Trendnet RB-TEW-692GR Owner's manual

Brand: Trendnet

Model: RB-TEW-692GR

Category: Networking

Type: Owner's manual

This manual is also suitable for

TEW-692GR

Trendnet RB-TEW-692GR is a wireless router that provides high-speed wireless connectivity for home and small office networks. It supports both 2.4GHz and 5GHz frequencies, allowing you to connect multiple devices simultaneously without experiencing lag or interference. With its four Gigabit Ethernet ports, you can connect wired devices such as gaming consoles, printers, and smart TVs for a fast and reliable wired connection.

Page is loading ...

Table of Contents

Version 05.05.2011

Deutsch 1

Troubleshooting 10

Wireless Tips

1. Bevor Sie anfangen 1

2. Installation der Hardware 4

3. Konfiguration des drahtlosen Routers 6

Page is loading ...

1. I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message

says “The page cannot be displayed.” How can I get into the TEW-692GR's web

configuration page?

1. Check your hardware settings again by following the instructions in Section 2.

2. Make sure the Network Port and Wireless lights are lit.

3. Make sure your TCP/IP settings are set to Obtain an IP address automatically (see the

steps below).

4. If you are still having problems, reset the TEW-692GR. To reset the TEW-692GR, take a

pin or paperclip and press the reset button on the back of the wireless router for 20

seconds. Then let go.

Troubleshooting

Windows 7

Windows Vista

1. Go into the Control Panel, click Network and

Internet, click Network and Sharing Center, click

Change Adapter Settings and then right-click the

Local Area Connection icon and then click

Properties.

2. Click Internet Protocol Version 4(TCP/IPv4) and

then click Properties. Then click on Obtain an IP

address automatically.

1. Go into the Control Panel, click Network

and Internet, click Network and Sharing

Center, click Manage Network Connections

and then right-click the Local Area

Connection icon and then click Properties.

2. Click Internet Protocol Version 4(TCP/IPv4) and

then click Properties. Then click on Obtain an IP

address automatically.

2. I am not sure what type of Internet Account Type I have for my Cable/DSL connection.

How do I find out?

Contact your Internet Service Provider's (ISP) support service for the correct information.

3. I configured my router with my ISP settings, but I cannot get onto the Internet. What

should I do?

1. Verify that you can get onto the Internet with a direct connection into your modem.

2. Contact your ISP and verify all the information that you have in regards to your Internet

connection settings is correct.

3. Power cycle your modem and router. Unplug the power to the modem and router. Wait

30 seconds, and then reconnect the power to the modem. Wait for the modem to fully

boot up, and then reconnect the power to the router.

4. All the settings are correct, but I cannot make a wireless connection to the Router. What

should I do?

1. Double check that the WLAN light on the Router is lit.

2. Power cycle the TEW-692GR. Unplug the power to the router. Wait 30 seconds and then

reconnect the power to the router.

3. Contact the manufacturer of your wireless network adapter and make sure the wireless

network adapter is configured with the proper SSID. The default SSID of the TEW-692GR

is TRENDnet692_2.4GHz and TRENDnet692_5GHz. If you have enabled any encryption

on the TEW-692GR, make sure to configure the wireless network adapter with the same

wireless security password.

5. When I connect a computer to the router's LAN port, I am not getting Gigabit speeds.

What should I do?

1. Make sure that you have a Gigabit Ethernet adapter installed.

2. Make sure to use a Cat-5e or Cat 6 network cable. Some CAT-5 cables are not rated to

run in Gigabit.

2. Click Internet Protocol (TCP/IP) and then

click Properties. Then click on Obtain an IP

address automatically.

Windows XP/2000

1. Go into the Control Panel, double-click the

Network Connections icon and then

right-click the Local Area Connection icon

and then click Properties.

LED/Button

Power LED

Green Solid

Network Port

Link/Act LEDs

(Ports 1-4)

N/A Off

WAN Link/Act LED

Green

Solid

Wireless (2.4GHz)

LED

Amber

Blinking

Wireless (5GHz)

LED

WPS LED

N/A

Solid

Power Switch

(EU Version only)

Green

Blinking

Reset Button

Amber

Green

Off

WPS Button

N/A

Solid

Green

Blinking

N/A

Solid

Blue

Blinking

N/A

Off

N/A

Blinking

N/A

Off

Blinking

N/A

Off

N/A

Color

Sequence

Definition

Device is on

LAN port connected at 10/20 Mbps or 100/200Mbps

(Half/Full Duplex)

LAN port data transmitting/receiving at 2000Mbps

(Full Duplex)

LAN port is disconnected/No Ethernet Link

WAN port data transmitting/receiving at 10/20Mbps

or 100/200Mbps (Half/Full Duplex)

WAN port data transmitting/receiving at 2000Mbps

(Full Duplex)

WPS authentication in process

Wireless LAN (2.4GHz) is on or enabled/Wireless data

transmission

Wireless LAN (5GHz) is on or enabled/Wireless data

transmission

Turns on/off power to the TEW-692GR

Hold 20 seconds to reset device to factory defaults

Hold 3 seconds to activate WPS

Device is off

LAN port data transmitting/receiving 10/20Mbps

or 100/200Mbps (Half/Full Duplex)

LAN port is connected at 2000Mbps (Full Duplex)

WAN port is connected at 10/20Mbps or 100/200Mbps

(Half/Full Duplex)

WAN port is connected at 2000Mbps (Full Duplex)

WPS authentication process complete

WAN port is disconnected/No Ethernet Link

WPS is not activated or disabled

Wireless LAN (2.4GHz) is off or disabled

Wireless LAN (5GHz) is off or disabled

If you still encounter problems or have any questions regarding the TEW-692GR, please contact

TRENDnet's Technical Support Department.

6. Please give me an explanation of all the LEDs and Buttons.

The following are some general wireless tips to help minimize the impact of interference within an

environment.

Assign your network a unique SSID

Do not use anything that would be identifying like “Smith Family Network”. Choose

something that you would easily identify when searching for available wireless networks.

Do not turn off the SSID broadcast

The SSID broadcast is intended to be on and turning it off can cause connectivity issues.

The preferred method of securing a wireless network is to choose a strong form of encryption

with a strong and varied encryption key.

Change the channel

Most wireless access points and routers are defaulted to channel 6. If you have a site survey

tool that will display the channels you can plan your channel selection around neighboring

access points to minimize interference from them. If your site survey tool does not display

the channel try using channels 1 or 11.

Change the channel bandwidth

If you are using an 802.11n router or access point you can also make the following changes.

Change the channel bandwidth to 20/40MHz. This will provide the highest possible

performance using an 802.11n device. Also, if using 802.11n you should be securing the

network with WPA2 security.

Avoid stacking hardware on top of each other to prevent overheating issues

Maintain enough free space around the hardware for good ventilation and airflow. There

should also be plenty of free space around the antennas to allow the wireless signal to

propagate. Please also make sure that the wireless hardware is not placed in any type of

shelving or enclosures.

There are a number of other environmental factors that can impact the range of wireless

devices.

1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at

an angle. The more material the signal has to pass through the more signal you will lose.

Note: after setting up the SSID, encryption type and encryption key/passphrase, please

make a note of them for future reference. You will need this information to connect your

wireless computers to the wireless router/access point.

Note: Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP

encryption this device may operate in legacy wireless mode (802.11b/g). You may not get

802.11n performance as these forms of encryption are not supported by the 802.11n

specification.

Wireless Tips

2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of

a wireless device. Position the wireless devices in a manner that will minimize the amount

of obstructions between them.

3. Building materials can have a large impact on your wireless signal. In an indoor

environment, try to position the wireless devices so that the signal passes through less

dense material such as dry wall. Dense materials like metal, solid wood, glass or even

furniture may block or degrade the signal.

4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless

adapter's site survey tool to determine the best antenna orientation for your wireless

devices.

5. Interference from devices that produce RF (radio frequency) noise can also impact your

signal. Position your wireless devices away from anything that generates RF noise, such

as microwaves, HAM radios, Walkie-Talkies and baby monitors.

6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as

2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency

can potentially drop the wireless signal. Although the phone may not be in use, the base

can still transmit wireless signals. Move the phone's base station as far away as possible

from your wireless devices.

If you are still experiencing low or no signal consider repositioning the wireless devices or installing

additional access points. The use of higher gain antennas may also provide the necessary

coverage depending on the environment.

Page is loading ...

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received. Including interference that may

cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

Waste electrical and electronic products must not

be disposed of with household waste. Please

recycle where facilities exist. Check with you Local

Authority or Retailer for recycling advice.

ADVERTENCIA

En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de

alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al

mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador

de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria

existente en el pais o zona de instalación.

Product Warranty Registration

Please take a moment to register your product online.

Go to TRENDnet’s website at http://www.trendnet.com/register

Trendnet RB-TEW-692GR Owner's manual

Brand: Trendnet

Model: RB-TEW-692GR

Category: Networking

Type: Owner's manual

This manual is also suitable for

TEW-692GR

Download PDF

report

in other languages

Deutsch: Trendnet RB-TEW-692GR Bedienungsanleitung

Trendnet RB-TEW-692GR Owner's manual

This manual is also suitable for

Trendnet RB-TEW-692GR Owner's manual

in other languages

Related papers

Other documents