Toro Dingo TX 1300 Track Loader User manual

Form No. 3438-963 Rev D

TX 1300 Compact T ool Carrier

Model No. 22370 —Serial No. 400000000 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3438-963*

This product complies with all relevant European

directives; for details, please see the separate product

specic Declaration of Conformity (DOC) sheet.

It is a violation of California Public Resource Code

Section 4442 or 4443 to use or operate the engine on

any forest-covered, brush-covered, or grass-covered

land unless the engine is equipped with a spark

arrester , as dened in Section 4442, maintained in

ef fective working order or the engine is constructed,

equipped, and maintained for the prevention of re.

The enclosed engine owner's manual is supplied

for information regarding the US Environmental

Protection Agency (EP A) and the California Emission

Control Regulation of emission systems, maintenance,

and warranty . Replacements may be ordered through

the engine manufacturer .

W ARNING

CALIFORNIA

Proposition 65 W arning

Diesel engine exhaust and some of its

constituents are known to the State of

California to cause cancer , birth defects,

and other reproductive harm.

Battery posts, terminals, and related

accessories contain lead and lead

compounds, chemicals known to

the State of California to cause

cancer and reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This machine is a compact tool carrier intended for

use in various earth and materials moving activities for

landscaping and construction work. It is designed to

operate a wide variety of attachments each of which

perform a specialized function. Using this product

for purposes other than its intended use could prove

dangerous to you and bystanders. Do not modify the

machine or attachments.

This machine should be operated, serviced, and

repaired only by professionals familiar with its

characteristics and acquainted with the relevant safety

procedures.

Operate this machine in ambient temperatures from

-18 to 38°C (0 to 100 °F). Contact your Authorized

Service Dealer for provisions required for operating

in extreme temperatures.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g362307

Figure 1

1. Model and serial number location

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in the USA

This manual identies potential hazards and has

safety messages identied by the safety-alert symbol

(Figure 2 ), which signals a hazard that may cause

serious injury or death if you do not follow the

recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important calls attention to special mechanical

information and Note emphasizes general information

worthy of special attention.

Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

InfoCenter Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Performing Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 20

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Driving the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Shutting Of f the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Understanding the Smart Load System . . . . . . . . . . . . . 25

Diesel Particulate Filter (DPF)

Regeneration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Retrieving a Stuck Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Moving a Non-Functioning Machine . . . . . . . . . . . . . . . . . . 36

Hauling the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Lifting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Recommended Maintenance Schedule(s) . . . . . . . . . . . 40

Pre-Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Using the Cylinder Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Accessing Internal Components . . . . . . . . . . . . . . . . . . . . . . . 43

Removing the Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Removing the Front Cover Assembly . . . . . . . . . . . . . . . . 45

Removing the Side Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Greasing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Engine Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Servicing the Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Servicing the Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Servicing the Diesel-Oxidation Catalyst

(DOC) and the Soot Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Draining the W ater Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Replacing the W ater Separator Filter . . . . . . . . . . . . . . . . 50

Checking the Fuel Lines and

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Replacing the Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Bleeding the Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Draining the Fuel T ank(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Electrical System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Using the Battery-Disconnect Switch . . . . . . . . . . . . . . . . 51

Servicing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Jump-Starting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Servicing the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Drive System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Servicing the T racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Cooling System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Cooling System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Servicing the Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Changing the Engine Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Belt Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Checking the Alternator-Belt T ension . . . . . . . . . . . . . . . . 60

Controls System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Adjusting the Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Hydraulic System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Hydraulic System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Relieving Hydraulic Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Hydraulic Fluid Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Checking the Hydraulic-Fluid Level . . . . . . . . . . . . . . . . . . . 62

Replacing the Hydraulic Filters . . . . . . . . . . . . . . . . . . . . . . . . . 63

Changing the Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Loader Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

T orquing the Loader Arm Adjustment

Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Removing Debris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

W ashing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Cleaning the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

3

Safety

General Safety

DANGER

There may be buried utility lines in the work

area. Digging into them may cause a shock

or an explosion.

Have the property or work area marked for

buried lines and do not dig in marked areas.

