Mitsubishi JC-17W41 User manual

Brand: Mitsubishi

Model: JC-17W41

Category: Monitors CRT

Type: User manual

This manual is also suitable for

FE750 Plus

USER'S MANUAL

To learn about other special offers, register your product online at www.necmitsubishi.com/ productregistration

MultiSync

™

FE750+

Fe750+.wpc 11/1/00, 10:45 AM1

Page is loading ...

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to

C.S.A. 22.2 #950.

FCC Information

Use the attached specified cables with the JC-17W41

color monitors so as not to interfere with radio

and television reception.

(1) Please use the supplied power cable or equivalent to ensure FCC compliance.

(2) Shielded captive type signal cable.

Use of other cables and adapters may cause interference with radio and television

reception.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for

additional suggestions. The user may find the following booklet, prepared by the Federal Communica-

tions Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet

is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-

00345-4.

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE

THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS

CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING

CAUTION

RISK OF ELECTRIC SHOCK • DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This

symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this

unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Fe750+.wpc 11/1/00, 10:45 AM3

Your new NEC MultiSync

FE750+

™

monitor box* should contain

the following:

• MultiSync FE750+ Monitor with tilt/swivel base

• Power Cord

• Captive Signal Cable

• User’s Manual

Contents

Power Cord

User’s Manual

* Remember to save your original box and packing material to transport or ship the monitor.

Captive Signal Cable

USER'S MANUAL

To learn about other special offers, register your product online at www.necmitsubishi.com/ productregistration

MultiSync

™

FE750

Fe750+.wpc 11/1/00, 10:45 AM4

Quick Start

Figure A.1

To attach the MultiSync

FE750+

™

monitor to your system, follow

these instructions:

1. Turn off the power to your computer.

2. If necessary, install the display card into your system. For more information,

refer to the display card manual.

3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the

connector of the display card in your system (Figure A.1). Tighten all screws.

For the Mac: Connect the MultiSync FE750+ Macintosh cable adapter (not

included) to the monitor connector on the Macintosh (Figure B.1). Attach the

15-pin mini D-SUB end of the captive signal cable to the MultiSync FE750+

Macintosh cable adapter on the computer (Figure B.1). Tighten all screws.

NOTE: To obtain the MultiSync FE750+ Macintosh cable adapter, call

NEC-Mitsubishi Electronics Display of America, Inc. at (800) 820-1230.

4. For download information on the Windows

95/98/2000 INF file for your

MultiSync monitor, refer to the References section of this User’s Manual.

5. Connect one end of the power cord to the MultiSync FE750+ monitor and the

other end to the power outlet (Figure C.1).

6. Turn on the monitor (Figure D.1) and the computer.

NOTE: If you have any problems, please refer to the Troubleshooting section of

this User’s Manual.

Fe750+.wpc 11/1/00, 10:45 AM5

EXIT PROCEED RESET

+–

Figure D.1

Figure C.1

Figure B.1

Quick Start –continued

Power Button

Fe750+.wpc 11/1/00, 10:45 AM6

Controls

OSM

™

(On-Screen Manager) control buttons on the front of the monitor function

as follows:

Main Menu Sub-Menu

EXIT Exits the OSM menu. Exits to the OSM controls

main menu.

CONTROL Moves the highlighted Moves the highlighted area

/ area up/down to select up/down to select one of the

one of the controls. controls.

CONTROL Moves the highlighted Moves the bar in the – or +

–/+ area left/right to select direction to decrease or

one of the controls. increase the adjustment.

PROCEED Has no function. Only executes control

or enters sub, sub-menu.

RESET Resets all the controls within Resets the highlighted control

the highlighted menu to the factory setting.

to the factory setting.

NOTE: When RESET is pressed in the main and sub-menu, a warning

window will appear allowing you to cancel the reset function.

When OSM controls are activated, icons are displayed at the top of the menu.

If an arrow (➔) is displayed in a sub-menu, it indicates further choices are

available. To enter a sub, sub-menu, press PROCEED.

Brightness/Contrast Controls

Brightness: Adjusts the overall image and background screen brightness.

Contrast: Adjusts the image brightness in relation to the background.

Degauss: Eliminates the buildup of stray magnetic fields which alter the correct

scan of the electron beams and affect the purity of the screen colors, focus and

convergence. When activated, your screen image will jump and waver a bit as

the screen is demagnetized.

Caution: Please allow a minimum of 20 minutes to elapse between uses of the

Degauss Control.

Size and Position Controls

Left/Right: Moves the image horizontally (left or right).

Down/Up: Moves the image vertically (up or down).

Narrow/Wide: Decreases or increases the horizontal size of the image.

Short/Tall: Decreases or increases the vertical size of the image.

Fe750+.wpc 11/1/00, 10:45 AM7

Color Control/AccuColor

Control System

Color presets 1 through 5 selects the desired color setting. The bar is replaced

by the color setting choice from 1 to 5. Each color setting is adjusted at the

factory to the stated Kelvin. If a setting is adjusted, the name of the setting will

change from Kelvin to Custom.

Red, Green, Blue: AccuColor Control System decreases or increases the

monitor's red, green or blue color guns depending upon which is selected. The

change in color will appear on screen and the direction (decrease or increase)

will be shown by the bars.

sRGB Mode: sRGB mode provides the suitable color managed picture image.

You can not change Red, Green and Blue colors individually.

Geometry Controls

Geometry Controls Menu

The Geometry controls allow you to adjust the curvature or angle of the sides of

your display.

Sides In/Out (pincushion): Decreases or increases the curvature of the sides either

inward or outward.

Sides Left/Right (pincushion balance): Decreases or increases the curvature of

the sides either to the left or right.

Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the

left or right.

Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be

the same as the top.

Rotate (raster rotation): Rotates the entire display clockwise or counterclockwise.

Tools 1

Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen.

The pattern is repetitive and superimposed as rippled images. When running certain

applications, the wavy pattern is more evident than in others. To reduce moiré, adjust

the level by using –/+ CONTROL buttons.

Basic Convergence:

Aligns all three colors (R,G,B) to form a single color (white).

The purpose of this control is to ensure that a white line drawn on the screen is

as crisp and clear as possible.

• Use the Horizontal control to adjust the alignment of the white lines in the

up/down direction.

• Use the Vertical control to adjust the alignment of the white lines in the left/

right direction.

Corner Correction:

Allows you to adjust the geometry of the corners of your

display — Top, Top Balance, Bottom or Bottom Balance.

Auto Save:

The monitor automatically saves the last settings of the user controls.

You can turn this Auto Save feature off by selecting this menu and changing the

off position. When the off mode is selected, you will prompted with the option to

Controls –continued

Fe750+.wpc 11/1/00, 10:45 AM8

Controls –continued

save or return to the previous setting once you select a different control. If the

save is not confirmed, the setting will go back to previous setting when OSM turns off.

Factory Preset: Selecting Factory Preset allows you a reset most OSM

™

control

settings back to the factory settings. A warning statement will appear to confirm

that you do want to reset ALL settings. Individual settings can be reset by high-

lighting the control to be reset and pressing the RESET button.

Tools 2

Language: OSM controls menus are available in six languages.

OSM Position: You can choose where you would like the OSM controls menu to

appear on your screen. Selecting OSM Position allows you to manually adjust the

OSM controls menu position from among Center, Top left, Top right, Bottom left

and Bottom right.

OSM Turn Off: The OSM controls menu will stay on as long as it is in use. In the

OSM Turn Off sub-menu, you can select how long the monitor waits after the last

touch of a button for the OSM controls menu to disappear. The preset choices

are 10, 20, 30, 45, 60 and 120 seconds.

SM Lock Out: This control completely locks out access to all OSM controls

functions except Brightness and Contrast. When attempting to activate OSM

controls while in the lock out mode, a screen will appear indicating that OSM

controls are locked out. To activate the OSM Lock Out function, press PROCEED,

then press

and hold down simultaneously. To deactivate the OSM Lock Out,

press PROCEED, then press

and hold down simultaneously.

IPM

™

System Off Mode:

Enable: The IPM System works normally and all

stages of energy savings are utilized.

Disable: The Off Mode of the IPM System is not used.

OTE: For standard systems and graphics boards, keep the factory setting

at ENABLE

EdgeLock

Control: Operating your monitor at a non-standard timing may

cause images to appear darker than normal or have color distortion. Use of the

EdgeLock control will adjust images to their normal state.

Information

Display Mode: Indicates the current mode and frequency setting of the monitor.

Monitor Info: Indicates the model and serial numbers of your monitor.

Refresh Notifier: A message will advise you if the refresh rate of the signal being

applied to the monitor by the computer is too low. For further information, please

refer to your display card or system manual.

Fe750+.wpc 11/1/00, 10:45 AM9

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTISYNC

FE750+

™

COLOR MONITOR:

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and

opening or removing covers may expose you to dangerous shock hazards or other

risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch danger-

ous voltage points, which can be harmful or fatal or may cause electric shock, fire

or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may

cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the

monitor may fall, causing serious damage to the monitor.

• Keep the monitor away from high capacity transformers, electric motors and other

devices such as external speakers or fans, which may create strong magnetic

fields.

• If possible, position the monitor so that it is facing the east to minimize the effects

of the earth’s magnetic field.

• Changing the direction of the monitor while it is powered on may cause image

discoloration. To correct this, turn the monitor off for 20 minutes before powering

it back on.

• When operating the MultiSync FE

750+ with its AC 220-240V worldwide power

supply, use a power supply cord that matches the power supply voltage of the AC

power outlet being used. The power supply cord you use must have been ap-

proved by and comply with the safety standards of your country. (Type H05VV-F

should be used except in UK)

• In UK, use a BS-approved power cord with molded plug having a black (5A) fuse

installed for use with this monitor. If a power cord is not supplied with this monitor,

please contact your supplier.

Immediately unplug your monitor from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

• Allow adequate ventilation around the monitor so that heat can properly

dissipate. Do not block ventilated openings or place the monitor near a

radiator or other heat sources. Do not put anything on top of monitor.

• The power cable connector is the primary means of detaching the system

from the power supply. The monitor should be installed close to a power

outlet which is easily accessible.

• Handle with care when transporting. Save packaging for transporting.

Recommended Use

CAUTION

Fe750+.wpc 11/1/00, 10:45 AM10

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR

CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

Recommended Use –continued

• Adjust the monitor height so that the top of

the screen is at or slightly below eye level.

Your eyes should look slightly downward

when viewing the middle of the screen.

• Position your monitor no closer than 12 inches

and no further away than 28 inches from your

eyes. The optimal distance is 24 inches.

• Rest your eyes periodically by focusing on

an object at least 20 feet away. Blink often.

• Position the monitor at a 90° angle to

windows and other light sources to minimize

glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect

on your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a

non-alcohol, neutral, non-abrasive cleaning solution or glass cleaner to

minimize dust.

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or

reference material) directly in front of you to minimize turning your head

while you are typing.

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Adjust the Brightness until the background raster disappears

• Do not position the Contrast control to its maximum setting

• Use the preset Size and Position controls with standard signals

• Use the preset Color Setting and Sides Left/Right controls

• Use non-interlaced signals with a vertical refresh rate between 75-120Hz

• Do not use primary color blue on a dark background, as it is difficult to see

and may produce eye fatigue due to insufficient contrast

For more detailed information on setting up a healthy work environment, call NEC-

Mitsubishi Electronics Display at (800) 820-1230, NEC FastFacts

™

information at (800)

366-0476 and request document #900108 or write the American National Standard for

Human Factors Engineering of Visual Display Terminal Workstations – ANSI-HFS

Standard No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa

Monica, California 90406.

Fe750+.wpc 11/1/00, 10:45 AM11

Specifications

Monitor MultiSync

FE750+

™

Notes

Specifications Monitor

Picture Tube Diagonal: 17 inch 90° deflection, 0.25 mm grille pitch,

Viewable Image Size: 16 inch medium short persistence phosphor,

Radius: 50,000 mm aperture grille CRT, multi-layered, anti-static

screen coating, dark-tint screen and

OptiClear

screen.

Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms

Sync: Separate sync. TTL Level

Horizontal sync. Positive/Negative

Vertical sync. Positive/Negative

Composite sync. (Positive/Negative) (TTL Level)

Display Colors Analog input: Unlimited number of Colors Depends on display card used.

Synchronization Horizontal: 31 kHz to 96 kHz Automatically

Range Vertical: 55 Hz to 160 Hz Automatically

Resolutions Supported 640 x 480 @ 60 to 160 Hz

Some systems may not support

Resolution based on

horizontal and

800 x 600 @ 55 to 146 Hz

all modes listed.

vertical frequencies only

832 x 624 @ 55 to 141 Hz

1024 x 768 @ 55 to 116 Hz

1152 x 870 @ 55 to 103 Hz

1280 x 1024 @ 55 to 89 Hz .....................

NEC-Mistubishi Electronics Display cites

1600 x 1200 @ 55 to 76 Hz

recommended resolution at 85 Hz for

optimal display performance.

Active Display Area Horizontal:

315 mm/12.4 inches Dependent upon signal timing used,

(Factory Setting) Vertical:

236 mm/9.3 inches and does not

include border area.

Active Display Area

325 mm/12.8 inches Dependent upon signal timing used,

(Full Scan)

244 mm/9.6 inches and does not

include border area.

