Wynn Environmental 35A Series Assembly Instructions

Brand: Wynn Environmental

Model: 35A Series

Type: Assembly Instructions

35A Series Instructions, Revision G, January 8, 2018

211 Camars Drive, Warwick, PA 18974

(215) 442-9443, fax (215) 442-9445

www.WynnEnv.com

Filter Kit Instructions

35A Series Assembly Instructions

35A Series to Harbor Freight and similar collectors

(Rim diameter more than 18” :

• Underside of filter and hole in orifice pan shown in

photo.

• Filter Gasket seats against the surface of the orifice

pans, check the surface for flaws.

• Latches get placed in a triangular pattern on the

underside of the filter (shown at top of photo)

• Collector orifice pan rim show at bottom of photo

• Do not over tighten the latches

35A Series to “Older

”

Delta 50

760 Collectors

(Rim diameter

less than 18” :

• The filter rests on top of the collector rim so a gasket is

needed. Our ETG-55 edge trim gasket is recommended.

• There is no orifice pan but these collectors have an internal

ring to which the latches get anchored from underneath.

(see Photo left)

• Customer must bend a ½” offset at the bottom of each latch

(see photo right)

• Do not over tighten the latches

Included

with

each 35A Series Filter

(1) Filter #35A100SBOL, #35A274BLOL or 35A274NANO

(3) FGL-U (Floating Gear Latches. (2) Poly Bag #1940PB

When installing or adjusting these latches please hold the body of the latch firmly

with pliers.

cluded with ETG

55 (Edge Trim Gasket):

(3) Latch Keepers, (6) Spring Nuts (uni-directional)

(6) Screws

Only used on collectors with an upper rim diameter of less

than 17 inches.

35A Series Instructions, Revision G, January 8, 2018

35BA222NANO

Assembly Instructions

35A Series to a “Newer” Delta 50

760 and similar collectors

(Rim diameter

less than 18”:

• The filter rests on top of the collector rim so a gasket is needed. Our ETG-

55 edge trim gasket is recommended. There is no orifice pan or inner ring to

anchor the latches to so the enclosed latch keepers are needed.

• About 2 – ½” from the top, spaced evenly, mark the location where the latch

keepers will go, then with a 3/16” drill bit, drill the mounting holes. Clip the

spring nuts over the holes of each keeper and with the provided screws;

secure the keepers on the inside. (see photo left)

•

o not over tighten the latches.

First:

Before placing the provided (loose) top end cap onto the filter, install the filter onto your collector.

Installation varies with the configuration of the collector.

Next: (Important)

If you will be Incorporation a DIY “Filter Monitor” (Found under Woodworking Filters on our site), now is

a good time to do it while the end cap is loose.

Top End cap Preparation:

• Cut the provided thin rubber protective trim into four (4) 12” lengths.

• With about 1–1/2” inches between them, press each segment onto the rim leaving room for the

“provided” (small) floating gear latches.

• With the Trim facing upward and gasket facing downward, place the end cap onto the fixed (open)

filter end cap. Allign it.

• Pre-adjust each of the small provided Floating Gear Latches to about 1-1/4 inches (prong ID to

prong ID.

• Secure it with all the latches as shown. When installing or adjusting the latches, please hold the

body of the latch firmly with pliers. Do not over tighten.

Shown With top end cap

secured

Shown Partially Assembled

Open end is shown

Wynn Environmental 35A Series Assembly Instructions

Brand: Wynn Environmental

Model: 35A Series

Type: Assembly Instructions

Download PDF

report

Wynn Environmental 35A Series Assembly Instructions

Wynn Environmental 35A Series Assembly Instructions

Other documents