Pazzaz 20IN PAZAAZ PETAL HERITAGE BIKE User manual

Brand
Pazzaz
Model
20IN PAZAAZ PETAL HERITAGE BIKE
Type
User manual

This manual is also suitable for

QUICK ASSEMBLY GUIDE
Pz
WARNINGS
BOX CONTENTS
FITTING THE HANDLEBAR
FITTING THE SADDLE
CONTENTS
WARNINGS
IF YOU NEED ASSISTANCE WITH ASSEMBLY PLEASE CALL
OUR CUSTOMER HELPLINE ON 03300 904 404
....................................................page 2
.............................................page 3
.............................page 4
....................................page 5
FITING THE FRONT WHEEL
FITTING THE PEDALS
FITTING THE REFLECTORS & BELL
FINAL CHECKS
...........................page 6
.....................................page 8
.................page 9
.............................................page 10
Always check that brakes work before each use - failure to set brakes correctly may result in serious injury or even death.
Ensure all nuts / bolts / screws are securely ghtened and checked before use. Recommended torques (ghtness levels) are
available in the owners manual.
Check bike regularly for signs of damage. Do not use again unl repaired.
Keep your bike in good condion by cleaning off dirt, keeping it well maintained and storing in a dry place.
Always wear a helmet that meets the latest safety standards and make sure you follow the manufaterer’s instrucons.
2
BOX CONTENTS
3
Please check contents of box carefully. If there are any parts missing please contact 03300 904 404 in the first instance
where they will be able to assist you with replacements.
Below is a list of parts you should have.
L
R
Frame Assembly Front Wheel
Rear Reflector (Red)
Front Reflector (White)
Bar Assembly
(aached to frame assembly
via brake cable)
Pedals x 2
(make sure you have an
‘L’ and an ‘R’ as shown)
Spanner Allen KeySaddle Assembly
Instrucon Manual
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
Bell
4
1.- FITTING THE HANDLEBAR
A
Insert the handlebar into the frame. If
necessary loosen the stem bolt at the top of
the handlebars and stem to allow the wedge
nut to move freely. Make sure the minimum
inseron mark is not visible once this is fied.
The handlebar must be inserted beyond this
point.
B
The handlebar must be straight. Align this with the fork by
looking downwards at it. The brakes must be facing the front
of the bike. Use the allen key to ghten the bolt on top of the
handlebar stem. Do not fully ghten unl the end as you may
need to adjust the height.
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
TOOLS NEEDED
ALLEN KEY
ALLEN BOLT
Front of bike
Front of bike
Rear of bike
Rear of bike
BRAKES
FORK
TOP VIEW
BIKE FRAME
MINIMUM
INSERTION
MARK
HANDLEBAR
5
MINIMUM
INSERTION
MARK
2.- FITTING THE SADDLE
A B
Using the spanner provided, lock the seat in posion
by turning bolt in a clockwise direcon. Do not fully
ghten unl the end as you may need to adjust the
height.
Insert saddle into frame. Make sure the minumum
insertion mark is not visible once this is tted. The
saddle must be inserted beyond this point
SADDLE
FRAME
TOOLS NEEDED
SPANNER
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
6
A
You will need to release your caliper brakes to
install or replace a wheel, slightly loosen the cable
pinch bolt. Turn it an-clockwise with the spanner
provided as shown. This will open up the break
pads so the wheel fits through.
3.- FITTING THE FRONT WHEEL
B
Turn the bike upside down. Loosen the nuts on the
front wheel axle by turning an-clockwise - you
need enough thread showing on the axle so the
wheel slots easily onto the fork. Make sure the
locking washers are on the outside of the fork as
shown.
TOOLS NEEDED
SPANNER
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
