Page is loading ...
2
ENGLISH
CONTENTS
OPEN SOURCE SOFTWARE NOTICE INFORMATION .......... 3
ON CLEANING ...........................................................3
GENERAL DESCRIPTION .............................................4
NAMES AND FUNCTIONS OF COMPONENTS ...................7
ASSEMBLING BATTERY ............................................15
REMOVING BATTERY ...............................................16
HOW TO USE MAIN CABLE HOLDER ............................18
SPECIFICATION AND DIMENSION OF EACH PART .......... 19
ENVIRONMENTAL REQUIREMENT .............................. 23
INSTALLING CALIBRATION SOFTWARE .......................24
CONNECTION TYPE .................................................. 25
3
ENGLISH
OPEN SOURCE SOFTWARE NOTICE INFORMATION
To obtain the source code that is contained in this product, under GPL, LGPL, MPL, and other open source licenses
that have the obligation to disclose source code, and to access all referred license terms, copyright notices and other
relevant documents, please visit
https://opensource.lge.com
.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping, and handling) upon email request toopensource@lge.com.
This offer is valid to anyone in receipt of this information for a period of three yearsafter our last shipment of this
product.
ON CLEANING
Recommended Cleaning Chemicals
• Isopropanol 70%
• Ethanol 70%
• 0.9% NaCl solution
•
How to Use Cleaner
• Prior to cleaning, turn off the Detector and remove the power cable.
• Soak a soft cloth in a recommended cleaner, then lightly rub the screen with no more than 1N of force.
• The cleaner could cause serious damage if it leaks inside the Detector while cleaning.
• Do not use benzene, thinner, acids or alkaline cleaners or other such solvents.
• Cleaning guidelines for Detector must only be carried out by medical professionals (doctors or nurses) and must not
be handled by patients.
4
ENGLISH
GENERAL DESCRIPTION
Overview
This model is an x-ray imaging device, a system that can acquire and process X-ray images as digital images. It utilizes amorphous silicon and a high-performance scintillator to ensure sharp high-definition image quality with the resolution
of 3.6lp/mm and the pixel pitches of 140um. This device is a flat panel based X-ray image acquisition device. This device must be used in conjunction with an operating PC and an X-ray generator. This device can be used for digitizing and
transferring X-ray images for radiological diagnosis. The data transmission between the detector and PC can be enabled with a wired (cable) or wireless connection.
5
ENGLISH
Product Components
Basic Accessories
Detector Battery 2EA AC Power Cord for the AC Power Adapter Inspection Report
Owner's Manual/Regulatory Manual/Calibration Software Main Cable AC Power Adapter for Charger Battery Charger
Control Box AC Power Cord for the Control Box Main Cable Cradle
6
ENGLISH
Optional Accessories
Trigger Cable LAN Cable
• Some models may not include optional accessories.
CAUTION
• You must use the authorised components as per the specification below. Unauthorised components may cause damage and/or cause the product to malfunction.
Component Standard
LAN Cable More than CAT5E Standard
Power Cord US – Approved Medical grade regulation
Others – Approved country safety regulation
• The AC/DC adapters etc. that are being used, with the exception of the upper components, must be supplied by the manufacturer.
7
ENGLISH
NAMES AND FUNCTIONS OF COMPONENTS
Detector
Front Back
Battery
8
ENGLISH
Side
4325 1
1
Connection to Main Cable
2
• Power LED Indicator
• Power button
3
• Wired/Wireless LED Indicator
• Wired/Wireless Connection Button
4
• Function Switch LED Indicator
• Function Switch Button
5
OLED Indicator
9
ENGLISH
Button Information
Button Description
(Power button) Press the Power button to turn the power on or off.
– On: Press and hold for 1 sec or longer
– Off: Press and hold for 5 sec or longer
(Wired/Wireless Connection button) Press this button for at least one second to switch between the following connection modes, in respective order: Ethernet/Station/AP mode.
(Function Switch button) Press this button for at least one second to switch between the following menus, in respective order: Check connection mode, video acquisition, image auto save. The menu is shown
on the OLED indicator.
– Press and hold the button for at least three seconds to change the on/off settings for each function.
NOTE
• Press and hold the and buttons at the same time for at least ten seconds to restore to factory settings.
10
ENGLISH
LED Indicator
LED Description
(Power LED Indicator) Displays the power and battery status of the detector.
Off Power off
White Power on
Orange The battery level is greater than 10% and less than 30%.
Orange(blinking) The battery level is less than 10%.
(Wired/Wireless LED Indicator) Displays the connection mode status of the detector.
Green Ethernet connected
Green(blinking) Ethernet disconnected
White Wireless(Station/AP) connected
White(blinking) Wireless(Station/AP) disconnected
(LED Indicator for Function Switch) Briefly lights up in green when the Function Switch button is used to change the on/off settings.
NOTE
• If the LED indicators show the following behaviour, a system error may have occurred. Please contact the manufacturer.
- (White(blinking)) + (Green(blinking)) + (Green(blinking))
11
ENGLISH
OLED Indicator
The OLED indicator displays the information below.
Connection Mode
Information
Ethernet Station AP
Wired/STA/AP
– Check Connection Mode (Ethernet/Station/AP).
Dynamic On/Off
– Video Acquisition
Auto save On/Off (Up to 200 images)
– Image Auto save
NOTE
• The information displayed on the OLED indicator will vary depending on the connection mode (Ethernet/Station/AP).
• If left idle for ten seconds after pressing the button, the OLED indicator turns off. When the OLED indicator is turned on again, the starting screen is displayed.
12
ENGLISH
Battery and Battery Charger
LED Indicators on the Battery Charger
NOTE
• Battery: Lithium ion polymer battery (charging time - Typ. 3 hours)
• Battery Charger: 2-port cradle type
• The remaining battery level and status for each battery can be checked through the LED indicators on the battery
charger.
• If the LED indicator does not turn on when charging the battery, it may be a connection error. Please reinstall the
battery.
LED Indicators
on the Battery
Charger
Blinking Blinking Blinking
Remaining
Battery Levels 0 ~ 30% 30 ~ 70% 70 ~ 99% 100%
Battery Status On charging Completion of
charging
13
ENGLISH
Control Box
Front Back
1
7
5
2 3
6
4
Number LED Indicator LED Colour Description
1
Green Power normal operation
Off Power off (AC power cord no connection or Power error)
Green Ethernet normal operation
Green(blinking) On data communication
Off Ethernet disconnected
Green Ready signal from X-ray Generator is active
Off Ready signal from X-ray Generator is inactive
Orange(blinking) Power error
Orange Exposure signal from X-ray Generator is active
Off Exposure signal from X-ray Generator is inactive
Orange(blinking) Power error
14
ENGLISH
Number Port Description
2
Connects the Control Box to the Detector A. This connector supplies power (24V 2.1A) to the Detector and transmits the X-ray generator's sync signal and Ethernet image data.
3
Connects the Control Box to the Detector B. This connector supplies power (24V 2.1A) to the Detector and transmits the X-ray generator's sync signal and Ethernet image data.
The Control Box supports connection up to two detectors. One is for a bucky stand and the other is for a table(bed). Hospital X-ray examination rooms are typically equipped with
both bucky stand and table type detectors. This makes it more convenient and efficient to use the detectors.
4
Connects the AC power cord.
5
An Ethernet port to transmit images/commands between the Detector and a PC.
6
Synchronizes the Detector and X-ray generator.
7
Fuse Control box power fuses are 4A, 250V to Type T fuse.
Power rating: T4L 250V
15
ENGLISH
ASSEMBLING BATTERY
1 Check the direction of the holes located inside the detector. 2 Align the battery, and slide it into the holes inside the detector. 3 Press the other side to assemble the battery.
16
ENGLISH
REMOVING BATTERY
1 Slide the battery lock button in the direction shown in the figure. 2 Remove the battery by lifting it in the direction shown in the figure.
17
ENGLISH
Battery Hot-Swap
The detector is equipped with a hot-swappable battery. Hot-Swap is activated for one minute after the battery is removed from the detector.
NOTE
• The detector will turn off if charged battery is not inserted on time.
• Data collection and calibration functions are not available during a Hot-Swap.
18
ENGLISH
HOW TO USE MAIN CABLE HOLDER
1 Clean the wall before attaching the holder to it.
2 Attach the main cable holder using adhesive tape on the back.
3 Store the main cable of the detector in the holder.
NOTE
• The strength of the adhesive may be weakened depending on the environment. Avoid attaching the holder too
high on the wall.
• Ensure that the holder is firmly fixed on the wall.
• Avoid storing anything other than the main cable.
19
ENGLISH
SPECIFICATION AND DIMENSION OF EACH PART
Specifications are subject to change without notice.
The symbol ~ means alternating current, and the symbol means direct current.
Specifications
Detector
Item Specifications
Model 10HQ701G
Sensor Type a-Si TFT
Scintillator Type CsI:TI
Total Pixel Matrix 2048 x 1792pixels
Total Pixel Area 286.72mm x 250.88mm
Pixel Pitch 140um
Effective Pixel Matrix 2008 x 1752pixels
A/D Conversion 16bits
Data transmission 802.11 a/b/g/n/ac Wireless LAN Standard, 150Mbps
Wired Gigabit Ethernet Standard, 500Mbps
Cycle time Typ. 4.5Sec (Wired)
Typ. 5Sec (Wireless)
Image Transmission Typ. 1.5Sec (Wired)
Typ. 2Sec (Wireless)
Image Save Stores up to 200 images
Semi-dynamic mode 5fps @ 140um (full FOV)
Energy Range 40kVp ~ 150kVp
MTF Typ. 84% @ 0.5lp/mm
DQE Typ. 66% @ 0.1lp/mm
Item Specifications
Size (Width x Height x Depth) (mm) 333 x 282 x 15.6
Weight (kg) Typ. 1.9
Window Materials Carbon Fibre
Trigger Mode Manual Mode
Auto Mode (Auto Exposure Detection)
Power Consumption Typ.24W
Wireless Standard:
802.11 a/b/g/n/ac compliance
Peak Mode: 867Mbps
Frequency: 2.4GHz / 5GHz
Bandwidth: 20MHz / 40MHz / 80MHz
MIMO: 2 x 2
Rating 24V 2.1A
Applied part Type: BF
Location: The front side of the Detector (Effective area only)
NOTE
• Maximum wireless signal rate derived from IEEE standard specifications. Actual data throughput will vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction,
and network overhead, lower actual data throughput rate.
• Recommended Maximum operable distance: 2m (From the Access Point)
• Wireless antennas: The module adopts the latest 802.11ac technology. The transmitter of the module is powered by
host equipment (Detector). The antennas are 2 printed-dipole antennas.
• Wireless module: 802.11 a/b/g/n/ac USB2.0 module is implemented. It supports 2T2R (2 transmit 2 receive) MIMO
technology, which delivers throughput up to 300Mbps.
• Images can be saved by the X-ray generator while the power of the detector is turned on without connecting to a
PC. To produce images, X-ray is irradiated at intervals of more than 10 seconds. Check and load the saved images
from LG Acquisition Workstation Software.
20
ENGLISH
Detector has been tested with below table’s X-ray condition. This table is only for reference. The legally certified
radiologist expert should control X-ray dose.
• Sensor Type: a-Si TFT, X-ray conditions
Adult
SID (inch / cm) Tube Voltage (KV) Tube Current (mA) Tube Current x Time
(mAs)
Chest P-A 72 inch / 182.8 cm 110 KV 320 mA 3.2 mAs
C-spine LAT 72 inch / 182.8 cm 75 KV 200 mA 20 mAs
L-spine A-P 40 inch / 101.6 cm 70 KV 250 mA 25 mAs
Abdomen A-P 40 inch / 101.6 cm 75 KV 320 mA 20.48 mAs
Pelvic A-P 40 inch / 101.6 cm 70 KV 250 mA 25 mAs
Wrist A-P 40 inch / 101.6 cm 50 KV 250 mA 5 mAs
Elbow A-P 40 inch / 101.6 cm 55 KV 250 mA 5 mAs
Shoulder AP 40 inch / 101.6 cm 65 KV 200 mA 8 mAs
Foot A-P 40 inch / 101.6 cm 50 KV 250 mA 5 mAs
Ankle A-P 40 inch / 101.6 cm 55 KV 100 mA 6.4 mAs
Knee A-P 40 inch / 101.6 cm 60 KV 100 mA 8 mAs
• Sensor Type: Oxide TFT, X-ray conditions
Adult
SID (inch / cm) Tube Voltage (KV) Tube Current (mA) Tube Current x Time
(mAs)
Chest P-A 72 inch / 182.8 cm 110 KV 320 mA 2.56 mAs
C-spine LAT 72 inch / 182.8 cm 75 KV 200 mA 16 mAs
L-spine A-P 40 inch / 101.6 cm 70 KV 250 mA 20 mAs
Abdomen A-P 40 inch / 101.6 cm 75 KV 250 mA 16 mAs
Pelvic A-P 40 inch / 101.6 cm 70 KV 250 mA 20 mAs
Wrist A-P 40 inch / 101.6 cm 50 KV 200 mA 4 mAs
Elbow A-P 40 inch / 101.6 cm 55 KV 200 mA 4 mAs
Shoulder AP 40 inch / 101.6 cm 65 KV 200 mA 6.4 mAs
Foot A-P 40 inch / 101.6 cm 50 KV 200 mA 4 mAs
Ankle A-P 40 inch / 101.6 cm 55 KV 100 mA 4.8 mAs
Knee A-P 40 inch / 101.6 cm 60 KV 100 mA 6.4 mAs
NOTE
• In the case of the Oxide TFT X-ray condition table, it is only applicable to 14HQ901G-B and 17HQ901G-B models. If
the condition table is applied to other models, the desired image may not be obtained.
• Regarding paediatric dosage, it should be much less than for an adult. The certified radiologist should pay special
attention to paediatric X-ray dosage levels.
/