Contact your local marking service or utility

company to have the property marked (for

example, in the US, call 81 1 or in Australia,

call 1 100 for the nationwide marking service).

Always follow all safety instructions to avoid serious

injury or death.

•Do not exceed the rated operating capacity , as the

machine may become unstable, which may result

in loss of control.

•Do not transport a load with the arms raised or

extended; always transport loads close to the

ground, with the loader arms retracted.

•Slopes are a major factor related to loss-of-control

and tip-over accidents, which can result in severe

injury or death. Operating the machine on any

slope or uneven terrain requires extra caution.

•Operate the machine up and down slopes

with the heavy end of the machine uphill and

the load close to the ground and the loader

arms retracted. W eight distribution changes with

attachments. An empty load-bearing attachment

makes the rear of the machine the heavy end,

and a full load-bearing attachment makes the

front of the machine the heavy end. Most other

attachments make the front of the machine the

heavy end.

•Have the property or work area marked for buried

lines and other objects, and do not dig in marked

areas.

•Read and understand the content of this Operator ’ s

Manual before starting the engine.

•Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

•Never allow children or untrained people to

operate the machine.

•Keep your hands and feet away from the moving

components and attachments.

•Do not operate the machine without the guards

and other safety protective devices in place and

working on the machine.

•Keep bystanders and pets away from the machine.

•Stop the machine, shut of f the engine, and remove

the key before servicing, fueling, or unclogging

the machine.

Improperly using or maintaining this machine can

result in injury . T o reduce the potential for injury ,

comply with these safety instructions and always

pay attention to the safety-alert symbol , which

means Caution, W arning, or Danger—personal safety

instruction. Failure to comply with these instructions

may result in personal injury or death.

4

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decalbatterysymbols

Battery Symbols

Some or all of these symbols are on your battery .

1. Explosion hazard 6. Keep bystanders away

from the battery .

2. No re, open ame, or

smoking

7. W ear eye protection;

explosive gases can

cause blindness and other

injuries.

3. Caustic liquid/chemical

burn hazard

8. Battery acid can cause

blindness or severe burns.

4. W ear eye protection. 9. Flush eyes immediately

with water and get medical

help fast.

5. Read the Operator's

Manual .

10. Contains lead; do not

discard

decal93-6681

93-6681

1. Cutting/dismemberment hazard, fan—stay away from

moving parts.

decal93-7814

93-7814

1. Entanglement hazard, belt—stay away from moving parts;

keep all guards and shields in place.

decal1 15-2047

1 15-2047

1. W arning—do not touch the hot surface.

decal1 15-4855

1 15-4855

1. Hot surface/burn hazard—wear protective gloves when

handling the hydraulic couplers and read the Operator's

Manual for information on handling hydraulic components.

decal1 15-4857

1 15-4857

1. Lower the loader arms.

4. Curl the bucket.

2. Dump the bucket. 5. Float the bucket on the

ground.

3. Raise the loader arms.

decal1 15-4858

1 15-4858

1. Crushing hazard of hands or feet—install the cylinder lock.

decal1 15-4865

1 15-4865

1. Engine coolant

2. Read the Operator's

Manual .

5

decal1 17-3276

1 17-3276

1. Engine coolant under

pressure

3. W arning—do not touch the

hot surface.

2. Explosion hazard—read

the Operator's Manual .

4. W arning—read the

Operator's Manual .

decal120-0625

120-0625

1. Pinch point, hand—keep hands away .

decal122-1925

122-1925

1. T orque to 2.82 to 3.16 N∙m (25 to 28 in-lb)

decal125-4967

125-4967

1. Lift point

decal125-6694

125–6694

1. T ie down location

decal125-8483

125-8483

1. Hydraulic uid; read the Operator ’ s Manual .

6

decal131-8026

131-8026

1. Battery

power—disconnect

3. On

2. Of f 4. Read the Operator's

Manual .

decal133-8062

133-8062

decal137-5409

137-5409

decal139-1 158

139-1 158

1. Crushing hazard, from above, and pinching hazard—stay

away from the bucket and loading arms.

decal139-1 159

139-1 159

1. W arning—keep bystanders away .

decal139-1 162

139-1 162

1. W arning—read the

Operator ’ s Manual for

the bucket maximum

weight limit.

2. T ipping hazard—do not

drive the machine with the

load raised or the arms

extended; carry the load

close to the ground with

the arms retracted when

driving.

decal139-1 164

139-1 164

1. Crushing hazard from above, falling load—ensure that the

quick-attach levers are locked.

7

decal139-1 173

139-1 173

1. High-pressure uid hazard, injection into the body—read

the Operator ’ s Manual before performing maintenance.

decal145-4273

145-4273

1. Retract the hydraulic

cylinder (optional)

4. Extend the arms

(telescoping model only)

2. Extend the hydraulic

cylinder (optional)

5. Attachment

ow—Reverse

3. Attachment ow—Forward

6. Retract the arms

(telescoping model only)

decal145-4274

145-4274

1. Read the Operator ’ s

Manual before performing

maintenance.

9. Engine oil

2. Check every 8 hours

10. Engine coolant

3. Fuel

1 1. Hydraulic uid

4. Grease points

12. Fluids

5. Engine air lter 13. Capacity

6. Safety air lter 14. Fluid interval (hours)

7. Engine oil level

15. Filter interval (hours)

8. Belt tension

8

decal131-0708

131-0708

1. Move forward

3. Move rearward

2. T urn left

4. T urn right

decal144-4253

144-4253

1. Parking brake—engaged 5. Engine—stop

2. Parking brake—disengaged 6. Engine—run

3. Fast 7. Engine—start

4. Slow

8. Horn

9

decal145-0637

145-0637

1. W arning—read the Operator's Manual . 7. Cutting/severing hazard of hand or foot—wait for all moving

parts to stop before servicing; keep away from moving parts;

keep all guards and shields in place.

2. W arning—receive training before operating the machine.

8. Explosion hazard; electrocution hazard—call the local utilities

hotline before beginning work in an area.

3. W arning—wear hearing protection.

9. Crushing hazard—keep away from the attachment when

operating the machine; keep bystanders away from the

machine.

4. W arning—engage the parking brake, lower the attachment to

the ground, shut of f the engine, and remove the key from the

ignition before leaving the machine.

10. T ipping hazard—always move up or down slopes with

the attachment lowered; never drive on a slope with the

attachment raised; always operate with the heavy end uphill;

always carry loads low; never jerk the control levers; use

a steady , even motion.

5. Electrocution hazard, power lines—check for power lines in

the area before using the machine.

1 1. T ipping hazard—do not make fast turns; always check behind

you before reversing the machine.

6. Crushing hazard—install the cylinder lock; read the Operator's

Manual before servicing or performing maintenance.

10

Product Overview

g318043

Figure 3

1. Hood 5. Lower loader arm

9. Control panel

13. Fuel gauge

2. Auxiliary hydraulic couplers 6. Upper loader arm 10. Hydraulic tank 14. T ie-down point

3. Mount plate 7. T rack 1 1. Auxiliary hydraulics lock

switch

15. Fuel tank

4. Lift point 8. Cylinder lock 12. Operator platform

1 1

Controls

Control Panel

Become familiar with all the controls before you start

the engine and operate the traction unit.

g318044

Figure 4

1. Plug for optional kit

7. Key switch

2. Parking brake switch 8. Horn

3. Reference bar

9. Loader-valve lock

4. InfoCenter Display 10. Loader arm/attachment-tilt

lever

5. Power socket 1 1. Joystick controls

6. Throttle switch 12. T raction control

Key Switch

The key switch, used to start and shut of f the engine,

has 3 positions: O FF , R UN , and S TART .

Parking-Brake Switch

Press the parking-brake switch to engage and

disengage the parking brake. The parking brake also

engages automatically when you shut of f the machine.

Throttle Switch

Hold the switch forward for 2 or more seconds to set

the throttle at HIGH IDLE; hold the switch rearward for

2 or more seconds to set the throttle at LOW IDLE;

or momentarily press the switch in either direction to

increase or decrease the engine speed in smaller

increments.

