Robur GAHP WS Installation, Use And Maintenance Manual

Brand: Robur

Model: GAHP WS

Type: Installation, Use And Maintenance Manual

This manual is also suitable for

GAHP GS

Installation, use and maintenance manual

GAHP GS/WS

water/water gas absorption heat pump

This Installation, use and maintenance manual has been drawn up and printed by Robur S.p.A.; whole or partial

reproduction of this Installation, use and maintenance manual is prohibited.

The original is led at Robur S.p.A.

Any use of this Installation, use and maintenance manual other than for personal consultation must be previously

authorised by Robur S.p.A.

The rights of those who have legitimately led the registered trademarks contained within this publication are not

aected.

With the aim of continuously improving the quality of its products, Robur S.p.A. reserves the right to modify the

data and contents of this Installation, use and maintenance manual without prior notice.

Revision: V

Code: D-LBR509

DISPOSAL

The appliance and all its accessories must be disposed of separately in accordance with the regulations in force.

Use of the WEEE symbol (Waste Electrical and Electronic Equipment) indicates that this product cannot be disposed of as household waste.

Proper disposal of this product helps to prevent potential negative consequences for the environment and human health.

Installation, use and maintenance manual – GAHP GS/WS

INDEX OF CONTENTS

I Introduction .............................................................................

p.4

Recipients ..........................................................................

p.4

Control device ..................................................................

p.4

II Symbols and denitions ...............................................

p.4

II.1 Key to symbols .................................................................

p.4

II.2 Terms and denitions ....................................................

p.4

III Warnings......................................................................................

p.4

III.1 General and safety warnings ......................................

p.4

III.2 Conformity ........................................................................

p.6

III.3 Exclusions of liability and warranty ..........................

p.6

1 Features and technical data ......................................

p.7

1.1 Features ..............................................................................

p.7

1.2 Dimensions .......................................................................

p.8

1.3 Components ...................................................................

p.10

1.4 Electrical wiring diagram ...........................................

p.13

1.5 Electronic boards ..........................................................

p.13

1.6 Operation mode ............................................................

p.15

1.7 Controls ............................................................................

p.15

1.8 Technical characteristics .............................................

p.16

2 Transport and positioning ........................................

p.18

2.1 Warnings ..........................................................................

p.18

2.2 Handling ...........................................................................

p.18

2.3 Appliance position (outdoor version) ...................

p.18

2.4 Installation premises (indoor variant)....................

p.19

2.5 Minimum clearance distances..................................

p.19

2.6 Mounting base ...............................................................

p.19

3 Heating engineer ...............................................................

p.19

3.1 Warnings ..........................................................................

p.19

3.2 Hydraulic system ...........................................................

p.19

3.3 Hydraulic connections ................................................

p.20

3.4 Water circulation pumps ............................................

p.21

3.5 Antifreeze function .......................................................

p.21

3.6 Antifreeze liquid ............................................................

p.21

3.7 System water quality ...................................................

p.22

3.8 System lling ..................................................................

p.22

3.9 Fuel gas supply ..............................................................

p.22

3.10 Combustion products exhaust ................................

p.23

3.11 Flue gas condensate discharge ................................

p.26

3.12 Safety valve exhaust (indoor version) ....................

p.26

4 Electrical installer ..............................................................

p.27

4.1 Warnings ..........................................................................

p.27

4.2 Electrical systems ..........................................................

p.27

4.3 Electrical power supply ...............................................

p.28

4.4 Set-up and control ........................................................

p.28

4.5 Water circulation pumps ............................................

p.31

5 First start-up ..........................................................................

p.34

5.1 Preliminary checks ........................................................

p.34

5.2 Electronic adjustment on the machine – Menus

and parameters of the S61 board ...........................

p.34

5.3 Modifying settings ........................................................

p.35

6 Normal operation ..............................................................

p.36

6.1 Warnings ..........................................................................

p.36

6.2 Switch on and o ..........................................................

p.36

6.3 Modifying settings ........................................................

p.36

6.4 Eciency ..........................................................................

p.36

7 Maintenance ..........................................................................

p.36

7.1 Warnings ..........................................................................

p.36

7.2 Pre-emptive maintenance .........................................

p.37

7.3 Scheduled routine maintenance .............................

p.37

7.4 Messages on the display ............................................

p.37

7.5 Restarting a locked-down unit.................................

p.37

7.6 Periods of inactivity ......................................................

p.38

8 Diagnostics ..............................................................................

p.38

8.1 Operative codes.............................................................

p.38

9 Appendices..............................................................................

p.42

9.1 Product che...................................................................

p.42

Introduction

I INTRODUCTION

Manual

This Manual is an integral part of the GAHP GS/WS units

and must be handed to the end user together with the

appliance.

RECIPIENTS

This Manual is intended for:

▶

End user, for appropriate and safe use of the appliance.

▶

Qualied installer, for correct appliance installation.

▶

Planner, for specic information on the appliance.

CONTROL DEVICE

In order to be able to work, the GAHP GS/WS unit needs a con-

trol device (DDC, CCP/CCI or external requests), which must be

connected by the installer.

II SYMBOLS AND DEFINITIONS

II.1 KEY TO SYMBOLS

DANGER

WARNING

NOTE

PROCEDURE

REFERENCE (to other document)

II.2 TERMS AND DEFINITIONS

GAHP Appliance/Unit = equivalent terms, both used to des-

ignate the gas powered absorption heat pump GAHP (Gas

Absorption Heat Pump).

TAC = Technical Assistance Centre authorised by Robur.

External request = generic control device (e.g. thermostat,

clock or any other system) equipped with a voltage-free NO con-

tact and used as control to start/stop the GAHP unit.

CCI Controller (Comfort Controller Interface) = optional Robur

control device which lets you manage up to three modulating

heat only GAHP units (A, WS, GS).

CCP Controller (Comfort Control Panel) = Robur control de-

vice which lets you manage in modulation mode up to three

GAHP units and all system components (probes, diverter/mixing

valves, circulating pumps), including any integration boiler.

DDC Control (Direct Digital Controller) = optional Robur adjust-

ment device to control one or more Robur appliances (GAHP

heat pumps, GA chillers and AY00-120 boilers) in ON/OFF mode.

RB100/RB200 Devices (Robur Box) = optional interface devices

complementary to DDC, which may be used to broaden its func-

tions (heating/cooling/DHW production service demands, and

control of system components such as third party generators,

adjustment valves, circulators, probes).

Heat generator = equipment (e.g. boiler, heat pump, etc..) pro-

ducing heating and/or DHW.

GUE (Gas Utilization Eciency) = eciency index of gas heat

pumps, equal to the ratio between the thermal energy pro-

duced and the energy of the fuel used (relative to LCV, lower

caloric value).

First start-up = appliance commissioning operation which may

only and exclusively be carried out by a TAC.

S61/Mod10/W10 Boards = electronic boards on the GAHP unit,

to control all functions and to provide interface with other devic-

es and with the user.

III WARNINGS

III.1 GENERAL AND SAFETY WARNINGS

Installer's qualications

Installation must exclusively be performed by a qualied

rm and by qualied personnel, with specic knowledge

on heating, cooling, electrical systems and gas applianc-

es, in compliance with the laws in force in the Country of

installation.

Declaration of conformity

Upon completing installation, the installing rm shall

issue to the owner/client the appliance's workmanlike

conformity declaration, according to national/local reg-

ulations in force and the manufacturer's instructions/

provisions.

Misuse

The appliance must only be used for the purposes for

which it has been designed. Any other use is deemed

hazardous. Incorrect use may aect operation, duration

and safety of the appliance. Adhere to the manufactur-

er's instructions.

Hazardous situations

 Do not start the appliance in hazardous conditions, such

as: gas smell, problems with the plumbing/electrical/gas

system, parts of the appliance under water or damaged,

malfunctioning, disabling or bypassing control and safe-

ty devices.

 In case of danger, request intervention by qualied per-

sonnel.

 In case of danger, switch o the electrical power and gas

supplies only if this can be done in total safety.

Warnings

Installation, use and maintenance manual – GAHP GS/WS

III

 Do not entrust children, persons with physical, sensory

or mental disabilities or persons with poor knowledge

and experience with use of the appliance.

Gas component tightness

 Before performing any operation on gas ducting compo-

nents, close the gas valve.

 Upon completing any procedure, perform the tightness

test according to regulations in force.

Gas smell

If you smell gas:

 Do not use electrical devices such as telephones, mul-

timeters or other equipment that may cause sparks next

to the appliance.

 Shut o the gas supply by turning the valve o.

 Disconnect electrical power supply by means of the

external isolation switch in the power supply electrical

panel.

 Use a telephone away from the appliance to ask for inter-

vention from qualied personnel.

Poisoning

 Ensure the ue gas ducts are tightness and compliant

with the regulations in force.

 Upon completing any procedure, ensure components

are tightness.

Moving parts

The appliance contains moving parts.

 Do not remove guards during operation, and in any case

prior to disconnecting the power supply.

Burn hazard

The appliance contains very hot parts.

 Do not open the appliance and do not touch internal

components before the appliance has cooled down.

 Do not touch the ue gas exhaust before it has cooled

down.

Pressure vessels

The appliance has a sealed circuit classied as pres-

sure vessel, the tightness of which is tested by the

manufacturer.

 Do not carry out any intervention on the sealed circuit or

on the appliance's valves.

Water-ammonia solution

The GAHP/GA unit uses the ammonia-water absorption

cycle. The water-ammonia solution is contained in the

sealed circuit. The solution is harmful for health if it is in-

gested, inhaled or comes in contact with the skin.

 In the event of coolant leak keep away and disconnect

the power and gas supply (only if it is possible to do so

with no danger).