LOCKING
WASHER
NUTS
AXLE
FORK
i
ii
7
Once the wheel is in place and ght, turn the bike the right way up
and squeeze the brake arms together unl there is a 1 - 1.5 mm
gap betwen the brake pads and the rim. Both sides should be
equal. Whilst holding in place you then need to pull the brake
cable ght, and ghten the cable pinch bolt by turning clockwise
using the spanner provided as shown.
Place the pointed side of the locking washer into the
hole on the fork. Make sure the gap between the
wheel and the fork is equal on both sides.
Tighten the nut with the spanner provided.
THE PIN ON THE LOCKING
WASHER MUST BE PLACED
IN THE HOLE.
D
C
Locking washers must be posioned correctly in this step:
CORRECT BRAKE & WHEEL FITTING IS VERY IMPORTANT FOR YOUR SAFETY
IF YOU HAVE ANY PROBLEMS THERE IS MORE INFORMATION IN THE USER MANUAL
FAILURE TO CORRECTLY SET THE BRAKES MAY RESULT IN SERIOUS INJURY
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
i
ii
8
4.- FITTING THE PEDALS
TOOLS NEEDED
SPANNER
SCREW CLOCKWISESCREW ANTI-CLOCKWISE
To fit the pedals correctly, you must posion them the correct way around and screw them on in the right direcon:
Sckers indicate the le and right pedal. If these have dropped off, look at the end of the thread where it is imprinted.
The correct pedal needs to be aached to the matching side of the bike i.e. le pedal to le side and right pedal to right side.
IMPORTANT! Pedals need screwing in opposite direcons so they don’t fall off in use.
Le pedal is screwed in an-clockwise / Right pedal is screwed in clockwise. Tighten pedals with spanner provided.
PLEASE MAKE SURE YOU FIT THE CORRECT
PEDAL TO THE CORRECT SIDE. FAILURE TO
DO SO MAY RESULT IN CROSS-THREADING,
WHICH CAN CAUSE IRREPARABLE DAMAGE
NOT COVERED BY WARANTY
i
i
ii
iii
ii iii
THREADS
L R
L
R
LEFT RIGHT
9
5.- FITTING THE REFLECTORS & BELL
TOOLS NEEDED
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
A
First fully release the securing screws as shown
(an-clockwise)
C
Once these are in place, replace the screws and ghten by turning clockwise using a cross-head screwdriver
B
Wrap the bell around the handlebar as shown, remembering
to put it in a place where you can reach it easily whilst riding.
Then wrap the white reflector around the handlebar near the
centre, and wrap the red reflector in the same way around
the saddle post.
BELL RED REFLECTOR WHITE REFLECTOR
HANDLEBAR
(Bell and White Reflector)
SADDLE
(Red Reflector)
CROSS HEAD
SCREWDRIVER
10
6.- FINAL CHECKS
A
C
D
IMPORTANT: ENSURE ALL NUTS / BOLTS / SCREWS ARE TIGHT
RECOMMENDED TORQUES IN OWNER’S MANUAL APPENDIX
PLEASE READ OWNER’S MANUAL BEFORE RIDING THIS BIKE
ALWAYS CHECK BRAKE FUNCTIONALITY BEFORE RIDING
You can now ensure your saddle and handlebars are at a comfortable riding position, and fully tighten. Always be
aware of the minimum insertion mark and make sure these are inserted beyond this point.
This assembly guide is copyrighted to Avocet Sports Limited. Any reproducon, in whole or in part, is strictly forbidden without prior wrien consent.
Check that all bolts and xings are tight and secure. You should do this before every ride.
B
Check tyre pressures regularly. Recommended tyre pressures are clearly marked on the side of the tyre.
Check functionality of brakes before every ride, you will nd out more about this in the user manual included.
TOOLS NEEDED
SPANNER ALLEN KEY
IF YOU ARE EXPERIENCING ANY PROBLEMS PLEASE CALL 03300 904 404 BEFORE RETURNING BIKE TO STORE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Pazzaz 20IN PAZAAZ PETAL HERITAGE BIKE User manual

Brand
Pazzaz
Model
20IN PAZAAZ PETAL HERITAGE BIKE
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents