Crossfire Rover 125 Product information

  • Hello! I am an AI chatbot trained to assist you with the Crossfire Rover 125 Product information. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
800
50
DJ431-6A
Sheathing and soldering
100
Battery negative electrode
Bk
DJ7021A-2.8-21
DJ621-2.8
R/Y
G
Relay
Bk
DJ431-6A
Electro-starter negative pole
50
Electric door lock
G
R
Bk
Bk/W
DJ7041A-2.8-11
DJ611-2.8
50
100
100
200
50
DJ7021A-2.8-21
DJ621-2.8
DJ7021A-2.8-21
DJ621-2.8
Bk
50
50
Reversing lamp
Bk
R/G
Neutral lamp
Be/Y
White = near light Green = negative
Blue = Far Light Brown White =
Front Position Lamp
Brown = Rear Position Lamp
Black = headlamp positive
Yellow and Green = Start Out Line
Yellow Red = Start Power Supply
Green = negative
Black and white = extinguishing line
Left handlebar switch assembly
DJ7031A-2.8-11
DJ611-2.8
Rear lampY/G
Bn
G
Bk
Hand rear brake
设计 标准化
标记
处数
分区
更改文件号
签名
年.月.日
阶段标记
共 页
第 页
重量 比例
审核
工艺
批准
版本: A/3
永康市尚野工贸有限公司
江烈
250
100
100
500
300
FU-10A
200
Battery cathode
100
2-DJ431-6A
名称
型号
规格
品号
电缆线
Y45
Be
W
DJ7031A-2.8-21
DJ621-2.8
DJ7031A-2.8-21
DJ621-2.8
Headlamp
G
Be
DJ621-D4.8A
Sheathing and soldering
Technical requirements for main cables
1、The finished cable shall not be scratched, broken or loose.The
heat-shrinkable tube on the plug-in should be set in place and
tightly combined with the sheath;
2、The main green and red lines are 4.0mm squared, the red, black
and green lines of the control loop are 0.5mm squared, and the rest
are 0.4mm squared;
3、The color and corresponding position of the line are shown in the
attached drawing;
4、The copper connector and the wire should be firmly pressed, and
can withstand the tension of 5kg, the positive and negative
electrodes of the battery need soldering;
5、The wires of the same plug-in should be aligned;
6、The free length of each plug-in should be sufficient;
7、Copper plug-in, except for special instructions, use 2.8 plug
spring, plug sheet; Copper plug-in material for brass;
8、PVC casing should be added outside the cable, wrapped by electric
rubber, and heat and oil resistance;
9、The conduction rate of the cable is 100%, and there is no short
circuit, break circuit or wrong circuit;
10、Insulation resistance (AC500V) shall be greater than 1.0 megohm,
withstand voltage AC500V/50HZ, no flicker or breakdown within 1
minute;
11、The manufacturer shall label the device number on the flat place
of the device or near the plug-in;
12、All lines with a length of more than 50mm shall be externally
wrapped with plastic PVC sheath or electric adhesive tape. After the
sheath is covered, the dimensions shall be measured from the cable
end of the plug-in. The exposed sheath length of the cable shall not
exceed 20mm. All line bits are viewed from the wired end.
隆鑫125风冷/常规
装配组件
100
W
G
Be/W
G
Bk/Y
Bk/R
CDI Igniter
DJ7061A-2.8-21
DJ621-2.8Bk/W
Bk
Y/G
2-3.5 Cylindrical socket
DJ221-3.5A
Front brake
Engine Gear Switch
DJ7031A-2.8-11
DJ611-2.8
W
Magneto
DJ7061A-2.8-11
R/Bk
G
Be/W
Y
DJ7042-6.3-21
DJ621-E6.3
Rectifier Regulator
G
W
Y
R
DJ7041A-2.8-11
DJ611-2.8
DJ7061A-2.8-11
DJ611-2.8
G
Bk Bn
G
Be
W
Bk/W R/Y
Four Function Left
Hand Switch Assembly
Y/G
50
Y/G
Sheathing and soldering
R 250
DJ431-6A
High pressure bag
Bk/Y
G
DJ621-D6.3A
R/G
Be/Y
Color abbreviation:
Red→R
Black→Bk
Blue→Be
Green→G
White→W
Yellow→Y
Brown→Bn
And for example,
Black and Yellow→Bk/Y,and so on.
1/1