 Ask for TAC intervention.

Electrocution hazard

 Disconnect the electrical power supply before any oper-

ation on appliance components.

 For electrical connections exclusively use compliant

components and according to the specications provid-

ed by the manufacturer.

 Ensure the appliance cannot be accidentally switched

back on.

Earthing

Electrical safety depends on eective earthing system,

correctly connected to the appliance and installed ac-

cording to the regulations in force.

Distance from combustible or ammable materials

 Do not deposit ammable materials (paper, diluents,

paints, etc.) near the appliance.

Limescale and corrosion

Depending on the chemical/physical properties of the

system water, limescale or corrosion may damage the

appliance (Paragraph 3.7

p.22

 Check system sealing.

 Avoid frequent top-ups.

Chloride concentration

The concentration of chlorides or free chlorine in the

system water must not exceed the values in Table

3.2

p.22

Aggressive substances in the air

Halogenated hydrocarbons containing chlorine and u-

orine compounds cause corrosion. The air of the installa-

tion site must be free from aggressive substances.

Acid ue gas condensate

 Discharge the acid condensate of combustion ue gas,

as indicated in Paragraph 3.11

p. 26

, in compliance

with current exhaust regulations.

Switching the appliance o

Disconnecting the power supply while the appliance

is running may cause permanent damage to internal

components.

 Except in the case of danger, do not disconnect the pow-

er supply to switch o the appliance, but always and ex-

clusively act through the provided control device (DDC,

CCP/CCI or external request).

In the event of failure

Operations on internal components and repairs may

exclusively be carried out by a TAC, using only original

parts.

 In the event of failure of the appliance and/or breakage

of any component, do not attempt to repair and/or re-

store and immediately contact the TAC.

Routine maintenance

Proper maintenance assures the eciency and good op-

eration of the appliance over time.

 Maintenance must be performed according to the

Warnings

III

manufacturer's instructions (see Chapter 7

p. 36

) and

in compliance with current regulations.

 Appliance maintenance and repairs may only be entrust-

ed to rms legally authorised to work on gas appliances

and systems.

 Enter into a maintenance contract with an authorised

specialised rm for routine maintenance and for servic-

ing in case of need.

 Use only original parts.

Decommissioning and disposal

If the appliance is to be disposed of, contact the manu-

facturer for its disposal.

Keep the Manual

This Installation, use and maintenance manual must al-

ways accompany the appliance and must be handed to

the new owner or installer in the event of sale or removal.

III.2 CONFORMITY

EU Directives and standards

The absorption heat pumps of the GAHP series are certied as

conforming to standard EN 12309 and comply with the essential

requirements of the following Directives:

▶

2016/426/EU "Gas Appliances Regulation" as amended and

added.

▶

2014/30/EC "Electromagnetic Compatibility Directive" as

amended and added.

▶

2014/35/EC "Low Voltage Directive" as amended and added.

▶

2006/42/EC "Machine Directive" as amended and added.

▶

2014/68/EU "Pressure Equipment Directive" as amended

and added.

▶

811/2013/EU "Energy-Related Products regulation" as

amended and added.

▶

813/2013/EU "Ecodesign requirements regulation" as

amended and added.

Furthermore, they comply with the requirements of the follow-

ing standards:

▶

EN 677 Specic requirements for condensing boilers with

nominal heat input up to 70 kW.

▶

EN 378 Refrigerating systems and heat pumps.

Other applicable provisions and standards

The design, installation, operation and maintenance of the sys-

tems shall be carried out in compliance with current applicable

regulations, depending on the Country and location, and in ac-

cordance with the manufacturer's instructions. In particular, reg-

ulations regarding the following shall be complied with:

▶

Gas systems and equipment.

▶

Electrical systems and equipment.

▶

Heating and air conditioning systems, and heat pumps.

▶

Environmental protection and combustion products ex-

haust.

▶

Fire safety and prevention.

▶

Any other applicable law, standard and regulation.

III.3 EXCLUSIONS OF LIABILITY AND

WARRANTY

Any contractual or extra-contractual liability of the man-

ufacturer for any damage caused by incorrect installation

and/or improper use and/or failure to comply with reg-

ulations and with the manufacturer's directions/instruc-

tions shall be disclaimed.

In particular, the warranty on the appliance may be ren-

dered void by the following conditions:

 Incorrect installation.

 Misuse.

 Failure to comply with the manufacturer's indications on

installation, use and maintenance.

 Alteration or modication of the product or any part

thereof.

 Extreme operational conditions or however outside of

the operational ranges set forth by the manufacturer.

 Damages caused by external agents such as salts, chlo-

rine, sulphur or other chemical substances contained in

the installation water or present in the air of the instal-

lation site.

 Abnormal actions transmitted to the appliance by the

plant or installation (mechanical stresses, pressure, vi-

brations, thermal expansion, electrical surges...).

 Accidental damages or due to force majeure.

Features and technical data

Installation, use and maintenance manual – GAHP GS/WS

1 FEATURES AND TECHNICAL DATA

1.1 FEATURES

Operation

Based on the thermodynamic water-ammonia absorption cycle

0–NH

), the appliance simultaneously produces hot water

and chilled water, using the ground or well/ground/surface wa-

ter as a renewable energy source (cold source) and natural gas

(or LPG) as primary energy.

The thermodynamic cycle takes place within a hermetically

sealed circuit, in welded construction, perfectly tight, facto-

ry-tested, which does not require any maintenance or coolant

top-ups.

Mechanical and thermo-hydraulic components

▶

Steel sealed circuit, externally treated with epoxy paint.

▶

Sealed combustion chamber (type C).

▶

Metal mesh radiant burner, equipped with ignition elec-

trodes and ame detection, managed by an electronic ame

control box.

▶

Titanium stainless steel shell-and-tube water exchanger

(condenser), externally insulated.

▶

Titanium stainless steel shell-and-tube water exchanger

(evaporator), externally insulated.

▶

Stainless steel, shell-and-tube recovery exchanger of ue gas

latent heat.

Control and safety devices

▶

S61 electronic board with microprocessor, LCD display and

knob.

▶

Mod10 additional electronic board (integrated in S61).

▶

Auxiliary W10 electronic board.

▶

Installation water ow meter (hot side).

▶

Installation water ow switch (cold side).

▶

Generator limit thermostat, with manual reset.

▶

Flue gas thermostat, with manual reset.

▶

Generator ns temperature probe.

▶

Sealed circuit safety relief valve.

▶

Bypass valve, between high and low-pressure circuits.

▶

Ionization ame control box.

▶

Double shutter electric gas valve.

▶

Antifreeze functions for hydraulic circuit.

▶

Condensate discharge sensor.

Outdoor and indoor versions

The GAHP GS/WS units are available in two versions, indoor or

outdoor, according to the installation site.

Features and technical data

1.2 DIMENSIONS

Figure1.1 Indoor GAHP GS/WS dimensions

A Flue gas output Ø 80

B Combustion air inlet Ø 80

C Fumes thermostat manual reset

D Power supply cables input

E Ventilation fan

F Burner on warning light

G Gas connection Ø 3/4"

H Hot water inlet Ø 1"¼

L Renewable source water return Ø 1"¼

M Renewable source water delivery Ø 1"¼

N Hot water delivery Ø 1"¼

Q Safety valve outlet ducting Ø 1"¼

Features and technical data

Installation, use and maintenance manual – GAHP GS/WS

Figure1.2 Outdoor GAHP GS/WS dimensional drawing

A Flue gas output Ø 80

B Combustion air inlet Ø 80

C Fumes thermostat manual reset

D Power supply cables input

E Ventilation fan

F Appliance operation warning light

G Gas connection Ø 3/4"

H Hot water inlet Ø 1"¼

L Renewable source water return Ø 1"¼

M Renewable source water delivery Ø 1"¼

N Hot water delivery Ø 1"¼

P Condensate drain

Features and technical data

1.3 COMPONENTS

Figure1.3 Internal components - front view

1 Ventilation fan

2 Gas valve

3 Combustion blower

4 Tmix air-gas mixture temperature probe

5 Electrical panel

6 Oil pump

7 Flow meter (hot side)

















Features and technical data

Installation, use and maintenance manual – GAHP GS/WS

Figure1.4 Internal components - left side view

1 Manual air vent (cold side)

2 Flow switch (cold side)

3 Manual reset of the ue exhaust thermostat

4 Ø 80 ue gas exhaust

5 Sensing element of the ue exhaust thermostat

6 Generator ns temperature probe

7 Condensate drain sensor

8 Flame sensor / ignition electrodes

9 Condensate drain siphon

10 Manual air vent valve (hot side)

Features and technical data

Figure1.5 Internal components - right side view

1 Safety valve

2 TG generator temperature probe

3 Limit thermostat

4 Ignition transformer

5 Flow temperature probe (hot side)













Features and technical data

Installation, use and maintenance manual – GAHP GS/WS

1.4 ELECTRICAL WIRING DIAGRAM

Figure1.6 Appliance wiring diagram

SCH1 Controller S61

SCH2 W10 circuit board

SCH3 Mod10 circuit board

TER Power supply terminal block

CNTBOX Flame controller

PWRTR Board transformer

BLW Blower

PMP Oil pump

IGNTR Ignition transformer

IGN Ignition electrodes

FLS Flame sensor

LS Gas valve ON indicator lamp

GV Gas solenoid valve

THMF Cold water delivery temperature sensor

THRF Cold water return temperature sensor

TMIX Combustion air temperature sensor

TA Ambient air temperature sensor

TG Generator temperature sensor

THMC Hot water ow temperature probe

THRC Hot water return temperature probe

REED Oil pump rotation sensor

TF Fumes temperature sensor or generator n

sensor

TC Manual ue gas thermostat

TL Generator limit thermostat

FM Hot side owmeter

FL Renewable source water ow switch

CWS Condensate water sensor

MA Terminal block

1.5 ELECTRONIC BOARDS

Electronic boards (S61+Mod10)

The unit's electrical board contains:

▶

Electronic board S61 (Figure 1.7

p. 14

), with

microprocessor, it controls the appliance and displays data,

messages and operative codes. The appliance is monitored

and programmed by interacting with the display and the

knob.

▶

Auxiliary Mod10 Electronic Board (Figure 1.8

p. 15

overlapping S61, controls power modulation of the burner

Features and technical data

and water circulation pump rate variation.

▶

Satellite W10 electronic board (Figure 1.9

p. 15

interconnected to the S61 board and located next to it, used

mainly to control hot side circulating pump.

Figure1.7 Electronic board S61

SCH1 Controller S61

SCH3 Mod10 electronic board (see specic gure

for further details)

A1, A2 Auxiliary inputs

ENC Knob

F1 T 2A fuse

F2 T 10A fuse

F3 T 2A fuse

F4 T 3,15A fuse

FAN (BK, WH, BR) Cooling fan output

FL Flow switch input

FS5 (24V AC) board supply 24-0-24 Vac

IGN.BOX (L, N) Flame controller power supply

230 Vac

J1 CAN bus Jumper

J10 Jumper N.O. contact

J82 W10 board connector (on Mod10)

JP10 6-pole ame controller connector

JP12 Flue gas probe or generator n probe input

JTAG S61 board programming connector

MAIN 230V (L, N) S61 board supply input 230 Vac

N.O. CONTACT Normally open pump contact

P7 (R, W, Y, O) Enable input

P8 (GND, L, H) CAN bus connector

PUMP 230V (L, N) Oil pump supply output

SPI Communication port with Mod10

controller

SRT1 Oil pump rotation sensor input

SRT2 Hot water owmeter input

TA Ambient air temperature probe input

TA1 Hot water ow temperature probe input

TA2 Hot water inlet temperature probe input

TCN Combustion air temperature probe input

TF Flue gas thermostat input

TG Generator temperature probe input

THMF Cold water inlet temperature probe input

THRF Cold water inlet temperature probe input

TL Generator limit thermostat input

Features and technical data

Installation, use and maintenance manual – GAHP GS/WS

Figure1.8 Mod10 controller

HFLOW Not used

CFLOW Condensation water sensor control

J51 S61 connector

HPMP Primary circuit hot water pump control

output (0-10 V) [A/GS/WS]

CPMP Cold side water pump control output

[GS/WS]

NC1-C1 Status indication of locking warnig/error

CN5 Blower control

J82 W10 auxiliary controller connector

J83 W10 cable shielding connection

CN1 Inputs 0-10V (not used)

1235 4

Figure1.9 W10 electronic controller

JP1 Communication with S61/Mod10

1.6 OPERATION MODE

ON/OFF or modulating operation

The GAHP unit may work in two modes:

▶

Mode (1) ON/OFF, i.e. on (at full power) or o, with circulat-

ing pumps at constant ow.

▶

Mode (2) MODULATING, i.e. at variable load from 50% to

100% of power, with circulating pumps at variable ow (hot

side) and constant ow (cold side).

For each mode, (1) or (2), specic control systems and devices

are provided (Paragraph 1.7

p.15

1.7 CONTROLS

Control device

The appliance may only work if it is connected to a control de-

vice, selected from:

▶

(1) DDC control

▶

(2) CCP/CCI control

▶

(3) external request

1.7.1 Control system (1) with DDC (GAHP unit ON/

OFF)

The DDC controller is able to control appliances, a single GAHP

unit, or even several Robur GAHP/GA/AY units in cascade, only

in ON/OFF mode (non modulating). For more details refer to the

DDC, RB100, RB200 Manuals and the Design Manual.

DDC Controller

The main functions are:

▶

Setup and control of one (or more) Robur units of the

Features and technical data

absorption line (GAHP, GA, AY).

▶

Data display and parameters setting.

▶

Hourly programming.

▶

Climatic curve control.

▶

Diagnostics.

▶

Errors reset.

▶

Possibility to interface with a BMS.

DDC functionality may be extended with auxiliary Robur devices

RB100 and RB200 (e.g. service requests, DHW production, Third

Party generator control, probe control, system valves or circulat-

ing pumps, ...).

1.7.2 Control system (2) with CCP/CCI (modulating

GAHP unit)

The CCP/CCI control is able to control in heating only (and pos-

sibly passive cooling) up to 3 GAHP units in modulating mode

(therefore A/WS/GS only, excluding AR/ACF/AY), plus any inte-

gration ON/OFF boiler. For additional details and diagrams refer

to the CCP/CCI Manual and the Planning Manual.

CCP/CCI Control

See CCP/CCI device Manual.

1.7.3 Adjustment system (3) with external request

(GAHP unit ON/OFF)

The appliance may also be controlled via generic request de-

vices (e.g. thermostat, timer, button, contactor...) tted with

voltage-free NO contact. This system only provides elementary

control (on/o, with xed setpoint temperature), hence without

the important functions of systems (1) and (2). It is advisable to

possibly limit its use to simple applications only and with a sin-

gle appliance.There are two control options: heating request or

cooling request.

For connection of the selected device to the appliance's

electronic board please refer to Paragraph 4.4

p.28

1.8 TECHNICAL CHARACTERISTICS

Table1.1 GAHP GS/WS technical data

GAHP GS HT GAHP WS

Heating mode

Seasonal space heating energy eciency class

(ErP)

medium-temperature application (55 °C) - A++

low-temperature application (35 °C) - A+

Heat output

Evaporator inlet temperature/Delivery

temperature

B0W35 kW 41,6 -

B0W50 kW 37,6 -

B0W65 kW 31,4 -

W10W35 kW - 43,9

W10W50 kW - 41,6

W10W65 kW - 35,8

GUE eciency

Evaporator inlet temperature/Delivery

temperature

B0W35 % 165 -

B0W50 % 149 -

B0W65 % 125 -

W10W35 % - 174

W10W50 % - 165

W10W65 % - 142

Heat input

nominal (1013 mbar - 15 °C) (1) kW 25,7

real kW 25,2

Hot water delivery temperature

maximum for heating °C 65

maximum for DHW °C 70

Hot water return temperature

maximum for heating °C 55

maximum for DHW °C 60

minimum temperature in continuous operation °C 30 (2)

Thermal dierential nominal °C 10

Heating water ow

nominal l/h 3170 3570

maximum l/h 4000

minimum l/h 1400

Pressure drop heating mode

for nominal water ow (B0W50) bar 0,49 (3) -

for nominal water ow rate(W10W50) bar - 0,57 (3)

Ambient air temperature (dry bulb)

maximum °C 45

minimum °C 0 (4)

Renewable source operating conditions

(1) Relative to NCV (net caloric value).

(2) In transient operation, lower temperatures are allowed.

(3) For ows other than nominal see Design Manual, Pressure losses Paragraph.

(4) Data referred to the indoor version. For the outdoor version, the minimum ambient air temperature is -15 °C. A special outdoor version is available as an option for operation down to -30 °C.

(5) ±10% depending on power voltage and absorption tolerance of electric motors.

(6) PCI (G20) 34,02 MJ/m³ (15 °C - 1013 mbar).

(7) PCI (G30/G31) 46,34 MJ/kg (15 °C - 1013 mbar).

(8) Sound power values detected in compliance with the intensity measurement methodology set forth by standard EN ISO 9614; C type installation.

(9) Maximum sound pressure levels in free eld, with directionality factor 2, obtained from the sound power level in compliance with standard EN ISO 9614; C type installation.

(10) Indoor variant only.

(11) Overall dimensions excluding fumes pipes.

Features and technical data

Installation, use and maintenance manual – GAHP GS/WS

GAHP GS HT GAHP WS

Power recovered from renewable source

Evaporator inlet temperature/Delivery

temperature

B0W35 kW 16,4 -

B0W50 kW 12,1 -

B0W65 kW 7,0 -

W10W35 kW - 18,7

W10W50 kW - 16,6

W10W65 kW - 10,6

Renewable source water return temperature maximum °C 45

Renewable source delivery water temperature minimum °C -5 3

Renewable source water ow rate (with 25%

glycol)

nominal (B0W50) l/h 3020 -

maximum l/h 4000 -

minimum l/h 2000 -

Renewable source water ow rate

nominal (W10W50) l/h - 2850

maximum l/h - 4700

minimum l/h - 2300

Renewable source pressure drop at nominal water ow bar 0,51 (3) 0,38 (3)

Electrical specications

Power supply

voltage V 230

type - SINGLE PHASE

frequency Hz 50

Electrical power absorption nominal kW 0,41 (5)

Degree of protection IP - X5D

Installation data

Gas consumption

G20 natural gas (nominal) m³/h 2,72 (6)

G20 natural gas (min) m³/h 1,34

G25 (nominal) m³/h 3,16

G25 (min) m³/h 1,57

G30 (nominal) kg/h 2,03 (7)

G30 (min) kg/h 0,99

G31 (nominal) kg/h 2,00 (7)

G31 (min) kg/h 0,98

emission class - 5

emission ppm 25,0

CO emission ppm 36,0

sound power L

(max) dB(A) 66,1 (8)

sound pressure L

at 5 metres (max) dB(A) 44,1 (9)

minimum storage temperature °C -30

maximum water pressure in operation bar 4,0

maximum ow ue condensate l/h 4,0

Water content inside the apparatus

hot side l 4

cold side l 3

Water tting

type - F

thread “ 1 1/4

Gas connection

type - F

thread “ 3/4

safety valve outlet channel tting “ 1 1/4 (10)

Flue gas exhaust

diameter (Ø) mm 80

residual head Pa 80

product conguration C63

type of installation - C13, C33, C43, C53, C63, C83, B23P, B33

Dimensions

width mm 848 (11)

depth mm 690

height mm 1278

Weight in operation kg 300

General information

Cooling uid

ammonia R717 kg 7,0 7,2

water H

O kg 10,0 9,6

maximum pressure of the cooling circuit bar 32

(1) Relative to NCV (net caloric value).

