EVape EGO-T Operating instructions

Brand: EVape

Model: EGO-T

Type: Operating instructions

EGO-T Starter kit

2 x 650mah rechargeable batteries

2 x EGO-T atomisers

5 x EGO-T empty cartridges

1 x USB charge cable

Other included items within the starter kit can vary please see website for

current offers which will include an updated contents list

Charging your EGO-T electronic starter kit

Plug your USB charge cable that was included with your kit into an available

USB slot which can be found on most electronic devices for example PC, MAC,

Games console, Laptop or a wall charger (available from evape.co.uk). Once

plugged in the LED on the charge cable will turn green, Screw your 650mah

EGO battery into the charging unit and the LED will turn red to indicate that a

charge is needed, once the battery has reached full charge the LED will turn

back to green to indicate that it is now fully charged and ready for use.

Filling your EGO-T tank

Remove the rubber seal cap from an empty tank but do so with care as

damage to the seal cap can lead to leaks. Fill the empty tank with the E-juice of

your choice being careful to not overfill, ensure you leave enough room for the

rubber seal cap to be replaced. Replace the rubber seal cap, to get the best

seal when replacing the rubber seal cap make sure the cap and tank are dry

and free from dirt. Push (do not twist) your freshly filled tank firmly onto the

atomiser (push as far in as it can go, you should hear a click as the pin in the

atomiser pierces the rubber seal cap). Take a couple of dry puffs before

attaching to your battery to ensure E-juice has been pulled through and the

wick is wet before use (you should see air bubbles rising as air replaces the

drawn out e-juice which is a good indicator that it is wicking properly). If you

have trouble getting the tank to pierce when being inserted into the atomiser

use a needle /pin to pierce the seal yourself to start it off this should make it

easier for the atomiser pin to go through. Screw the newly assembled tank and

atomiser onto your battery (ensure the contacts are dry and free from dirt)

and you are ready to vape

Using your EGO-T electronic cigarette

Now you have completed the above you have a fully charged and filled you are

ready to use EGO-T electronic cigarette. The button on the battery is used to

fire the unit which will in turn power the EGO-T atomiser and heats up the

heating coil which then heats the E-juice to produce the vapour “give it a try

now”. The power button has a safety feature which enables you to completely

turn the battery off so when you are not using the EGO-T e-cig it can’t be

accidentally fired. To turn the battery off you simply click the button 5 times in

quick succession and repeat to turn it back on. Do not over puff on the unit as

this overheats the unit which leads to melting the seals so please try (as hard

as it is to put down) letting your new kit rest in between puffs. When the

battery needs to be recharged the light on the battery of the EGO-T will flash

every time you attempt to use it and will not fire so recharge following the

above instructions. As you are using the EGO-T occasionally tilt it back and

forth to ensure the E-juice is being soaked into the wicking material this will

stop you possibly using the unit dry and will stop you possibly burning the wick.

When you E-juice level starts to get low and you want to refill always remove

the atomiser and tank from the battery and repeat the filling instructions

above to avoid accidentally flooding your battery. Always keep external parts

and screw threads on both the battery and atomiser clean, dry and free from

dirt.

Cleaning the EGO-T

To clean out your EGO-T unscrew the atomiser and tank assembly from the

battery and empty any excess E-juice, run hot water into the tank and shake

and empty repeatedly until you are satisfied that the tank is suitably clean

repeat with the atomiser (never attempt to clean the tank and atomiser whilst

attached to the battery). Shake out any excess water and make sure the unit is

dry before re-using. A common problem after cleaning is that the unit has not

been dried completely and may appear to no longer produce vapour, this is

because the wicking material is still wet and has absorbed water which will

have to be replaced with E-juice as water does not produce vapour, taking a

few vapes once filled with E-juice will normally take care of this as the water is

evaporated and E-juice has absorbed back into the wicking material.

If there is anything you need/want to know about the EGO-T that has not

been covered in this guide feel free to contact us and we will be glad to

answer any questions and/or provide the help you need

EVape EGO-T Operating instructions

Brand: EVape

Model: EGO-T

Type: Operating instructions

Download PDF

report

EVape EGO-T Operating instructions

EVape EGO-T Operating instructions

Other documents