Powerplus POWXG6305 Owner's manual

Brand: Powerplus

Model: POWXG6305

Type: Owner's manual

Powerplus POWXG6305: Your robotic lawnmower for a perfectly cut lawn. Mow your lawn effortlessly and efficiently with this robotic lawnmower. It's ideal for gardens up to 500m² and features a range of smart functions for a precise and convenient mowing experience.

  POWXG6305  EN 
Copyright © 2020 VARO  P a g e    |  1  www.varo.com 
INTENDED USE ............................................................................... 3 
DESCRIPTION (FIG A, B & C) ........................................................ 3 
PACKAGE CONTENT LIST ............................................................. 3 
EXPLANATION OF USED SYMBOLS ............................................ 4 
SAFETY INSTRUCTIONS ................................................................ 4 
1  Training.................................................................................................................... 4 
2  Preparation .............................................................................................................. 4 
3  Operation ................................................................................................................. 5 
3.1  General ..................................................................................................................... 5 
3.2  Additionally when the machine is operating automatically ......................................... 5 
3.3  Maintenance and storage .......................................................................................... 5 
3.4  Recommendations .................................................................................................... 5 
SPECIAL SAFETY REGULATIONS FOR ROBOTIC 
LAWNMOWER ............................................................................................. 6 
1  Robotic lawnmower safety warning ....................................................................... 6 
2  Battery/Battery charger safety warnings ............................................................... 6 
OPERATION ..................................................................................... 7 
1  Lawn preparation .................................................................................................... 7 
2  Charging station placement and connection ........................................................ 7 
3  Charging the lawnmower ........................................................................................ 8 
4  Setting up the perimeter wire (Fig 3, Fig 4 and Fig 5) ........................................... 8 
5  Setting up the robotic lawnmower ....................................................................... 10 
5.1  Blade height adjusting knob (2) ............................................................................... 10 
5.2  Password ................................................................................................................ 10 
5.3  Start the mower ....................................................................................................... 10 
5.4  Set the work time and the work cycle ...................................................................... 11 
5.5  Stop the robotic mower ........................................................................................... 11 
5.6  Change password ................................................................................................... 12 
6  Control panel information (Fig 7) ......................................................................... 12 
6.1  Light status ............................................................................................................. 12 
6.2  Buttons ................................................................................................................... 13 

  POWXG6305  EN 
Copyright © 2020 VARO  P a g e    |  2  www.varo.com 
TROUBLE SHOOTING .................................................................. 13 
1  Fault codes ............................................................................................................ 13 
1.1  Fault codes (when outside charging station)............................................................ 13 
1.2  Fault codes (when charging) ................................................................................... 14 
1.3  Clear the fault code ................................................................................................. 14 
2  Mower does not work ........................................................................................... 15 
MAINTENANCE ............................................................................. 16 
1  General maintenance plan .................................................................................... 16 
2  Cleaning the mower .............................................................................................. 16 
3  Blade replacement (Fig 8) ..................................................................................... 17 
4  Storage .................................................................................................................. 17 
TECHNICAL DATA ........................................................................ 17 
NOISE ............................................................................................. 18 
WARRANTY ................................................................................... 18 
ENVIRONMENT ............................................................................. 19 
1  Battery pack .......................................................................................................... 19 
DECLARATION OF CONFORMITY .............................................. 20 
 

POWXG6305 EN

ROBOTIC LAWNMOWER 18V 2.5AH 500M²

POWXG6305

1 INTENDED USE

The robotic lawnmower is designed to mow grass ground areas where the slope is less than

17°. No collection of grass is required, and small particles of cut grass will reduce the need of

fertilizers. Before you can start mowing with your robotic lawnmower, you have to prepare the

lawn initially, find a proper place for your charging station and set up the perimeter wire to

define the borders of the mowing area.

WARNING! For your own safety, read this manual and the general safety

instructions carefully before using the appliance. Your power tool should

only be given to other users together with these instructions.

2 DESCRIPTION (FIG A, B & C)

1. Stop button

2. Blade height adjust knob

3. Control panel

4. Rain sensor

5. Handle

6. On/Off switch

7. Blades

8. Wheels

9. Caster wheels

10. Charging pins

11. Mounting holes

12. Charging indicator

13. Charging socket

14. Terminals for perimeter wire

15. Power adapter

16. Peg for charging station

17. Spare blades & screws

18. Wire connector

3 PACKAGE CONTENT LIST

▪ Remove all packing materials.

