AMP Lighting AFL-4010-B-BZ Installation guide

Brand
AMP Lighting
Model
AFL-4010-B-BZ
Type
Installation guide

This manual is also suitable for

AMP Lighting AFL-4010-B-BZ is a low voltage landscape lighting diffuse flood light, intended for installation in accordance with local codes and the National Electric Code (NEC).

This flood light is part of the AMP Lighting product line and is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. The main low voltage cable is intended for shallow burial - less than 6 inches (152 mm).

The flood light comes with the following package contents:

  • 1 stake
  • 1 luminaire

The product dimensions are as follows:

  • 4 inches in length
  • 2 inches in width

AMP Lighting AFL-4010-B-BZ is a low voltage landscape lighting diffuse flood light, intended for installation in accordance with local codes and the National Electric Code (NEC).

This flood light is part of the AMP Lighting product line and is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. The main low voltage cable is intended for shallow burial - less than 6 inches (152 mm).

The flood light comes with the following package contents:

  • 1 stake
  • 1 luminaire

The product dimensions are as follows:

  • 4 inches in length
  • 2 inches in width
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
DiffusePro Flood Light
AFL-4010-4-B-BZ
AMP
®
DiffusePro Flood Light
AFL-4010-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
Install Stake
A. (1) Stake
B. (1) Luminaire
4”
1.5”
2”
Determine the desired location for mounting
the luminaire. Hammer the stake into the
ground until the ange of stake is ush to
grade. To avoid damage to the stake, place a
board on top of stake while hammering.
NOTE: If the ground is hard and the stake is
difcult to install, make a crosscut in ground
using a at shovel.
Board
Stake
Soil
Ground
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP
®
DiffusePro Flood Light
AFL-4010-4-B-BZ
Remove Cover and Gasket with Lens
Install Bulb
Loosen the lock screws and remove the cover and gasket with the lens
from the luminaire to expose the socket.
Luminaire
Socket
Cover
Gasket with Lens
Lock Screw
Insert the bulb with correct
wattage and type marked on the
luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with
bare hands. Use soft cloth to
handle lamp.
Bulb
Socket
[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP
®
DiffusePro Flood Light
AFL-4010-4-B-BZ
Install Gasket with Lens and Cover
Install Luminaire to Stake
Decide which lens you would like to use with this xture. Then install
the gasket with your lens of choice back onto the luminaire and secure
with the lock screws.
Luminaire
Cover
Gasket with Lens
Lock Screw
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the luminaire pigtail
into the wireway slot and screw the
xture on to the stake. Tighten the
hex nut on the luminaire against the
stake and tighten until snug.
Luminaire
Hex Nut
Stake
Pigtail
Wireway Slot
INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
Install/Replace Bulb
AMP
®
DiffusePro Flood Light
AFL-4010-4-B-BZ
Wire Connections
Strip both leads from the luminaire pigtail. Using two wire connectors (sold
separately), connect the leads from the luminaire to the main supply cable
leads.
Pigtail
Main Supply Cable
Wire Connectors
Please reverse Step 2 - Step 4 to expose the bulb and replace it with correct
wattage and type marked on the luminaire label. Reinstall the gasket with
the lens and cover.
IMPORTANT: Halogen lamps must be protected from moisture and dust at all
times. Always reinstall gasket with lens and cover when removed.
–6––6–
[email protected] • 813.978.3900
–7–
IS-AFL-4010-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AMP Lighting AFL-4010-B-BZ Installation guide

Brand
AMP Lighting
Model
AFL-4010-B-BZ
Type
Installation guide
This manual is also suitable for

AMP Lighting AFL-4010-B-BZ is a low voltage landscape lighting diffuse flood light, intended for installation in accordance with local codes and the National Electric Code (NEC).

This flood light is part of the AMP Lighting product line and is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. The main low voltage cable is intended for shallow burial - less than 6 inches (152 mm).

The flood light comes with the following package contents:

  • 1 stake
  • 1 luminaire

The product dimensions are as follows:

  • 4 inches in length
  • 2 inches in width
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents