Crossfire Rover 125 Product information

Brand: Crossfire

Model: Rover 125

Type: Product information

800

DJ431-6A

Sheathing and soldering

100

Battery negative electrode

DJ7021A-2.8-21

DJ621-2.8

R/Y

Relay

DJ431-6A

Electro-starter negative pole

Electric door lock

Bk/W

DJ7041A-2.8-11

DJ611-2.8

100

200

DJ7021A-2.8-21

DJ621-2.8

DJ7021A-2.8-21

DJ621-2.8

Reversing lamp

R/G

Neutral lamp

Be/Y

White = near light Green = negative

Blue = Far Light Brown White =

Front Position Lamp

Brown = Rear Position Lamp

Black = headlamp positive

Yellow and Green = Start Out Line

Yellow Red = Start Power Supply

Green = negative

Black and white = extinguishing line

Left handlebar switch assembly

DJ7031A-2.8-11

DJ611-2.8

Rear lampY/G

Hand rear brake

设计标准化

标记

处数

分区

更改文件号

签名

年.月.日

阶段标记

共页

第页

重量比例

审核

工艺

批准

版本: A/3

永康市尚野工贸有限公司

江烈

250

100

500

300

FU-10A

200

Battery cathode

100

2-DJ431-6A

名称

型号

规格

品号

电缆线

Y45

DJ7031A-2.8-21

DJ621-2.8

DJ7031A-2.8-21

DJ621-2.8

Headlamp

DJ621-D4.8A

Sheathing and soldering

Technical requirements for main cables

1、The finished cable shall not be scratched, broken or loose.The

heat-shrinkable tube on the plug-in should be set in place and

tightly combined with the sheath;

2、The main green and red lines are 4.0mm squared, the red, black

and green lines of the control loop are 0.5mm squared, and the rest

are 0.4mm squared;

3、The color and corresponding position of the line are shown in the

attached drawing;

4、The copper connector and the wire should be firmly pressed, and

can withstand the tension of 5kg, the positive and negative

electrodes of the battery need soldering;

5、The wires of the same plug-in should be aligned;

6、The free length of each plug-in should be sufficient;

7、Copper plug-in, except for special instructions, use 2.8 plug

spring, plug sheet; Copper plug-in material for brass;

8、PVC casing should be added outside the cable, wrapped by electric

rubber, and heat and oil resistance;

9、The conduction rate of the cable is 100%, and there is no short

circuit, break circuit or wrong circuit;

10、Insulation resistance (AC500V) shall be greater than 1.0 megohm,

withstand voltage AC500V/50HZ, no flicker or breakdown within 1

minute;

11、The manufacturer shall label the device number on the flat place

of the device or near the plug-in;

12、All lines with a length of more than 50mm shall be externally

wrapped with plastic PVC sheath or electric adhesive tape. After the

sheath is covered, the dimensions shall be measured from the cable

end of the plug-in. The exposed sheath length of the cable shall not

exceed 20mm. All line bits are viewed from the wired end.

隆鑫125风冷/常规

装配组件

100

Be/W

Bk/Y

Bk/R

CDI Igniter

DJ7061A-2.8-21

DJ621-2.8Bk/W

Y/G

2-∅3.5 Cylindrical socket

DJ221-3.5A

Front brake

Engine Gear Switch

DJ7031A-2.8-11

DJ611-2.8

Magneto

DJ7061A-2.8-11

R/Bk

Be/W

DJ7042-6.3-21

DJ621-E6.3

Rectifier Regulator

DJ7041A-2.8-11

DJ611-2.8

DJ7061A-2.8-11

DJ611-2.8

Bk Bn

Bk/W R/Y

Four Function Left

Hand Switch Assembly

Y/G

Sheathing and soldering

R 250

DJ431-6A

High pressure bag

Bk/Y

DJ621-D6.3A

R/G

Be/Y

Color abbreviation：

Red→R

Black→Bk

Blue→Be

Green→G

White→W

Yellow→Y

Brown→Bn

And for example,

Black and Yellow→Bk/Y,and so on.

Crossfire Rover 125 Product information

Crossfire Rover 125 Product information

Crossfire Rover 125 Product information

Other documents