ClearOne BMA CT Installation guide

ClearOne
Brand
ClearOne
Model
BMA CT
Type
Installation guide

This manual is also suitable for

ClearOne BMA CT - BMA CTH Recessed Mount allows you to flush-mount your BMA CT or BMA CTH in solid or non-dropped ceilings, which provides a professional finished look. It is easy to assemble and fits both the BMA CT and BMA CTH. The kit includes an aluminum frame, screws, and comes in two different sizes - 24 inches and 600 mm - to accommodate local design standards.

ClearOne BMA CT - BMA CTH Recessed Mount allows you to flush-mount your BMA CT or BMA CTH in solid or non-dropped ceilings, which provides a professional finished look. It is easy to assemble and fits both the BMA CT and BMA CTH. The kit includes an aluminum frame, screws, and comes in two different sizes - 24 inches and 600 mm - to accommodate local design standards.

It’s All About the Architecture!
TM
1
> Material
• 6063-T5 Aluminum Alloy
> Dimensions
• 24 IN: 25.46 x 25.46 x 1.60 in
• 600 mm: 639 x 639 x 41.0 mm
> Color
• White
> Components
• Aluminum frame (4)
• Screws (8)
> Part Numbers
• 910-3200-212 BMA RECESSED MOUNT KIT 24 IN
• 910-3200-212-I BMA RECESSED MOUNT KIT 600MM
BMA RECESSED-MOUNT KIT
ACCESSORIES
AUDIO
CONFERENCING
The BMA Recessed-Mount Kit allows for a ush-mount of a BMA
in solid or non-dropped ceilings. The kit provides a professional,
nished look when installed in a drywall ceiling. Easy to assem-
ble, it ts the BMA CT and and BMA CTH. 24 inch and 600 mm
models are available to accommodate local design standards.
2
BMA RECESSED-MOUNT KIT
Dimensions
Part Number L W Rough-in Cut Out A
24 IN 910-3200-212 25.46 in
(646.8 mm)
25.46 in
(646.8 mm)
24.88 x 24.88 in
(632 x 632 mm)
1.61 in
(41.0 mm)
600 MM 910-3200-212-I 639.0 mm
(25.16 in)
639.0 mm
(25.16 in)
625 x 625 mm
(24.61 x 24.61 in)
41.0 mm
(1.61 in)
Other product names and logos may be registered trademarks of their respective owners who do not neces-
sarily endorse ClearOne or ClearOne’s products. All rights reserved. Information in this document subject to
change without notice. QSG-0098-001 v1.0 September 2020 ©2020 ClearOne.
SALES AND INQUIRIES
Headquarters
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
US & Canada
Tel: 801.975.7200
Fax: 801.303.5711
International
Tel: +1.801.975.7200
[email protected]
Tech Support
Tel: 801.974.3760
[email protected]
Sales
Tel: 801.975.7200
[email protected]
3
Included Components:
• Frame piece with holes (2)
• Frame piece w/o holes (2)
• M3.5X12 self-tapping screw (8)
With the M3.5X12 screws, attach the 4 frame pieces at
each corner.
To install the recessed mount kit, assemble the frame, attach the frame to building structure, then
place the BMA in the frame.
The instructions below explain two methods to attach the frame to building structure: cabling and
wood blocking.
Assemble the Frame
With Cabling
Attach the Frame to Building Structure
Lift the BMA into the inside of the frame and place it so it rests on the recessed edges of the frame.
Important!
• Examine shipment and
report damage to your
transportation carrier.
• Install in accordance with
all applicable national and
local codes.
• Ensure that power is
off before you start
installation.
Installation
BMA RECESSED-MOUNT KIT
With Wood Blocking
Place the BMA in the Frame
Warning! Wood blocking must be independently
supported by building structure.
  • Page 1 1
  • Page 2 2
  • Page 3 3

ClearOne BMA CT Installation guide

ClearOne
Brand
ClearOne
Model
BMA CT
Type
Installation guide
This manual is also suitable for

ClearOne BMA CT - BMA CTH Recessed Mount allows you to flush-mount your BMA CT or BMA CTH in solid or non-dropped ceilings, which provides a professional finished look. It is easy to assemble and fits both the BMA CT and BMA CTH. The kit includes an aluminum frame, screws, and comes in two different sizes - 24 inches and 600 mm - to accommodate local design standards.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents