red lion DA 4G LTE CAT1 Sled User manual

Brand: red lion

Model: DA 4G LTE CAT1 Sled

Type: User manual

DA_4GLTE_Cat1 - B

Drawing No. LP1141

Released 07/2020

DA 4G LTE CAT1 Sled

Installation Guide

PACKAGE CHECKLIST

This product package should contain the items listed below. If

any items are missing or damaged, contact Red Lion immediately.

- DA 4G LTE CAT1 Sled

- Installation Guide

SAFETY SUMMARY

All safety related regulations, local codes as well as instructions

that appear in this document or on equipment must be observed

to ensure personal safety and to prevent damage to either the

device or equipment connected to it.

Do not use these products to replace proper safety interlocking.

No software-based device (or any other solid-state device) should

ever be designed to be responsible for the maintenance of

personnel safety or consequential equipment not equipped with

safeguards. Red Lion disclaims any responsibility for damages,

either direct or consequential, that result from the use of this

equipment in a manner not consistent with these specifications.

SPECIFICATIONS

1. POWER REQUIREMENTS: Power is supplied by the DA host

controller.

Max Power: 3 W

2. CELLULAR FREQUENCY SPECIFICATIONS:

TECHNOLOGY BANDS

ANTENNA

CONFIGURATION *

Telstra

LTE

1, 3, 5, 8, 9, 18,

19, 26, 28

MIMO Required

3G (fallback)

1, 5, 6, 8, 19

Diversity Supported

* GPS antenna MUST be an active antenna.

4. INTERFACES:

Cellular: Two SMA Connectors

GPS: One SMA Connector

5. GPS:

GNSS Supported: GPS L1, GLONASS L1, Galileo E1 and

BeiDouB1

High RF Sensitivity plus jamming detection

6. WIRELESS/CARRIER COMPLIANCE

Telstra

7. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range: -40 to 75 °C

Storage Temperature Range: -40 to 80 °C

Vibration to IEC 60068-2-6: Operational 5-500 Hz, 2 g

Shock to IEC 60068-2-27: Operational 15 g

Operating and Storage Humidity: 0 to 95% max. RH non-

condensing

Altitude: Up to 2000 meters

8. CERTIFICATIONS AND COMPLIANCES:

Refer to the controller manual for agency certifications.

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

IEC/EN 61010-1

RoHS Compliant

9. ANTENNA CONNECTOR:

One front panel SMA-A main antenna connection

One front panel SMA-A GPS antenna connection

One front panel SMA-A Diversity antenna connection.

10. INSTALLATION REQUIREMENTS: Sled must be installed

inside the unit case with the hardware provided. See

“Installing the 4G LTE CAT1 Sled” for more details.

11. WEIGHT: 3.2 oz (90.7 g)

CAUTION: Risk of Danger

Read complete instructions prior to installation and

operation of the unit.

ATTENTION : Risque de danger

Lire les instructions complètes avant l’installation et

l’utilisation de l’appareil.

z 4G LTE CAT1 cellular communication

z Dual-SIM card slots for carrier fail-over

z Industrial rated for harsh environments

z Wide operating temperature range

z Built-in GPS for asset monitoring

z Simplified deployment architecture

z Field installable

For use with DA50 and DA70 series covered in DEMKO 20 ATEX

2268X and IECEx UL 20.0007X certificates

Drawing No. LP1141 Released 07 2020

SIM CARD INSTALLATION & DETAILS

A SIM Card with data plan enabled has to be installed on the

DA 4G LTE CAT1 Sled before installing the sled in the DA50 or

DA70 host device. Contact your cellular provider (carrier) and

request a data account. For LTE, the carrier should provide you

with a SIM card (size: 2FF) to insert into the DA 4G LTE CAT1

Sled, along with the APN, username & password for data

connectivity as required.

Insert the SIM card(s) into the card cradle on the sled.

a. Open the cradle by sliding the

cover latch to the right.

b. Lift the edge of the cradle

upward, and insert the SIM

card into the raised hinge of

SIM card slot 1 with the

contacts facing left and the

SIM card corner notch facing

away from the sled.

c. Close the cradle cover and

slide the cover latch to the left

until it clicks to secure the SIM

card in position.

d. Verify that the SIM corner

notch lines up correctly and

the SIM is flush.

e. Repeat this step if a second

SIM is used in your application.

INSTALLING THE 4G LTE CAT1 SLED

DA50 INSTALLATION

1. Prior to installing the Sled for your DA50 application, ensure

that the unit is not receiving power.

2. Disconnect and remove your DA50 from the DIN rail.

3. Remove the DA50 unit’s front cap by squeezing the sides and

pulling.

4. Slide out the sled holder.

5. Install the sled into the sled holder and hand tighten the

captive fasteners, or use a screwdriver.

6. Re-install the sled holder containing the sled into the

Gateway. Make sure it is fully seated.

7. Replace the front cap.

DA70 INSTALLATION

It is recommended that the Cellular Sled be installed into the

topmost Sled slot in the carriage of the Controller.

1. Prior to installing the Sled(s) for your DA70 Controller

application, ensure that the Controller is not receiving power.

2. Remove the carriage from the Controller case by releasing the

two retaining latches and pulling straight out from Controller.

3. Remove blank panel from the carriage slot of the target sled

installation location.

4. Install sled by aligning the two sled mounting hole fasteners,

with the controller mounting posts. Be sure locating holes on

bottom side of sled align with the locating pins on the

carriage, and the sled sits flush against the carriage.

5. Hand tighten the sled captive fasteners, or use a screwdriver

if necessary.

6. Repeat the above steps for any additional sleds.

7. Carefully align the carriage with Controller base and press

carriage into the controller.

8. Close the retaining latches to ensure the carriage is fully

seated into the Controller case.

CONFIGURING THE DA 4G LTE CAT1 SLED

SOFTWARE CONFIGURATION

The CAT1 Model Sled (Cell Modem Sled) can be configured

using Crimson 3.2 (or later) software. After selecting the Cellular

Modem type in the Sled Hardware Configuration and applying

the hardware changes, the modem properties are visible in the

Network Interfaces section of the System Configuration. Find

additional information in the Crimson 3.2 Software Manual.

GUI CONFIGURATION

When using the Cellular Sled in your installation, verify cellular

connectivity through the GUI System page after logging into the

DA50A Gateway. Here you can view the connection status and

verify signal strength. More detailed diagnostic information can

be viewed from the System/Diagnostic/Sled Status/Cell Modem

Status page.

For further configuration and troubleshooting information,

please refer to the Software Manual for troubleshooting steps at

www.redlion.net/support/documentation.

ANTENNA INSTALLATION

Antennas intended for use in Class 1, Division 2 and Zone 2

Hazardous Locations must be installed within the end use

enclosure. For remote mounting in an unclassified location,

routing and installation of the antennas shall be in accordance

with the National Electrical Codes requirements.

CAUTION: Follow standard ESD precautionary

procedures.

ATTENTION: Suivez les procédures de précaution

standard de décharge électrostatique.

WARNING - Disconnect all power to the unit before

installing or removing sleds.

AVERTISSEMENT - Débranchez l’alimentation électrique

de l’appareil avant d’installer ou de retirer les tiroirs.

CAUTION: Failure to properly align the carriage can

result in damage to the Sled connector pins.

ATTENTION: Si le chariot n’est pas correctement

aligné, les broches du connecteur du chariot

risquent d’être endommagées.

Released 07 2020 Drawing No. LP1141

LEDs

PWR LED - Power Status 4G LTE CAT14 Sled

The PWR LED provides status for both Sled power as well as

GPS antenna errors. Refer to the software user manual for more

detailed information of possible LED statuses.

COLOR STATUS

Off No power to the sled

Green Sled is powered.

Orange Sled is powered and a GPS antenna fault is detected.

Note: A GPS antenna fault will be present with a passive antenna or

antenna short.

STS LED

The STS LED provides status for the modem. Refer to the

software user manual for more detailed information of possible

LED statuses.

COLOR STATUS

Off Modem resetting

Blinking Green Normal operation (1 sec on; 2 sec off)

Solid Green Modem setup

RED LION CONTROLS TECHNICAL SUPPORT

If for any reason you have trouble operating, connecting, or

simply have questions concerning your new unit, contact Red

Lion’s technical support.

Support: support.redlion.net

Website: www.redlion.net

Inside US: +1 (877) 432-9908

Outside US: +1 (717) 767-6511

Red Lion Controls, Inc.

20 Willow Springs Circle York, PA 17406

ORDERING INFORMATION

PART NUMBER DESCRIPTION

DAS00CL9C1SAZ000 4G LTE CAT1 Sled with Telstra Support

ACCESSORIES

PART NUMBER DESCRIPTION

ANTMA741ABI001

2G/3G/4G LTE MIMO low profile direct

permanent mount antenna, IP67 rated

ANTMA710AABI001

2G/3G/4G LTE MIMO plus GPS direct

permanent mount antenna, IP67 rated

Connector/Cables for Antennas

Both: LTE and cellular (both lines) have SMA male CFD-200 low loss

cable (3 meters)

ANTMA71: GPS has SMA male RG-174 (3 meters)

All other company and product names are trademarks of their respective owners.

LIMITED WARRANTY

(a) Red Lion Controls Inc. (the “Company”) warrants that all Products shall be free from defects in material and

workmanship under normal use for the period of me provided in “Statement of Warranty Periods” (available at

www.redlion.net) current at the me of shipment of the Products (the “Warranty Period”). EXCEPT FOR THE

ABOVE-STATED WARRANTY, COMPANY MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE

PRODUCTS, INCLUDING ANY (A) WARRANTY OF MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY

RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE

OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. Customer shall be responsible for determining that a

Product is suitable for Customer’s use and that such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a

result of Customer’s failure to store, install, commission or maintain the Product according to specicaons; (ii)

Customer alters or repairs such Product without the prior wrien consent of Company.

sole discreon, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that,

if Company so requests, Customer shall, at Company’s expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER’S SOLE AND EXCLUSIVE

REMEDY AND COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET

FORTH IN PARAGRAPH (a).

BY INSTALLING THIS PRODUCT, YOU AGREE TO THE TERMS OF THIS WARRANTY, AS WELL AS ALL OTHER

DISCLAIMERS AND WARRANTIES IN THIS DOCUMENT.

red lion DA 4G LTE CAT1 Sled User manual

red lion DA 4G LTE CAT1 Sled User manual

red lion DA 4G LTE CAT1 Sled User manual

Related papers

Other documents