▪ Remove remaining packaging and transit supports (if existing).

▪ Check the completeness of the packing content.

▪ Check the appliance, the power cord, the power plug and all accessories for transportation

damages.

▪ Keep the packaging materials as long as possible till the end of the warranty period.

Dispose it into your local waste disposal system afterwards.

WARNING: Packing materials are no toys! Children must not play with

plastic bags! Danger of suffocation!

1 x robotic lawnmower

1 x charging station

1 x power adapter

4 x peg for charging station

6 x spare blades & screws

1 x wire connector

160 x installation peg

120m perimeter wire

1 x manual

When parts are missing or damaged, please contact your dealer.

POWXG6305 EN

4 EXPLANATION OF USED SYMBOLS

Read manual before use.

Always keep a safe

distance from the machine

when operating.

Never use the machine

when persons, children or

pets are in the cutting area.

Always remove the disabling

device（On/Off switch） before

working on or lifting the

machine.

Do not sit or ride on the

machine.

The product complies with the

applicable European directives

and an evaluation method of

conformity for these directives

was done.

At the end of its lifecycle,

the device must not be

disposed of with normal

household waste. Ensure

that the device is disposed

of in accordance with local

regulations.

Li-ion battery. This product has

been marked with a symbol

relating to ‘separate collection’

for all battery packs. It will then

be recycled or dismantled in

order to reduce the impact on

the environment.

Guaranteed sound power

level.

5 SAFETY INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE USE! KEEP FOR FUTURE

REFERENCE!

5.1 Training

▪ Read the instructions carefully. Be familiar with the controls and the proper use of the

machine.

▪ Never allow people unfamiliar with these instructions or children to use the machine. Local

▪ regulations may restrict the age of the operator.

▪ The operator or user is responsible for accidents or hazards occurring to other people or

their property.

▪ Never allow children, persons with reduced physical, sensory or mental capabilities or lack

of experience and knowledge or people unfamiliar with these instructions to use the

machine, local regulations may restrict the age of the operator.

5.2 Preparation

▪ Ensure the correct installation of the charging station and boundary wire as instructed.

POWXG6305 EN

▪ Periodically inspect the area where the machine is to be used and remove all stones,

sticks, wires, bones, and other foreign objects. Failure to do so can lead to the mower

getting stuck / damaged!

▪ Periodically visually inspect to see that the blades, blade bolts and cutter assembly are not

worn or damaged. Replace worn or damaged blades and bolts in sets to preserve

balance.

▪ On multi-spindle machines, take care as rotating one blade can cause other blades to

rotate.

5.3 Operation

5.3.1 General

▪ Never operate the machine with defective guards, or without safety devices.

▪ Do not put hands or feet near or under rotating parts.

▪ Never pick up or carry an machine while the motor is running.

▪ Remove (or Operate) the disabling device from the machine

o before clearing a blockage;

o before checking, cleaning or working on the machine;

o after striking a foreign object to inspect the machine for damage;

o if the machine starts to vibrate abnormally, and to check for damage

before restarting.

5.3.2 Additionally when the machine is operating automatically

▪ Do not leave the machine to operate unattended if you know that there are pets, children

or people in the vicinity.

5.3.3 Maintenance and storage

▪ Keep all nuts, bolts, and screws tight to be sure the machine is in safe working condition.

▪ Replace worn or damaged parts for safety.

▪ Ensure that only replacement cutting means of the right type are used.

▪ Ensure that batteries are charged using the correct charger recommended by the

manufacturer. Incorrect use may result in electric shock, overheating or leakage of

corrosive liquid from the battery.

▪ In the event of leakage of electrolyte flush with water/neutralizing agent, seek medical help

if it comes into contact with the eyes, etc.

▪ Servicing of the machine should be according to manufacturers’ instructions.

5.3.4 Recommendations

▪ Connect the machine and/or its peripherals only to a supply circuit protected by a residual

current device (RCD) with a tripping current of not more than 30 mA.

▪ Avoid using the machine and its peripherals in bad weather conditions especially when

there is a risk of lightning.

▪ Read all safety warnings and all instructions. Failure to follow all warnings and instructions

may result in electric shock, fire and/or serious injury. Save all warnings and instructions

for future reference. The term "power tool" in the warnings refers to your mains operated

(corded) power tool or battery operated (cordless) power tool.

POWXG6305 EN

6 SPECIAL SAFETY REGULATIONS FOR ROBOTIC LAWNMOWER

6.1 Robotic lawnmower safety warning

▪ Never allow people unfamiliar with these instructions or children to use the machine.

▪ The use of the appliance by persons (including children) who have limited physical,

sensory or mental abilities or lack the necessary experience and knowledge is prohibited

unless they have been supervised at work by a person responsible for their safety and

have received prior training in the use of the appliance. Do not allow children to play with

the appliance. The appliance is not a toy.

▪ Wear long pants and sturdy shoes when nearby or inside the work area while the lawn

mower is operating.

▪ Do not ride on the lawn mower, push the lawn mower, or use it for anything other than its

intended purpose, otherwise you or someone else may be injured.

▪ Do not use automatic lawn watering systems while the lawn mower is operating, because

the watering equipment may become damaged and the likelihood of water penetrating into

the lawn mower is greatly increased. Adjust the work time of the lawn mower so that the

watering systems and the lawn mower do not operate at the same time.

▪ Ensure the correct installation of the charging station and boundary wire as instructed in

this manual.

▪ Periodically inspect the area where the machine is to be used and remove all stones,

sticks, wires, branches and other foreign objects.

WARNING: The machine can be dangerous if used improperly.

WARNING: When carrying the lawn mower, make sure to carry it by the

designed areas. If you carrying the lawn mower in any other way, you risk

injury from the blades or charging socket of the lawn mower.

6.2 Battery/Battery charger safety warnings

▪ Protect the battery charger from rain and moisture. The penetration of water in a battery

charger increases the risk of electric shock.

▪ Recharge only with the charger specified by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of fire when used with another battery pack.

▪ Do not charge other batteries. The battery charger is suitable only for charging lithium ion

batteries of POWXG6305. Otherwise danger, fire and explosion may occur.

▪ Keep the battery charger clean. Contamination may cause the danger of electric shock.

▪ Check the battery charger, cable and plug each time before using. Do not use the battery

charger when defects are detected. Do not open the battery charger yourself and have it

repaired only by qualified personnel using original spare parts. Damaged battery chargers,

cables and plugs increase the risk of electric shock.

▪ Do not operate the battery charger on easily inflammable surfaces (e. g. paper, textiles,

etc.) or in combustible environments. There is danger of fire due to the heating of the

battery charger during charging.

▪ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irritation or burns.

▪ Do not open the battery yourself. There is danger of a short circuit.

▪ Protect the battery against heat, e.g., including against continuous sun irradiation and fire.

There is a danger of explosion.

▪ Do not short-circuit the battery. There is a danger of explosion.

POWXG6305 EN

▪ In case of damage and improper use of the battery, vapours may be emitted. In case of

complaints, provide for fresh air and consult a physician. The vapours can irritate the

respiratory system.

7 OPERATION

7.1 Lawn preparation

Before operating the robotic lawnmower, ensure that the mowing area is free of pets, kids or

objects. Remove stones, loose pieces of wood, wire, cables from the lawn. Make sure that the

lawn height is 50 mm or less. If the height is more than that, cut the lawn to a height of 50

using a standard lawnmower. Cut the area where you intend to lay the perimeter wire to the

lowest setting you have with your conventional mower.

7.2 Charging station placement and connection

Find the best place for your charging station (if possible out of the sun), where your robotic

lawnmower will return to get charged.

1. Take the robotic lawnmower from the charging station and place the charging

station on level ground outside the mowing area.

Make sure

• that you have a straight 1.5 m track in front of the charging station.

• that the base stand is firmly on the ground and does not bend.

• not to put the charging station in confined spaces.

• that you have 1.0 m of free space perpendicular to the rear the charging

station.

• that the next power socket is within 6 meters.

• that the charging station is not placed in direct sunlight, if possible.

It is recommended to place the charging as close to the power supply as possible. The total

length of the power cable is 6 m.

Note: Your robotic lawnmower can only automatically return to the charging

station counter-clockwise.

Note: When your robotic lawnmower receives direct sunlight for a

prolonged period of time the battery can get too hot and will not function

correctly.

2. Fix the charging station with the four supplied pegs.

3. Connect the charging socket to the charging adaptor.

4. Connect the charging adaptor to the power supply (Fig 1).

Make sure that the power supply is

• close to the charging station

• protected from rain, e.g. under a roof

• protected from direct sunlight, if possible

➔ Once connected you should now see a red light (power) on the charging

station.

➔ The green light (work) on the charging station indicates wiring conditions of the

charging station. When the green light flashes, the wire is not set correctly and

the mower cannot work.

Note: When mower is charging the green light on charging station will also

flash. If mower is not in charging station and green light on charging station

POWXG6305 EN

flashes this will indicate that wire is not set correctly, and then mower will not

work.

7.3 Charging the lawnmower

Your robotic lawnmower´s battery may be charged to a certain degree on delivery, but it´s

recommended to fully charge the battery of the lawnmower before use. To charge your robotic

lawnmower follow these steps:

1. Switch the robotic lawnmower on. The On/Off switch (6) is located at the bottom

side of the robotic lawnmower (FIG A and Fig 2).

Note: Your robotic lawnmower will not charge when it is not turned on.

Note: The robotic lawnmower will enter a self-checking state (normally within

5 seconds) after entering the password or when the power is interrupted

during mowing or charging (indicated by a flashing status light). If the mower

is in a self-check state, you will not hear a sound when pressing a button and

the buttons won´t work.

2. Slide the robotic lawnmower into the charging station to charge.

3. Check the indicator on the charging station. The red power light turns up and the

robotic lawnmower charges (green light flashes). If the power light does not light up,

you should check the mains plug of the power supply is plugged in properly and that

the mower is in the station correctly.

4. When mower is charging the status light on the robot mower control panel will flash

quickly (4 times a second), when mower is fully charged the status light will flash

slowly (every 2 seconds).

5. It takes about 90 minutes to get the battery fully loaded.

7.4 Setting up the perimeter wire (Fig 3, Fig 4 and Fig 5)

The wire defines the borders of the mowing area. Everything in the inner area belongs to the

mowing area, everything in the outer area doesn´t belong to the mowing area. The wire also

serves to mark obstacles and exclude them from the mowing area.

1. Feed the end of the perimeter wire through the groove on the front at the bottom

side of the charging station, until it appears on the rear side (Fig 3).

2. Carefully strip off 10-15 mm of the insulation of the wire.

Note: You should keep a length of 15-20 cm at start and the end of the wire for

operating and handling the wire.

3. Connect the wire to the right hand (black) B terminal of the charging station (Fig 4).

4. Start installing the perimeter wire from the charging station in a clockwise direction

(Fig 5). Pull the wire from the coil, tauten and fix it with one peg. Use a mallet to

insert them in the lawn. Ensure the wire is straight and in line with the charging

station groove for 1.5 m.

5. Recommended distance between pegs is 50 to 75 cm (max).

6. Continue to set the wire around the perimeter of the mowing area. For a more

accurate perimeter, we advise that you leave less than 75 cm between pegs when

wiring objects (like flower beds, bushes, trees and other items).

Loose wire can be cut during mowing. Make sure the wire is flat to the ground.

Use additional pegs where the wire is slack. The wire is taut before placing the

POWXG6305 EN

next peg (if you can place a couple of fingers under the wire this is not taut

enough). Increase the number of pegs at a corner.

Note: If the mowing area borders against a flat path or a surface that is level

with the lawn, your robotic lawnmower will be able to run over it. In such

cases the perimeter wire should be positioned right up to the edge of the lawn

(approx. 10 cm). This is not applicable for gravel, as your robotic lawnmower

could hit a stone or get stuck in the gravel.

Note: When installing the wire around the perimeter of pond of water, the

distance between the wire and the edge of the pond must be more than 75 cm,

because of safety reasons. In case there is a power cut your robotic

lawnmower will stop after not noticing the wire for 50 cm.

Note: When marking objects remember there must be at least 75 cm distance

between two objects. Leaving less distance than this will cause some

interference.

Note: Do not install the wire on the slope (max 17° or 30%), or your mower

could be slip out the boundary easily.

Note: The robotic lawnmower cannot go through distance less than 60cm.

7. Encircling obstacles (Fig 5). Mark out permanent objects you do not want the mower

to run over, e.g. roots, ponds, flower beds or rocks. This will prevent your robotic

lawnmower colliding with objects or going straight into them.

To mark a obstacle:

a. Run the wire from the lawn perimeter to the object.

b. Continue round the objects in a clockwise direction. When going around

the object use more pegs. So they are closer than 75 cm.

c. Return the wire back to the perimeter. Ensure the distance from the wire

around the object and lawn perimeter wire is at least 75 cm.

Please ensure that the two parallel wires leading to and from the marked object are

as close as possible by placing the wire under the same side of the peg. This will

make the wire undetectable to your robotic lawnmower. Please ensure that the

wires do not cross over each other at any point..

Note: Remember to leave 30 cm around the object to the wire! If objects are

less than 75 cm from the lawn edge, surround the object when installing the

wire, leaving the object outside of the lawn cutting area.

8. When the perimeter wire has been laid around the entire cutting area, cut the wire

and strip 10-15 mm of insulation off.

9. Connect the wire to the left hand (red) terminal (Fig 4).

Note: Observe the distances in Fig 6 if a second mower is used next or on the

property.

POWXG6305 EN

7.5 Setting up the robotic lawnmower

When your robotic lawnmower´s battery is fully loaded, you can start setting up the

lawnmower.

7.5.1 Blade height adjusting knob (2)

First you have to set up the cutting height. Turn the knob to adjust the blades to a appropriate

cutting height. They can be adjusted between 25 mm-50 mm manually.

7.5.2 Password

The robotic lawnmower is password protected. To start the lawnmower for the first time, you

have to enter the password (the 2D, 2H, 4H and 6H light flashes). This needs to be done when

the mower is OUTSIDE the charging station, when the mower is at the charging station you

cannot enter the password for the first time. Factory default password is 1111. You can enter

the password by the panel on the top side of the mower.

See Fig 7, panel on the top side, status light marked with a red rectangle.

1. Press CYCLE (for password number “1”). The 2D light is off.

2. Press CYCLE (for password number “1”) a second time. The 2H light is off.

3. Press CYCLE (for password number “1”) a third time. The 4H light is off.

4. Press CYCLE (for password number “1”) a fourth time. The 6H light is off.

Note: When no password is entered, the system is in a password protected

state, and the machine cannot be operated through the panel. The machine

can be charged. In this state, the state lamp (1D, 2D, 2H, 4H, 6H) are off and

the machine cannot cut grass automatically.

7.5.3 Start the mower

Note: The mower will only work when there is no water on the rain sensor (4).

If the mower is at the charging station:

Manual start

1. Press START + SET

2. Enter password

➔ The mower starts immediately when charged.

Pre-programmed start

1. Press START + CYCLE

2. Enter password

The mower will each time start at the same time after pressing START + CYCLE.

➔ The mower starts when the battery level is enough for the requirement of

working time.

If the mower is outside the charging station:

1. Enter password

2. Press START + SET or START + CYCLE

➔ The mower will start mowing if the battery level is high enough.

Note: The default setting is 1 day work cycle and 2 hours work time per day.

POWXG6305 EN

You can operate the mower with or without the change of the automatic starting time by the

following combinations:

Button

Action

Function

START + CYCLE

The mower works

Starts according to the originally set

working time, independent of the starting

time of the mower

START + SET

The mower works

Starts according to the starting time of the

mower

HOME + CYCLE

The mower will come

back to the charging

station

According to the originally set working time

after charging

HOME + SET

The mower will come

back to the charging

station

According to the starting time after

charging

Working time: 6 hours

per day

When entering the password: represents

the fourth digit of the password, if the

fourth digit is entered, the light is off

7.5.4 Set the work time and the work cycle

You can set how long the robotic mower works per day. You can choose between 2h, 4h or 6h

per day. To set the working time for the first time the mower needs to be outside the charging

station:

1. Press SET

2. Choose the working time by pressing SET repeatedly. The corresponding light (2H,

4H or 6H) is on.

➔ The working time counts from the start of the mower and includes the charging

time. For example: If you start the mower with the setting 2h, it will work for two

hours from the start. If you start the mower with the setting 6h, it works six

hours from the start.

3. Press CYCLE to set a working cycle time of one day or two days (indicated by the

1D and the 2D light).

➔ The mower will work every day for the set time (1D) or the mower will work

every other day for the set time (2D).

Note: The working time includes the charging time.

7.5.5 Stop the robotic mower

You can always stop your robotic mower by pressing the STOP button (1) on the top.

The robotic mower will stop immediately.

Note: The stop button has the highest priority, the robotic lawnmower will

stop running in any case.

To restart the mower after pressing the STOP button:

1. Make sure that all conditions for starting the mower are met (for the mower itself and

in the mowing area).

2. Enter the password.

3. Press CYCLE, then START and then HOME to leave emergency stop state.

4. Press START and then CYCLE to restart the mower, or press HOME and then

CYCLE to send mower back to the charging station.

POWXG6305 EN

7.5.6 Change password

You can change the password from default (“1111”) to your own combination of 4 numbers.

