Kreg Multi-Purpose Shop Stand User manual

Brand
Kreg
Model
Multi-Purpose Shop Stand
Type
User manual

Kreg Multi-Purpose Shop Stand: Your Sturdy and Versatile Workstation

With a load capacity of up to 400 lbs., the Kreg Multi-Purpose Shop Stand is a robust and reliable addition to any workshop. Its durable construction, consisting of sturdy legs, side rails, and end rails, ensures stability and longevity. The stand's adjustable height and leveling feet allow for precise positioning and a level work surface, accommodating a variety of tasks and project requirements.

Kreg Multi-Purpose Shop Stand: Your Sturdy and Versatile Workstation

With a load capacity of up to 400 lbs., the Kreg Multi-Purpose Shop Stand is a robust and reliable addition to any workshop. Its durable construction, consisting of sturdy legs, side rails, and end rails, ensures stability and longevity. The stand's adjustable height and leveling feet allow for precise positioning and a level work surface, accommodating a variety of tasks and project requirements.

Page is loading ...
1
Lay two legs (1) and two side rails (2) inside faces up on your work
surface in the conguration shown. Note the location of the logo
sticker. Insert carriage bolts (3) and nger-tighten the nuts (4).
Construct two side assemblies
Assembly
2
Square the rails to the legs, and then tighten the nuts. Repeat these
two steps with a second side assembly.
3
OPTION: A second set of holes allows you to lower the upper rails
4¼" to accommodate drawers or a bench vise. When using this
option, make sure your bench top will span the distance between the
legs without sagging. When mounting the Kreg Precision Router Table
Top PRS1025 on this stand, install the rails in the upper position.
90
°
4
3
1
1
2
2
4
1
⁄4"
1
Lay one side assembly inside face up on your work surface.
Position the end rails (5), insert carriage bolts (3), and nger-tighten
the nuts (4). Square the end rails to the legs, and then tighten the nuts.
Add the end rails
2
Position the second side assembly on the upright ends of the end
rails. Insert carriage bolts and tighten the nuts, again making sure
the rails are square to the legs.
1
Place the legs/rails assembly upside down on your work surface.
Position a foot (6) inside each upended leg. Fasten each foot with
four carriage bolts (3) and four nuts (4).
Install the feet and the levelers
Assembly
5
3
6
6
2
Thread a nut (7) onto each leveler (8) until it is approximately ¼"
from the leveler pad. Insert the levelers into the feet. Thread a
second nut onto each leveler and nger-tighten it.
Assembly
Mobilize your stand
Add mobility to your bench with Kreg Heavy-Duty Casters (Item
#PRS3090). These casters feature a dual-locking mechanism
that keeps the caster from rolling and pivoting, resulting in an
extremely stable work station.
1
Place your bench top (not included) face-down on your work
surface. Center the upside-down stand on it. Using a 6"-long #2
square-drive bit, drive the
3
⁄4" wood screws (9) through the holes in the
top anges and into the bench top. Turn the bench upright.
Join the Stand to Your Bench Top
2
OPTION: The Kreg Precision Router Table Top PRS1025 has
pilot holes that match the hole locations in the stand rails. When
mounting this table top, align the rail holes with the pilot holes and drive
the screws.
1
To adjust the levelers, back off the top ange nut, hold the hex
shank on the leveler stud with one wrench and turn the bottom
ange nut up or down as needed with a second wrench. With all levelers
adjusted, tighten the top ange nuts.
Level the Bench
8
7
!
ATTENTION Make sure the thickness of your bench top
accommodates the ¾"-long screws.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Kreg Multi-Purpose Shop Stand User manual

Brand
Kreg
Model
Multi-Purpose Shop Stand
Type
User manual

Kreg Multi-Purpose Shop Stand: Your Sturdy and Versatile Workstation

With a load capacity of up to 400 lbs., the Kreg Multi-Purpose Shop Stand is a robust and reliable addition to any workshop. Its durable construction, consisting of sturdy legs, side rails, and end rails, ensures stability and longevity. The stand's adjustable height and leveling feet allow for precise positioning and a level work surface, accommodating a variety of tasks and project requirements.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents