanddecker.com.au

GTC1445L

GTC1845L

GTC1850L

C E

A B

0-15

F G

ENGLISH

(Original instructions)

Intended use

Your Black & Decker hedgetrimmer has been designed for

trimming hedges, shrubs and brambles. This tool is intended

for consumer use only.

Safety instructions

General power tool safety warnings

@Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains

operated (corded) power tool or battery operated (cordless)

power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

ENGLISH

(Original instructions)

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Battery tool use and care

manufacturer. A charger that is suitable for one type of

another battery pack.

b. designated

battery packs. Use of any other battery packs may create

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6. Service

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

@Warning! Additional safety warnings for hedge

trimmers

u Keep all parts of the body away from the cutter blade.

Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is off

when clearing jammed material. A moment of inattention

while operating the tool can result in serious personal

injury.

u Carry the hedge trimmer by the handle with the cutter

blade stopped. When transporting or storing the

Proper handling of the hedge trimmer will reduce possible

personal injury from the cutter blades.

u Hold the power tool by insulated gripping surfaces

only, because the cutter blade may contact hidden

wiring. Cutter blades contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give

the operator an electric shock.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual can present a risk of

personal injury and/or damage to property.

u Do not carry the tool with your hands on the front handle,

switch or the trigger switch unless the battery has been

removed.

u If you have not used a hedge trimmer before, preferably

seek practical instruction by an experienced user in addi-

tion to studying this manual.

u Never touch the blades while the tool is running.

u Never attempt to force the blades to come to a standstill.

u Do not put the tool down until the blades have come to a

complete standstill.

u Regularly check the blades for damage and wear. Do not

use the tool when the blades are damaged.

u Take care to avoid hard objects (e.g. metal wire, railings)

when trimming. Should you accidentally hit any such

object, immediately switch the tool off and check for any

damage.

u Should the tool start to vibrate abnormally, immediately

switch it off and remove the battery then check for any

damage.

u If the tool stalls, immediately switch it off. Remove the

battery before attempting to remove any obstructions.

u After use, place the blade sheath supplied over the

blades. Store the tool, making sure that the blade is not

exposed.

tool. Never attempt to use an incomplete tool or a tool with

u Never allow children to use the tool.

u Be aware of falling debris when cutting the higher sides of

a hedge.

u Always hold the tool with both hands and by the handles

provided.

b. Power to the tool should always be supplied via

residual current device with a rated residual current of

30mA or less.

ENGLISH (Original instructions)

Safety of others

u This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or ac-

cessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

Electrical safety

Additional safety instructions for batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between 10 °C and

40 °C.

u Charge only using the charger provided with the tool.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

pDo not attempt to charge damaged batteries.

Chargers

u Use your Black & Decker charger only to charge the bat-

tery in the tool with which it was supplied. Other batteries

could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

:Warning! To reduce the risk of injury, the user

must read the instruction manual.

OWear safety glasses or goggles when operating

this tool.

NWear ear protection when operating this tool.

RDo not expose the tool to rain or high humidity.

Directive 2000/14/EC guaranteed sound power.

Switch the tool off. Before performing any

maintenance on the tool, remove the battery

from the tool.

Keep bystanders away.

$The charger is intended for indoor use only.

+Read the instruction manual before use.

#Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Trigger switch

2. Front handle bail arm

3. Front handle

4. Lock-off button

5. Guard

6. Blade

Fig. A

7. Battery

8. Charger

9. Charge indicator

10. Battery release button

Assembly

Warning! Before assembly, remove the battery from the tool

Warning! Before assembly, make sure that the tool is

over the blades.

Warning! Never use the tool without the guard.

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (10) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (7), insert it into the charger (8).

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

(slowly).

The charge is complete when the charging indicator (9) lights

green continuously. The charger and the battery can be left

sionally tops off the battery charge. The charging indicator (9)

will be lit as long as the battery is connected to the plugged-in

charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

follows:

u Re-insert the battery (7).

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

ENGLISH

(Original instructions)

NOTE: Battery and charger not included when tool sold as

bare unit

ENGLISH (Original instructions)

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

Switching on and off

Note: For your safety, this tool is equipped with a double

switching system. This system prevents starting the tool

inadvertently and will only allow operation while holding the

tool with both hands.

u Take hold of the front handle (3) with one hand so that the

front handle bail arm (2) is pushed into the body of the

front handle.

u Pull the lock-off button (4) backwards using your thumb

and at the same time squeeze the trigger switch (1) to

start the tool.

u Release the lock-off button.

Switching off

u Release the handle switch (2) or the trigger switch (1).

Warning! Never attempt to lock a switch in the on position.

Hints for optimum use

u Start by trimming the top of the hedge. Slightly tilt the tool

(up to 15° relative to the line of cut) so that the blade tips

the blades to cut more effectively. Hold the tool at the de-

sired angle and move it steadily along the line of cut. The

double-sided blade allows you to cut in either direction.

u In order to obtain a very straight cut, stretch a piece of

string along the length of the hedge at the desired height.

Younger stems move outwards when the blade cuts

u Take care to avoid any foreign objects. Especially avoid

hard objects such as metal wire and railings, as these

u Regularly oil the blades.

Guidelines for trimming (UK & Ireland)

u Trim hedges and shrubs with seasonal leaves (new leaves

every year) in June and October.

u Trim evergreens in April and August.

u Trim conifers and other fast growing shrubs every six

weeks from May until October.

Guidelines for trimming (Australia & New Zealand)

u Trim hedges and shrubs with seasonal leaves (new leaves

every year) in December and March.

u Trim evergreens in September and February.

u Trim conifers and other fast growing shrubs every six

weeks from October until March.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the perform-

ance of your tool. By using these accessories you will get the

very best from your tool.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u After use, carefully clean the blades. After cleaning, apply

ing.

Guidelines for trimming

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Recommended fuse: 5 A.

Protecting the environment

ZSeparate collection. This product must not be

disposed of with normal household waste.

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

zSeparate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

the address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Batteries

ZAt the end of their useful life, discard batteries with

due care for our environment:

u Run the battery down completely, then remove it from the

tool.

u NiCd, NiMH and Li-Ion batteries are recyclable. Place

the battery(s) in a suitable packaging to ensure that the

terminals cannot be short-circuited. Take them to any

authorised repair agent or a local recycling station.

u Do not short-circuit the battery terminals.

in a risk of personal injury or an Explosion.

ENGLISH

(Original instructions)

Level of sound pressure according to EN 60745:

Sound pressure (LpA) 73.8 dB(A), uncertainty (K) 3.89 dB(A)

Sound power (LWA) 93.8 dB(A), uncertainty (K) 3.89 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Vibration emission value (ah, D) 2.1 m/s2, uncertainty (K) 1.5 m/s2

Technical data

GTC1445L

(H1)

GTC1850L

(H1)

GTC1845L

(H1)

Voltage VDC

VAC

14.4 18 18

Blade strokes

(no load) min-1

1200 1300 1300

Blade length

45 50 45

Blade gap

mm 18 18 18

Blade brake time s

<1 <1 <1

Weight

kg 2.4 2.6 2.6

90623445 04/2015

Australia & New Zealand

Stanley Black & Decker

www.blackanddecker.com.au

www.blackanddecker.co.nz

Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)

Black & Decker GTC1850L, GTC1845B, GTC1845L20 User manual

Related papers

Other documents