Marshall Electronics BD-0914 User manual

Brand: Marshall Electronics

Model: BD-0914

Category: Video line amplifiers

Type: User manual

This manual is also suitable for

BD-0914-D

Marshall Electronics BD-0914 is a cost-effective solution for distributing HDSDI or SDI signals in various applications. It features a self-terminating 75Ω BNC SDI input with adaptive equalization and four buffered and reclocked BNC HDSDI or SDI outputs. The device supports signal formats from 143Mb/s to 1.5Gb/s and automatically selects the appropriate format. With a power indicator on the front panel and all connections at the rear, the BD-0914 can be installed in a rack, wall-mounted, or used on a desktop.

Marshall Electronics

Product Overview

Features

Mechanical Specifications

Optional Accessories

 Use for distribution of HDSDI or SDI signals 143Mb/s to 1.5Gb/s

 Self terminating 75

Ω BNC SDI input with adaptive equalization

 4 buffered and reclocked BNC HDSDI or SDI Outputs

 Power indicator on front panel

 All connections in rear of module

 Install in rack, wall mount or use on the desktop

 Can also be used as a signal repeater

Our BD-0914-D Serial Digital Distribution Amplifier is a cost effective solution for any application requiring

distribution of HDSDI or SDI signals.

V-CB1 Desktop Stand

V-CRM-2

2U (1.75” tall) Conversion and Distribution 3 Module Bracket.

Up to three Marshall Electronics 4.75” wide conversion or distribution

modules can be securely installed into a standard EIA 19 inch rack with

the V-CRM-3 mounting bracket. Every V-CRM-3 includes two blank pan-

els for a clean cosmetic appearance.

V-CRM-3

Single RU (1.75” tall) Conversion and Distribution 2 Module Bracket.

Two Marshall Electronics 7.72” wide or one 7.72” plus one 4.75” wide

conversion or distribution modules can be securely installed into a

standard EIA 19 inch rack with the V-CRM-2 mounting bracket. Every

V-CRM-3 includes one blank panel and one 4.75” adapter for a clean

cosmetic appearance.

BD-0914 Distribution Amplifier Users Guide

Signal Input BNC SDI (SMPTE-259M/292M/296/344M) (143Mb/s to 1.5Gb/s)

Signal Output 4 BNC Re-clocked SDI-Transmit speed 143Mb/s to 1.5Gb/s

Transmit speed is determined by speed of input signal

Return loss >15db (5Mhz to 2Ghz)

Signal Formats Automatic selection of Serial Digital formats 143Mb 1.5Gb

Input Cable Equalization 1150ft (350m) for 270Mb/s using Belden 1694A or Equivalent 450ft (140m) for

1.5Gb/s using Belden 1694A or Equivalent

Power required 6V D.C. supplied from external supply (Model V-PS6-1.2A is included)

Dimensions 4.75”W x 3.75”D x 1.0”H

BD-0914 Weight 0.55 lbs (0.25kg)

V-PS6-1.2A Power Supply Weight 0.20 lbs (0.10kg)

Electrical Specifications

1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • www.LCDRacks.com • Email: [email protected]om

Power On/Off System indicator.

Illuminates Red when Power applied from

V-PS6-1.2 Power supply

1. Unpack the BD-0914, and accompanying V-PS6-1.2A power supply and physically inspect for any damage that may have occurred

during shipping. Also verify there is a small package with mounting accessories. Should there be any damage, immediately contact

Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2. Install in your desired location. If wall mounting is required, attach the mounting brackets by removing the Phillips head screws on

the sides, closest to the rear of the unit. (See below) Only one screw per side should be removed. Use the same screw to attach the

bracket with the flange facing away from the side and parallel to the front of the BD-0914 metal case. The flange has two holes. For

desktop use, apply the supplied rubber pads.

3. Connect required cables for signal input and output.

Plug the power supply into the A.C. source

4. Attach power connection to the back of the unit to

turn on power. Verify power on indicator active on

the front of the BD-0914.

Operational Setup

1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • www.LCDRacks.com • Email: [email protected]om

BD-0914 Distribution Amplifier Users Guide

Output 1 to 4 BNC,

If HDSDI is input signal, output will be HDSDI

If SDI is input signal, output will be SDI

6 VDC from

V-PS6-1.2A power supply

Left Pin - Pos

Right Pin- Neg

HDSDI or SDI Input BNC

Warranty

Marshall Electronics warranties to the ﬁ rst consumer, that this BD-0914 HDSDI or SDI Signal Distribution Ampliﬁ er will, under normal use, be free from

defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.

This warranty is extended to the ﬁ rst consumer only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided

with a warranty claim, Marshall Electronics reserves the right, not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.

This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modiﬁ cations in design or

construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described

above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.

Due to constant effort to improve products and product features, speciﬁ cations may change without notice.

Input Connectors