Reference Bar

When driving the traction unit, use the reference bar

as a handle and a leverage point for controlling the

traction control and the joystick lever . T o ensure

smooth, controlled operation, do not take your hands

of f the reference bars while operating the machine.

T raction Control

g029289

Figure 5

1. Reference bar

2. T raction control

•T o move forward, move the traction control

forward.

g264830

Figure 6

•T o move rearward, move the traction control

rearward.

Important: When reversing, look behind you

for obstructions and keep your hands on the

reference bar .

g264831

Figure 7

12

•T o turn right, rotate the traction control clockwise.

g264833

Figure 8

•T o turn left, rotate the traction control

counterclockwise.

g264832

Figure 9

•T o stop the machine, release the traction control.

Note: The farther you move the traction control in

any direction, the faster the machine moves in that

direction.

Loader Arm/Attachment-T ilt Lever

Slowly move the lever to operate the loader arms and

tilt the attachment.

Note: The detent (oat) position allows attachments

such as the leveler and the hydraulic blade to follow

the contours of the ground (i.e., oat) when grading.

g358629

Figure 10

1. Detent (oat)

position—push the lever

fully forward.

4. T ilt the attachment

rearward.

2. Lower the loader arms. 5. T ilt the attachment

forward.

3. Raise the loader arms.

By moving the lever to an intermediate position (e.g.,

forward and left), you can move the loader arms and

tilt the attachment at the same time.

13

Loader-V alve Lock

The loader-valve lock secures the loader

arm/attachment-tilt lever so that you cannot push it

forward. This helps to ensure that no one accidentally

lowers the loader arms during maintenance. Secure

the loader valve with the lock, in addition to the

cylinder locks, any time you need to shut of f the

machine with the loader arms raised. Refer to Using

the Cylinder Locks ( page 42 ) .

T o set the lock, lift it so that it clears the hole in the

control panel and swing in front of the loader-arm

lever . Push it down into the locked position.

g358630

Figure 1 1

1. Loader-valve lock

Joystick Controls

g318281

Figure 12

1. Attachment primary

function (hydraulic

attachments only)

3. Extend and retract the

loader arms

2. Attachment secondary

function (certain

attachments only)

Note: The loader arms may not extend when they

are fully raised due to trapped pressure; lower the

arms slightly to relieve pressure and extend them.

W ARNING

Moving the machine while the loader arms

are extended may affect the stability of the

machine.

Minimize machine movement while the loader

arms are extended.

Auxiliary-Hydraulics Lock Switch

Engage the forward or reverse hydraulics, then use

your right foot to press the lock switch to continue the

ow and free your hand for other controls.

g358628

Figure 13

1. Auxiliary-hydraulics lock switch

14

Fuel Gauge

This gauge measures the amount of fuel in the fuel

tank(s).

g371278

Figure 14

InfoCenter Display

The InfoCenter LCD display shows information about

your machine, such as the operating status, various

diagnostics and other information about the machine.

There is a splash screen and main information screen

of the InfoCenter . Y ou can switch between the splash

screen and main information screen at any time by

pressing any of the InfoCenter buttons and then

selecting the appropriate directional arrow .

g264015

Figure 15

1. Indicator light 3. Middle button

2. Right button

4. Left button

•Left Button, Menu Access/Back Button—press this

button to access the InfoCenter menus. Y ou can

use it to exit any menu that you are currently using.

•Middle Button—use this button to scroll down

menus.

•Right Button—use this button to open a menu

where a right arrow indicates additional content.

Note: The purpose of each button may change

depending on what is required at the time. Each

button is labeled with an icon displaying its current

function.

InfoCenter Icon Descriptions

Menu access

Scroll down

Enter

Change the next value in the

list

Increase

Decrease

Save value

Exit menu

Accept

The option is locked.

Hour meter

Adjust digit

W arning

T ransport-speed screen

access

Fast

Slow

Neutral

Auxiliary lock

Cold start

15

InfoCenter Icon Descriptions (cont'd.)