(2) In transient operation, lower temperatures are allowed.

(3) For ows other than nominal see Design Manual, Pressure losses Paragraph.

(4) Data referred to the indoor version. For the outdoor version, the minimum ambient air temperature is -15 °C. A special outdoor version is available as an option for operation down to -30 °C.

(5) ±10% depending on power voltage and absorption tolerance of electric motors.

(6) PCI (G20) 34,02 MJ/m³ (15 °C - 1013 mbar).

(7) PCI (G30/G31) 46,34 MJ/kg (15 °C - 1013 mbar).

(8) Sound power values detected in compliance with the intensity measurement methodology set forth by standard EN ISO 9614; C type installation.

(9) Maximum sound pressure levels in free eld, with directionality factor 2, obtained from the sound power level in compliance with standard EN ISO 9614; C type installation.

(10) Indoor variant only.

(11) Overall dimensions excluding fumes pipes.

Transport and positioning

Table1.2 PED data

GAHP GS HT GAHP WS

PED data

Components under pression

generator l 18,6

leveling chamber l 11,5

evaporator l 3,7

cooling volume transformer l 4,5

absorber/condenser l 3,7

cooling absorber solution l 6,3

solution pump l 3,3

test pressure (in air) bar g 55

maximum pressure of the cooling circuit bar g 32

lling ratio kg of NH

/l 0,146 0,150

uid group - group 1°

2 TRANSPORT AND POSITIONING

2.1 WARNINGS

Damage from transport or installation

The manufacturer shall not be liable for any damage dur-

ing appliance transport and installation.

On-site inspection

 Upon arrival at the site, ensure there is no transport dam-

age on packing or metal panels.

 After removing the packing materials, ensure the appli-

ance is intact and complete.

Packing

 Only remove the packing after placing the appliance on

site.

 Do not leave parts of the packing within the reach of

children (plastic, polystyrene, nails...) since they are po-

tentially dangerous.

Weight

 The crane and lifting equipment must be suitable for the

load.

 Do not stand under suspended loads.

2.2 HANDLING

Handling and lifting

▶

Always handle the appliance in its packing, as delivered by

the factory.

▶

To lift the appliance use straps or slings inserted in the holes

of the base (Figure 2.1

p.18

▶

Use lifting beams to avoid damaging the outer panels and

nned coil (Figure 2.1

p.18

▶

Comply with safety regulations at the installation site.

Figure2.1 Instruction for lifting

In the event of handling with forklift or pallet truck,

comply with the handling instructions shown on the

packing.

2.3 APPLIANCE POSITION OUTDOOR

VERSION

Do not install the outdoor version inside a room, not

even if it has openings. In no event the outdoor version

may be started inside a room.

Where to install the appliance

In the outdoor version the appliance:

▶

May be only installed outside buildings, out of the dripping

line of rain gutters or the like. It does not require protection

from weathering.

▶

The appliance may be installed at ground level, on a terrace

or on a roof, compatibly with its dimensions and weight.

▶

The appliance's ue gas exhaust must not be immediately

close to openings or air intakes of buildings, and must com-

ply with environmental regulations.

▶

Do not install near the exhaust of ues, chimneys or hot

polluted air. In order to work correctly, the appliance needs

clean air.

Heating engineer

Installation, use and maintenance manual – GAHP GS/WS

Acoustic issues

▶

Pre-emptively assess the appliance's sound eect in connec-

tion to the site, taking into account that building corners, en-

closed courtyards, restricted spaces may amplify the acous-

tic impact due to the reverberation phenomenon.

2.4 INSTALLATION PREMISES INDOOR

VARIANT

The installation premises must meet all the requirements set

forth by laws, standards and regulations of the Country and place

of installation regarding gas appliances and cooling appliances

Do not install inside a room that has no aeration open-

ings.

Features of the installation premises

▶

The premises must be provided with permanent and su-

ciently wide ventilation openings to permit even air ow for

aeration and possibly for combustion (if type B installation).

▶

Combustion air intake may be ducted from the outside (type

C installation).

▶

The ue gas exhaust must be ducted to the outside. The ue

opening must not be immediately close to openings or air

intakes of buildings, and must comply with environmental

regulations.

2.5 MINIMUM CLEARANCE DISTANCES

For both the indoor and outdoor version:

Distances from combustible or ammable materials

▶

Keep the appliance away from combustible or ammable

materials or components, in compliance with applicable

regulations.

Clearances around the appliance

The minimum clearance distances shown in Figure 2.2

p. 19

(bar any stricter regulations) are required for safety, operation

and maintenance.

Figure2.2 Clearances

2.6 MOUNTING BASE

Base or oor construction features

▶

Place the appliance on a levelled at surface made of re-

proof material and able to withstand its weight.

For the outdoor version:

(1) - installation at ground level

▶

Failing a horizontal supporting base, make a at and levelled

concrete base, at least 100-150 mm larger than the appli-

ance size per side.

(2) - installation on terrace or roof

▶

The structure of the building must support the total weight

of the appliance and the supporting base.

▶

If necessary, provide a maintenance walkway around the ap-

pliance.

Anti vibration mountings

Although the appliance's vibrations are minimal, resonance

phenomena might occur in roof or terrace installations.

▶

Use anti-vibration mountings.

▶

Also provide anti-vibration joints between the appliance

and water and gas pipes.

3 HEATING ENGINEER

3.1 WARNINGS

General warnings

Read the warnings in Chapter III

p. 4

, providing im-

portant information on regulations and on safety.

Compliance with installation standards

Installation must comply with applicable regulations in

force, based on the installation Country and site, in mat-

ters of safety, design, implementation and maintenance

of:

 heating systems

 cooling systems

 gas systems

 ue gas exhaust

 ue gas condensate discharge

Installation must also comply with the manufacturer's

provisions.

3.2 HYDRAULIC SYSTEM

Primary and secondary circuit

▶

In many cases it is advisable to divide the water installation

(hot side) into two parts, primary and secondary circuit, un-

coupled by a hydraulic separator, or possibly by a tank that

also acts as inertial volume/thermal inertia.

Heating engineer

Constant ot variable water ow

The GAHP unit is able to operate with constant water ow rate

(always on the cold side) or variable (on hot side only), according

to ON/OFF or modulating operative mode.

System and components must be designed and installed

consistently.

Minimum water content

High thermal inertia is conducive to ecient appliance opera-

tion. Very short ON/OFF cycles are to be avoided.

▶

If necessary, provide for an inertial volume (on hot side), to

be suitably sized (see planning manual).

Heating and/or cooling

It may be required to alternatively or simultaneously produce

hot water and/or chilled water. The selection of the type of op-

eration may be performed by the control device, by suitably se-

lecting the priority (cooling or heating).

3.3 HYDRAULIC CONNECTIONS

Plumbing ttings

on the rear panel (Figures 1.1

p.8

and 1.2

p.9

▶

N (= out) 1"1/4 F -WATER OUTPUT (hot) (m = ow to the in-

stallation);

▶

H (= in) 1"1/4 F- WATER INPUT (hot) (r = inlet from the in-

stallation).

▶

M (= out) 1"1/4 F - WATER OUTPUT (cold) (m = ow to the

installation);

▶

L (= in) 1"1/4 F - WATER INPUT (cold) (r = inlet from the

installation).

Hydraulic pipes, materials and features

▶

Use pipes for heating/cooling installations, protected from

weathering, insulated for thermal losses, with vapour barrier

to prevent condensation.

Pipe cleaning

 Before connecting the appliance,accurately wash the

water and gas piping and any other system component,

removing any residue.

Minimum components of primary water circuits

Always provide, near the appliance, both on the hot side and

cold side:

▶

on water piping, both output and input (m/r)

 2 antivibration joints on water ttings

 2 pressure gauges

 2 isolation ball valves

▶

on the input water piping (r)

 1 separator lter

 1 ow regulation valve, if the circulation pump is with

constant ow

 1 water circulation pump, towards the appliance

▶

on the output water piping (m) (hot side only)

 1 safety valve (3 bar)

 1 expansion tank of the individual unit

For GAHP GS/WS with open circuit the EXCHANGER is

obligatory.

Figure3.1 GAHP GS Water diagram

The ow regulator valve must only be used when the

primary circuit circulation pump is constant

ow type

A Gas connection

1 Anti-vibration connection

2 Pressure gauge

3 Flow regulator valve

4 Water lter

5 Shut-o valves

6 Hot side circulation pump (primary circuit)

7 Cold side circulation pump (primary circuit)

8 Safety valve (3 bar)

9 Expansion tank

10 Hydraulic separator/4-pipe buer tank

11 Hot side circulation pump (secondary circuit)

12 Geothermal eld probes

Page is loading ...

Robur GAHP WS Installation, Use And Maintenance Manual

Brand: Robur

Model: GAHP WS

Type: Installation, Use And Maintenance Manual

This manual is also suitable for

GAHP GS

Download PDF

report

Robur GAHP WS Installation, Use And Maintenance Manual

This manual is also suitable for

Robur GAHP WS Installation, Use And Maintenance Manual

Related papers

Other documents