Page is loading ...
EGO-T Starter kit
2 x 650mah rechargeable batteries
2 x EGO-T atomisers
5 x EGO-T empty cartridges
1 x USB charge cable
Other included items within the starter kit can vary please see website for
current offers which will include an updated contents list
Charging your EGO-T electronic starter kit
Plug your USB charge cable that was included with your kit into an available
USB slot which can be found on most electronic devices for example PC, MAC,
Games console, Laptop or a wall charger (available from evape.co.uk). Once
plugged in the LED on the charge cable will turn green, Screw your 650mah
EGO battery into the charging unit and the LED will turn red to indicate that a
charge is needed, once the battery has reached full charge the LED will turn
back to green to indicate that it is now fully charged and ready for use.
Filling your EGO-T tank
Remove the rubber seal cap from an empty tank but do so with care as
damage to the seal cap can lead to leaks. Fill the empty tank with the E-juice of
your choice being careful to not overfill, ensure you leave enough room for the
rubber seal cap to be replaced. Replace the rubber seal cap, to get the best
seal when replacing the rubber seal cap make sure the cap and tank are dry
and free from dirt. Push (do not twist) your freshly filled tank firmly onto the
atomiser (push as far in as it can go, you should hear a click as the pin in the
atomiser pierces the rubber seal cap). Take a couple of dry puffs before
attaching to your battery to ensure E-juice has been pulled through and the
wick is wet before use (you should see air bubbles rising as air replaces the
drawn out e-juice which is a good indicator that it is wicking properly). If you
have trouble getting the tank to pierce when being inserted into the atomiser
use a needle /pin to pierce the seal yourself to start it off this should make it
easier for the atomiser pin to go through. Screw the newly assembled tank and
atomiser onto your battery (ensure the contacts are dry and free from dirt)
and you are ready to vape
Using your EGO-T electronic cigarette
Now you have completed the above you have a fully charged and filled you are
ready to use EGO-T electronic cigarette. The button on the battery is used to
fire the unit which will in turn power the EGO-T atomiser and heats up the
heating coil which then heats the E-juice to produce the vapour “give it a try
now”. The power button has a safety feature which enables you to completely
turn the battery off so when you are not using the EGO-T e-cig it can’t be
accidentally fired. To turn the battery off you simply click the button 5 times in
quick succession and repeat to turn it back on. Do not over puff on the unit as
this overheats the unit which leads to melting the seals so please try (as hard
as it is to put down) letting your new kit rest in between puffs. When the
battery needs to be recharged the light on the battery of the EGO-T will flash
every time you attempt to use it and will not fire so recharge following the
above instructions. As you are using the EGO-T occasionally tilt it back and
forth to ensure the E-juice is being soaked into the wicking material this will
stop you possibly using the unit dry and will stop you possibly burning the wick.
When you E-juice level starts to get low and you want to refill always remove
the atomiser and tank from the battery and repeat the filling instructions
above to avoid accidentally flooding your battery. Always keep external parts
and screw threads on both the battery and atomiser clean, dry and free from
dirt.
Cleaning the EGO-T
To clean out your EGO-T unscrew the atomiser and tank assembly from the
battery and empty any excess E-juice, run hot water into the tank and shake
and empty repeatedly until you are satisfied that the tank is suitably clean
repeat with the atomiser (never attempt to clean the tank and atomiser whilst
attached to the battery). Shake out any excess water and make sure the unit is
dry before re-using. A common problem after cleaning is that the unit has not
been dried completely and may appear to no longer produce vapour, this is
because the wicking material is still wet and has absorbed water which will
have to be replaced with E-juice as water does not produce vapour, taking a
few vapes once filled with E-juice will normally take care of this as the water is
evaporated and E-juice has absorbed back into the wicking material.
If there is anything you need/want to know about the EGO-T that has not
been covered in this guide feel free to contact us and we will be glad to
answer any questions and/or provide the help you need
/