Parking brake

Engine

Glow plugs

Engine-coolant temperature

Engine speed

Battery voltage

Smart Load is active.

Indicates when scheduled

service should be performed

DPF regeneration is required.

A parked or recovery

regeneration is processing.

High exhaust temperature

NOx control diagnosis

malfunction; drive the machine

back to the shop and contact

your Authorized Service

Dealer .

Using the Menus

T o access the InfoCenter menu system, press the

menu access button while at the main screen.

This will bring you to the main menu. Refer to the

following tables for a synopsis of the options available

from the menus:

Main Menu

Menu Item Description

Faults The Faults menu contains

a list of the recent machine

and engine faults. Refer to

the Service Manual or your

Authorized Service Dealer for

more information on the Faults

menu and the information

contained there.

Service The Service menu contains

information on the machine

such as hours of use and other

similar numbers.

Diagnostics The Diagnostics menu

displays the state of each

machine switch, sensor and

control output. Y ou can use

this to troubleshoot certain

issues as it will quickly tell you

which machine controls are on

and which are of f.

Settings The Settings menu allows

you to customize and modify

conguration variables on the

InfoCenter display .

About The About menu lists the

model number , serial number ,

and software version of your

machine.

16

Service

Menu Item Description

Hours

Lists the total number of hours

that the machine, engine, and

auxiliary hydraulics have been

on, as well as the number of

hours for engine service and

hydraulic service.

Counts Lists the number of starts that

the machine has experienced,

the number of times the

machine has warned that the

engine temperature is too

high, and the number of times

the engine has shut of f due to

high temperatures.

DPF Regeneration The DPF regeneration option

and DPF submenus.

Inhibit Regen Use to control reset

regeneration.

Parked Regen Use to initiate a parked

regeneration.

Last Regen Lists the number hours since

the last reset, parked, or

recovery regeneration.

Recover Regen Use to initiate a recovery

regeneration.

Diagnostics

Menu Item Description

T raction Indicates the inputs and

outputs for driving the

machine.

Auxiliary Indicates the inputs and

outputs for engaging auxiliary

hydraulics.

Engine Indicates the inputs and

outputs for starting the engine.

Boom Indicates the inputs and

outputs for extending and

retracting the telescoping

arms.

Settings

Menu Item Description

Units

Controls the units used on the

InfoCenter; the menu choices

are Imperial or Metric.

Language

Controls the language used

on the InfoCenter .

Brightness

Controls the brightness of the

LCD display .

Contrast Controls the contrast of the

LCD display .

Protected Menus

Grants access to protected

menus.

Protect Settings Changes whether a pin is

required in Protected Menus.

About

Menu Item Description

Model

Lists the model number of the

machine

Serial Lists the serial number of the

machine

Software Lists the system software

revision of the machine.

Display

Lists the display software

revision of the InfoCenter .

Accessing Protected Menus

Note: The factory default PIN code for you machine

is either 0000 or 1234.

If you changed the PIN code and forgot the code,

contact your Authorized Service Dealer for assistance.

1. From the M AIN MENU , scroll down to the

SETTINGS MENU and press the right button.

g364600

Figure 16

17

2. In the S ETTINGS MENU , scroll down to the

PROTECTED MENU and press the right button.

g364601

Figure 17

3. T o enter the PIN code, press the center button

until the correct rst digit appears, then press

the right button to move on to the next digit.

Repeat this step until the last digit is entered and

press the right button once more.

g364599

Figure 18

4. Press the middle button to conrm the PIN code.

Note: If the InfoCenter accepts the PIN code

and the protected menu is unlocked, the word

“PIN” displays in the upper right corner of the

screen.

Y ou can view and change the settings in the

PROTECTED MENU . Once you access the P ROTECTED

MENU , scroll down to P ROTECT SETTINGS option.

Use the right button to change the setting. Setting

the Protect Settings to O FF allows you to view and

change the settings in the P ROTECTED MENU without

entering the PIN code. Setting the Protect Settings

to O Nhides the protected options and requires you

to enter the PIN code to change the setting in the

PROTECTED MENU .

Specications

Note: Specications and design are subject to

change without notice.

Width

1 16.8 cm (46.0 inches)

Length

215.6 cm (84.9 inches)

Height

143.5 cm (56.5 inches)

W eight

1750 kg (3858 lb)

Operating capacity (35% of tipping

capacity

1

)

589.7 kg (1300 lb)•Arms retracted

•Arms extended

280 kg (618 lb)

T ipping capacity

1

1685 kg (3714 lb)•Arms retracted

•Arms extended

792 kg (1746 lb)

Wheelbase

99.1 cm (39.0 inches)

Dump height (with standard bucket)

180.1 cm (70.9 inches)•Arms retracted

•Arms extended

230.3 cm (90.7 inches)

Reach—fully raised (with standard

bucket)

33.5 cm (13.2 inches)•Arms retracted

•Arms extended

67.8 cm (26.7 inches)

Height to hinge pin (with standard

bucket in highest position)

227.1 cm (89.4 inches)•Arms retracted

•Arms extended

277.3 cm (109.2

inches)

1 . T h e o p e r a t i n g c a p a c i t y i s c a l c u l a t e d a s 3 5 % o f t h e t i p p i n g c a p a c i t y w i t h

a s t a n d a r d b u c k e t a n d 7 5 k g ( 1 6 5 l b ) o p e r a t o r , p e r I S O 1 4 3 9 7 - 1 . O t h e r

a t t a c h m e n t s w i l l h a v e d i f f e r e n t o p e r a t i n g c a p a c i t i e s ; r e f e r t o t h e O p e r a t o r ’ s

M a n u a l o r l o a d c a p a c i t y d e c a l f o r t h e a t t a c h m e n t .

Attachments/Accessories

A selection of T oro-manufactured attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

T oro-manufactured attachments and accessories.

T o ensure optimum performance, use genuine T oro

replacement parts and accessories. T oro accepts

no liability for machine damage or personal injury

that results from the use of other manufacturer

attachments. The user accepts the burden of these

risks.

18

Operation

Note: Determine the left and right sides of the

machine from the normal operating position.

Before Operation

Before Operation Safety

General Safety

•Never allow children or untrained people to

operate or service the machine. Local regulations

may restrict the age or require certied training of

the operator . The owner is responsible for training

all operators and mechanics.

•Become familiar with the safe operation of the

equipment, operator controls, and safety decals.

•Always engage the parking brake (if equipped),

shut of f the engine, remove the key , wait for all

moving parts to stop, and allow the machine

to cool before adjusting, servicing, cleaning, or

storing the machine.

•Know how to stop the machine and shut of f the

engine quickly .

•Check that the safety switches, and shields are

attached and functioning properly . Do not operate

the machine unless they are functioning properly .

•Locate the pinch-point areas marked on the

machine and attachments; keep your hands and

feet away from these areas.

•Before operating the machine with an attachment,

ensure that the attachment is properly installed.

Read all the attachment manuals.

•Evaluate the terrain to determine what accessories

and attachments you need to properly and safely

perform the job.

•Have the property or work area marked for buried

lines and other objects, and do not dig in marked

areas; note the location of unmarked objects and

structures, such as underground storage tanks,

wells, and septic systems.

•Inspect the area where you will use the equipment

for uneven surfaces and hidden hazards.

•Ensure that the area is clear of bystanders before

operating the machine. Stop the machine if a

bystander enters the area.

Fuel Safety

•Use extreme care when handling fuel. It is

ammable and its vapors are explosive.

•Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

•Use only an approved fuel container .

•Do not remove the fuel cap or ll the fuel tank

while the engine is running or hot.

•Do not add or drain fuel in an enclosed space.

•Do not store the machine or fuel container where

there is an open ame, spark, or pilot light, such

as on a water heater or other appliance.

•If you spill fuel, do not attempt to start the engine;

avoid creating any source of ignition until the fuel

vapors have dissipated.

•T o prevent a static charge from igniting the fuel,

remove the machine from the truck or trailer and

refuel it on the ground, away from all vehicles. If

this is not possible, place a portable fuel container

on the ground, away from all vehicles, and ll it;

then refuel the machine from the fuel container

rather than from a fuel-dispenser nozzle.

•Keep the fuel-dispenser nozzle in contact with

the rim of the fuel tank or container opening at

all times until fueling is complete. Do not use a

nozzle lock-open device.

Adding Fuel

Recommended Fuel

Use only clean, fresh diesel fuel or biodiesel fuels

with ultra low (<15 ppm) sulfur content. The minimum

cetane rating should be 45. A cetane rating greater

than 50 is preferred, especially at temperatures below

-20°C (-4°F) or at elevations above 1500 m (5000 ft).

Purchase fuel in quantities that you can use within

180 days to ensure fuel freshness.

Using non-ultra low sulfur fuel will damage the engine

emissions system.

Use summer-grade diesel fuel (No. 2-D or No.

2-D S15) at temperatures above -10°C (14°F) and

winter grade (No. 1-D or No. 1-D S15) below

that temperature. Using winter-grade fuel at lower

temperatures provides lower ash point and cold ow

characteristics, which eases starting and reduces fuel

lter plugging.

Using summer-grade fuel above -10°C (14°F)

contributes toward longer fuel pump life and increased

power compared to winter-grade fuel.

Important: Do not use kerosene or gasoline

instead of diesel fuel. Failure to observe this

caution will damage the engine.

19

Biodiesel Ready

This machine can also use a biodiesel blended fuel

of up to B5 (5% biodiesel, 95% petrodiesel). The

petrodiesel portion should be low or ultra low sulfur .

Observe the following precautions:

•The biodiesel portion of the fuel must meet

specication ASTM D6751 or EN14214.

•The blended fuel composition should meet ASTM

D975 or EN590.

•Painted surfaces may be damaged by biodiesel

blends.

•Use B5 (biodiesel content of 5%) or lesser blends

in cold weather .

•Monitor seals, hoses, gaskets in contact with fuel

as they may degrade over time.

•Fuel lter plugging may occur for a time after

converting to biodiesel blends.

•Contact your distributor for more information on

biodiesel.

Filling the Fuel T ank

Fuel tank capacity: 43.5 L (1 1.5 US gallons)

1. Park the machine on a level surface, engage the

parking brake, and lower the loader arms.

2. Shut of f the engine and remove the key .

3. Raise the bracket.

g362590

Figure 19

1. Fuel cap

4. Remove the fuel cap.

5. Fill the tank with fuel up to the ller neck.

6. Install the cap.

7. Lower the bracket.

Performing Daily

Maintenance

Before starting the machine each day , perform the

Each Use/Daily procedures listed in the Maintenance

( page 40 ) .

Important: Check the hydraulic-uid level

and bleed the fuel system before starting the

engine for the rst time; refer to Checking the

Hydraulic-Fluid Level ( page 62 ) and Bleeding the

Fuel System ( page 50 ) .

During Operation

During Operation Safety

General Safety

•Do not exceed the rated operating capacity , as

the machine may become unstable, which may

result in loss of control. The operating capacity

is reduced if you extend the loader arms to the

point where you can see the striped decal inside

the arms.

•Do not transport an attachment/load with the

arms raised or extended; always transport the

attachments/load close to the ground, with the

loader arms retracted.

•Attachments can change the stability and the

operating characteristics of the machine.

•For machines with a platform:

– Lower the loader arms before stepping of f the

platform.

– Do not try to stabilize the machine by putting

your foot on the ground. If you lose control of

the machine, step of f the platform and away

from the machine.

– Do not place your feet under the platform.

– Do not move the machine unless you are

standing with both feet on the platform and

your hands are holding onto the reference bars

or the loader control.

•Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

•Look behind and down before backing up to

ensure that the path is clear .

•Never jerk the controls; use a steady motion.

•The owner/user can prevent and is responsible

for accidents that may cause personal injury or

property damage.

20

Page is loading ...

Toro Dingo TX 1300 Track Loader User manual

Toro Dingo TX 1300 Track Loader User manual

Related papers