The password combination consists 4 digits from 1 to 4. Note: for this procedure the mower

must be outside the charging station. If the mower has already mowed, switch off the mower

and switch it on again after +/- 30 sec, then carry out the following actions:

1. Enter original password.

2. Press SET and CYCLE at the same time.

3. Enter a new password (status light is on) that consists of four numbers.

For example if you want to change the password to “4231”:

Press “SET” button to insert digit 4

Press “HOME” button to insert digit 2

Press “START” button to insert digit 3

Press “CYCLE” button to insert digit 1

4. Enter the new password a second time. The status light is on continuously and the

LEDs for mowing times 1D or 2D and 2h / 4h / 6h are on continuously.

➔ If two passwords are equal, the change is successful. Otherwise, the status

light flashes (change failed).

7.6 Control panel information (Fig 7)

7.6.1 Light status

Light

1st function

2nd function

Status light

Shows fault code in

case of a problem

When changing the password: indicates

the first time to enter the password

Recurring work cycle: 1

day

When changing the password: indicates

the second time to enter the password

Recurring work cycle: 2

days

When entering the password: represents

the first digit of the password, if the first

digit is entered, the light is off

Working time: 2 hours

per day

When entering the password: represents

the second digit of the password, if the

second digit is entered, the light is off

Working time: 4 hours

per day

When entering the password: represents

the third digit of the password, if the third

digit is entered, the light is off

Working time: 6 hours

per day

When entering the password: represents

the fourth digit of the password, if the

fourth digit is entered, the light is off

POWXG6305 EN

7.6.2 Buttons

Button

1st function

2nd function

Cycle

Set the recurring work

cycle

- When entering the password: number

one (1)

- When setting the password protection

time: extend time. When the system

fault indicator flashes, press this

button to delay the system password

protection.

- When a problem with a fault code

occurs: show fault code. Use 1 minute

to facilitate the observation of the

cause of the fault (when not pressed,

the system password protection is

activated after 20 seconds)

Home

Send the mower to the

charging station

When entering the password: number two

(2)

Start

Start the robotic mower

When entering the password: number

three (3)

Set

Set the working time per

day

When entering the password: number four

(4)

8 TROUBLE SHOOTING

8.1 Fault codes

The robotic mower displays a fault code when unexpected events occurs. You can check the

fault code to find out the problem. See the list of fault codes below.

If you are not sure how many times the status light flashes, press the CYCLE button again to

observe the fault code again. The STATUS light is the red framed light Fig 7.

8.1.1 Fault codes (when outside charging station)

Status light flashing

Machine status

1 time

The emergency stop button is triggered

2 times

Self check status. (in this state, the button does not respond, just

wait until the self-check status is completed before operating.)

3 times

Excessive inclination or overturning causes the mowing to end

4 times

No enclosing signal was detected, which causes the mowing to

end (check whether the wire is installed correctly and connected)

5 times

The mower is not in the working area, this causes the mowing to

end (check whether the wire is installed correctly and connected)

6 times

The lift sensor is triggered causes the mowing to end

7 times

Low battery causes the mowing to end

8 times

High temperature causes the mowing to end

9 times

Abnormal clogging of the mowing motor causes the mowing to

end

10 times

Alternative brake abnormally causes the mowing to end

POWXG6305 EN

11 times

Boundary sensor failure causes the mowing to end

12 times

Main brake failure caused the mowing to end

13 times

Over-temperature of the mowing motor causes the mowing to

end

14 times

Rain caused the mower come back to charging station

15 times

Driving motor operates abnormally

16 times

Abnormal current of mowing motor

17 times

Left driving motor operates abnormally

18 times

Right driving motor operates abnormally

19 times

Two times change password is inconsistent

20 times

Not work during issue such as slip or can not go through the

area

8.1.2 Fault codes (when charging)

Status light flashing

Machine status

Continuous block flash

quickly (four times a

second)

The mower is charging

Continuous slow flash

(every two seconds)

The mower is completely charged

1 time

Over charging temperature protection

2 times

Abnormal charger protection, charging voltage is too high

3 times

Abnormal charger protection, charging current is too high

4 times

Abnormal battery protection, battery voltage is too low (no

charging below 10V)

5 times

BMS (Battery Management System) protection, no charging

allowed

The light is off

The mower does not turn on or is in low voltage protection state

(the voltage is lower than 16V, the mower should be restarted)

8.1.3 Clear the fault code

To clear the fault code follow these steps:

1. Make sure that all conditions for restarting the mower are met (for the mower itself

and in the mowing area).

2. Enter the Password.

3. The mower will enter a self-checking state (normally within 5 seconds) after entering

password without responding to the button operation.

4. Press CYCLE and any other of the three buttons to clear the fault code.

5. Press START and then CYCLE to restart the mower.

POWXG6305 EN

8.2 Mower does not work

Problem

Cause

Action

The mower stops during

mowing

a) Battery low

b) Abnormal state due to

unexpected

interrupting. Password

needed.

a) Re-charge the mower.

b) Enter the password.

Only status light flashes

with all other LEDs

keeping off in recurring

cycles during charging

Automatic setting is invalid

Re-enter a password.

The mower needs

password while charging

Charging is interrupted

Enter password and check the

reason:

- If the mower is not connected

to the charging station,

reconnect.

- If the power supply of the

charging station is not

connect correctly, reconnect it

After entering the

password, the mower

does not start

The START button is not

pressed or pressed to late

(more than 10 seconds after

the last digit of the

password).

Enter the password again.

The password change

does not work

a) Changing of password

failed due to wrong

password.

b) Changing of password

was too slow (more

than 20 seconds).

Repeat the password change

procedure.

The power of the mower

is cut off automatically

due to low battery

a) After restarting the

mower by the On / Off

switch, the power light

flashes.

b) After restarting the

mower by the On / Off

switch, the power light

does not flash.

a) Charge the mower in the

charging station within 5

seconds.

b) Charge the mower in the

charging station after

unplugging the perimeter

wire.

POWXG6305 EN

9 MAINTENANCE

Note: To ensure long and reliable service, carry out the following

maintenance regularly.

WARNING: Be aware of the danger of moving hazardous parts.

WARNING: Do not touch moving hazardous parts. Make sure the power

switch is set to OFF and make sure that all moving parts have come to a

stop before doing any maintenance on the mower.

9.1 General maintenance plan

Item

Action

Once a

week

Once a year / every 500

hours

Blades

Inspect

Blade plate

Inspect

STOP button

Inspect

Chassis accessories

Clear

Inspect

X (twice a year)

Charging station

Clear

Inspect

Charging station base

Inspect / Adjust

Driving wheel

Clear

Inspect

X (twice a year)

Omnidirectional wheels

Clear

Inspect

X (twice a year)

9.2 Cleaning the mower

ATTENTION! The power switch must be set to OFF before cleaning the

mower!

Wear thick gloves before turning the mower and while cleaning. The blades are sharp!

Do not use high pressure cleaners!

1. Set the On / Off switch of the mower to OFF.

2. Clear the blades and the blade plate with a brush. Remove all dirt and check

whether the blades can move free. Check this every two weeks.

3. Clean the surface of the mower with a piece of cloth. Don´t use any dissolvent.

POWXG6305 EN

9.3 Blade replacement (Fig 8)

ATTENTION! When fitting new blades, make sure you replace ALL the

blades. Always use new screws when fitting blades. This is important to

ensure blade retention. Failure to use screws could cause serious injury.

ATTENTION! Wear gloves when handling the blade. Only use original

replacement parts specified for this mower. Powerplus spare blades and

screws item reference number: POWACG9101.

It’s recommended that replace the blades within 2-3 months.

There are 3 blades on the robotic lawnmower, which are screwed into the blade disc. All 3

blades and screws must be replaced at the same time to obtain a balanced cutting system.

1. Set the on/off switch of the mower to "OFF".

2. Turn the robotic lawnmower upside down. Place the robotic lawnmower on a soft

and clean surface to avoid scratching the body and the cover.

3. Rotate the blade plate so that its holes align with the screws for the blade.

4. Remove the 3 screws with a screwdriver.

5. Remove each blade and screw.

6. Fasten new blades and screws.

7. Check that the blades can pivot freely.

9.4 Storage

Keep your mower and the charging station in a warm and dry place during winter.

1. Fully charge the battery.

2. Set the On / Off switch of the mower to OFF.

3. Clean the mower.

4. Disconnect the charging station from the power supply.

5. Disconnect the wire from the charging station.

6. Lift the charging station from the ground and clean it.

7. Store the mower and the charging station in a dry place.

10 TECHNICAL DATA

Type

POWXG6305

Mains voltage (charger unit)

220-240 V / 50 Hz

No load speed

3200 min

-1

Running time

70 min

Battery type

Li-Ion

Battery voltage

18 V

Battery capacity

2.5 Ah

Charging time (empty battery)

90 min

Motor type

Brushless

Max. area

500 m2

Cutting width

18 cm

Max slope

30% （17°)

Boundary wire(max.)

120 m

Charging current

2 A

Weight with 2.5 Ah battery

7.5 kg

POWXG6305 EN

11 NOISE

The declared vibration total value has been measured in accordance with a standard test

method and may be used for comparing one tool with another.

The declared vibration total value may also be used in a preliminary assessment of exposure.

The vibration emission during actual use of power tool can differ from the

declared total value depending on the ways in which the tool is used.

The safety measures to protect the operator are identified based on an

estimation of exposure in the actual conditions of use.

A-weighted emission sound pressure level at the operator position as determined according to

the relevant standard, where this level does not exceed 70 dB(A):

Acoustic pressure level LpA

48 dB(A)

Acoustic power level LwA

59 dB(A)

If there is any abnormal vibration please inspect your mower for any abnormal blockage. If

necessary clean the mower and/or replace the blades.

12 WARRANTY

This product is warranted for a 36-month period effective from the date of purchase by the first

user.

This warranty covers all material or production flaws excluding : batteries, chargers, defective

parts subject to normal wear & tear such as bearings, brushes, cables, and plugs, or

accessories such as drills, drill bits, saw blades, etc. ; damage or defects resulting from

maltreatment, accidents or alterations; nor the cost of transportation.

Damage and/or defects resulting from inappropriate use also do not fall under the warranty

provisions.

We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool.

Repairs may only be carried out by an authorized customer service centre for Powerplus tools.

You can always obtain more information at the number 00 32 3 292 92 90.

Any transportation costs shall always be borne by the customer, unless agreed otherwise in

writing.

At the same time, no claim can be made on the warranty if the damage of the device is the

result of negligent maintenance or overload.

Definitely excluded from the warranty is damage resulting from fluid permeation, excessive

dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate

usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not

following the instructions given in the manual), inexpert assembly, lightning strike, erroneous

net voltage. This list is not exhaustive.

Acceptance of claims under warranty can never lead to the prolongation of the warranty period

nor commencement of a new warranty period in case of a device replacement.

Devices or parts which are replaced under the warranty therefore remain the property of Varo

NV.

We reserve the right to reject a claim whenever the purchase cannot be verified or when it is

clear that the product has not been properly maintained. (Clean ventilation slots, carbon

brushes serviced regularly, etc.).

Your purchase receipt must be kept as proof of date of purchase.

Your appliance must be returned undismantled to your dealer in an acceptably clean state, (in

its original blow-molded case if applicable to the unit), accompanied by proof of purchase.

Your tool must be charged at least 1x per month to ensure optimal operation of this tool.

POWXG6305 EN

13 ENVIRONMENT

Should your appliance need replacement after extended use, do not discard it

with the household rubbish but dispose of it in an environmentally safe way.

Waste produced by electrical machine items should not be handled like normal

household rubbish. Please recycle where recycle facilities exist. Check with your

Local Authority or retailer for recycling advice.

13.1 Battery pack

This product contains Li-ion. To preserve natural resources, please recycle or dispose of

batteries properly. Local, state or federal laws may prohibit disposal of Li-ion batteries in

ordinary trash. Consult your local waste authority for information regarding available recycling

and/or disposal options.

POWXG6305 EN

14 DECLARATION OF CONFORMITY

VARO – Vic. Van Rompuy N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM,

declares that,

Product: Robot mower 18 V

trade mark: PowerPlus

model: POWXG6305

is in conformity with the essential requirements and other relevant provisions of the applicable

European Directives, based on the application of European harmonized standards. Any

unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of signature):

2011/65/EU

2006/42/EC

2014/30/EU

2000/14/EC Annex VI LwA

Measured 60dB(A)

Guaranteed 62dB(A)

Notified Body ISET - Italy)

European harmonized standards (including, if applicable, their amendments up to the date of

signature):

EN60335-1 : 2012

EN50636-2-107 : 2015

EN55014-1 : 2017

EN55014-2 : 2015

Keeper of the Technical Documentation: Philippe Vankerkhove, VARO – Vic. Van Rompuy

N.V.

The undersigned acts on behalf of the company CEO,

Philippe Vankerkhove

Regulatory Affairs – Compliance Manager

20/01/2021, Lier - Belgium

Powerplus POWXG6305 Owner's manual

Powerplus POWXG6305 Owner's manual

Powerplus POWXG6305 Owner's manual

Related papers

Other documents