Power Supply AC 100–120 V/220-240 V, 50/60 Hz

Current Rating 1.3A @ 100-120 V, 0.6 A@ 220-240 V

Dimensions

399 mm (W) x 413 mm (H) x 415 mm (D)

15.7 inches (W) x 16.3 inches (H) x 16.4 inches (D)

Weight 19.0 kg

41.9 lbs

Environmental Considerations

Operating Temperature: +10°C to +35°C / +50° F to +95°F

Humidity: 30% to 80%

Feet: 0 to 10,000 Feet

Storage Temperature: -20°C to +60°C / -4°F to +140° F

Humidity: 10% to 90%

Feet: 0 to 45,000 Feet

NOTE: Technical specifications are subject to change without notice.

Fe750+.wpc 11/1/00, 10:45 AM12

Features

Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a

virtually flat image, eliminating distortion and reducing glare so that what you

see on-screen is what you get on your printed output. The striped phosphor

alignment of the CRT delivers superior vertical definition with improved bright-

ness for more uniform image contrast.

OptiClear

Screen Surface: Reduces reflection and glare and increases contrast

without sacrificing focus level, clarity or brightness. Along with the flat square

technology CRT, a high contrast screen with 0.25 mm grille pitch delivers crisp,

clean text and graphics.

Dual Dynamic Beam Focus: Provides precise, continuous focus adjustments of the

electron beams and optimum image quality, even to the far edges of the screen.

AccuColor

Control System: Allows you to change between five color settings on

your display to match your personal preference.

OSM

™

(On-Screen Manager) Controls: Allows you to quickly and easily adjust

all elements of your screen image via simple to use on-screen menus.

ErgoDesign

Features: Enhances human ergonomics to improve the working

environment, protect the health of the user and save money. Examples include

OSM controls for quick and easy image adjustments, tilt/swivel base for pre-

ferred angle of vision and compliance with MPRII guidelines for lower emissions.

Plug and Play: The Microsoft

solution with the Windows

95/98/2000

operating system facilitates setup and installation by allowing the monitor to send

its capabilities (such as screen size and resolutions supported) directly to your

computer, automatically optimizing display performance.

IPM

™

(Intelligent Power Manager) System: Provides innovative power-saving

methods that allow the monitor to shift to a lower power consumption level when

on but not in use, saving two-thirds of your monitor energy costs, reducing

emissions and lowering the air conditioning costs of the workplace.

Reduced Magnetic Field

™

Technology: Reduces magnetic and alternating electric

field emissions and static electricity, addressing ergonomic concerns regarding

potential risks from extended computer monitor use.

Multiple Frequency Technology: Automatically adjusts monitor to the display

card’s scanning frequency, thus displaying the resolution required.

FullScan

™

Capability: Allows you to use the entire screen area in most

resolutions, significantly expanding image size.

NEC-Mitsubishi Electronics Display of America, Inc.

Fe750+.wpc 11/1/00, 10:45 AM13

Troubleshooting

No picture

• Display card should be completely seated in its slot.

• Power Button and computer power switch should be in the ON position.

• Signal cable should be completely connected to display card/computer.

• Check connector for bent or pushed-in pins.

Image is scrolling or unstable

• Signal cable should be completely attached to the computer.

• Check pin assignments and signal timings of the monitor and your display card with

respect to recommended timings and pin assignments.

• If the Macintosh cable adapter is used, check for proper connection or make sure the

display card is Macintosh compatible and that the card is properly seated in the

computer.

LED on monitor is not lit

(no green, orange color can be seen)

• Power Switch should be in the ON position and power cord should be connected.

Picture is fuzzy or color looks blotchy

• Adjust Brightness and Contrast Controls.

• Access the Degauss Control through OSM™ controls. Activate the

Degauss Control.

CAUTION: A minimum interval of 20 minutes should elapse before the

Deguass Control is used a second time when not switching

between modes.

Picture bounces or a wavy pattern is present

in the picture

• Move electrical devices that may be causing electrical interference away

from the monitor.

• See inside cover of User’s Manual for FCC information.

Edges of the display image are not square

• Use the OSM Geometry Controls to straighten the edges.

• If possible, position the front of the monitor facing east.

Display image is not centered, too small, or too large

• Use the OSM Size and Position Controls to adjust the image.

Thin lines appear on your screen

• Thin lines are normal for an aperture grille CRT and are not a malfunction.

These are shadows from the damper wires used to stabilize the aperture grille and

are most noticeable when the screen’s background is light (usually white).

Black vertical lines are visible on the screen

• Thin vertical black lines on one or both sides of the screen. This minor condition is

caused by grille element overlap which can occur during shipping.

• Position an open white window over the affected area of the screen and maximize

the brightness and contrast controls. This will cause localized heating of the overlap

which will clear in a few minutes. Be sure to readjust the brightness and contrast

controls back to the normal viewing level after this procedure.

Fe750+.wpc 11/1/00, 10:45 AM14

References

• BBS (978) 742-8706

NEC-Mitsubishi Electronics Display Remote Bulletin Board System is an

electronic service accessible with your system and a modem. Communication

parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no

parity, 8-data bits, 1 stop bit

• Customer Service/

Technical Support (800) 632-4662

Fax (978) 742-7049

• Electronic Channels:

Internet e-mail: [email protected]

Internet ftp site: ftp.necmitsubishi.com

World Wide Web: http://www.necmitsubishi.com

Product Registration:

http://www.necmitsubishi.com/productregistration

European Operations: htt://www.nec-monitors.com

Windows

95/98/2000 INF File: http://support.necmitsubishi.com/software.htm

then download the file NECMSINF.ZIP

• FastFacts™ Information (800) 366-0476

INFORMATION DESCRIPTION DOCUMENT #

Glossary Definition of terms related 900203

to functions, features and

installation of the

MultiSync

monitor

More Information Names and addresses of 900204

other groups involved in

standards and features of

the MultiSync monitor

Macintosh Connection Detailed information on 153006

connecting the MultiSync

monitor to a Macintosh

Healthy Work Environment Detailed information on 900108

setting up a healthy work

environment

• Literature & Sales Info (800) NEC-INFO [(800) 632-4636]

• MultiSync Fulfillment (800) 820-1230

[For software & accessories]

• TeleSales (800) 284-4484

Fe750+.wpc 11/1/00, 10:45 AM15

NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this

Product to be free from defects in material and workmanship and, subject to the conditions set

forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit

which proves defective for a period of three (3) years from the date of first consumer purchase.

Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or

refurbished and will meet specifications of the original parts or unit.

This warranty gives you specific legal rights and you may also have other rights, which vary

from state to state. This warranty is limited to the original purchaser of the Product and is not

transferable. This warranty covers only NMD-A-supplied components. Service required as a

result of third party components is not covered under this warranty. In order to be covered

under this warranty, the Product must have been purchased in the U.S.A. or Canada by the

original purchaser. This warranty only covers Product distribution in the U.S.A. or Canada by

NMD-A. No warranty service is provided outside of the U.S.A. or Canada. Proof of Purchase

will be required by NMD-A to substantiate date of purchase. Such proof of purchase must be

an original bill of sale or receipt containing name and address of seller, purchaser, and the

serial number of the product.

It shall be your obligation and expense to have the Product shipped, freight prepaid, or

delivered to the authorized reseller from whom it was purchased or other facility authorized

by NMD-A to render the services provided hereunder in either the original package or a

similar package affording an equal degree of protection. All Products returned to NMD-A for

service MUST have prior approval, which may be obtained by calling 1-800-632-4662. The

Product shall not have been previously altered, repaired, or serviced by anyone other than a

service facility authorized by NMD-A to render such service, the serial number of the product

shall not have been altered or removed. In order to be covered by this warranty the Product

shall not have been subjected to displaying of fixed images for long periods of time resulting

in image persistence (afterimage effects), accident, misuse or abuse or operated contrary to

the instructions contained in the User’s Manual. Any such conditions will void this warranty.

NMD-A SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,

OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NMD-A PRODUCT

OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF ALL

OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE

LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAM-

AGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

This Product is warranted in accordance with the terms of this limited warranty. Consumers

are cautioned that Product performance is affected by system configuration, software, the

application, customer data, and operator control of the system, among other factors. While

NMD-A Products are considered to be compatible with many systems, specific functional

implementation by the customers of the Product may vary. Therefore, suitability of a Product

for a specific purpose or application must be determined by consumer and is not warranted

by NMD-A.

For the name of your nearest authorized NEC-Mitsubishi Electronics Display of America

service facility, contact NEC-Mitsubishi Electronics Display of America at 1-800-632-4662.

Limited Warranty

Fe750+.wpc 11/1/00, 10:45 AM16

TCO’99

Congratulations! You have just purchased a TCO’99 approved and

labeled product! Your choice has provided you with a product devel-

oped for professional use. Your purchase has also contributed to

reducing the burden on the environment and also to the further

development of environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encourag-

ing the adaptation of goods and services to the environment. The main problem, as far as

computers and other electronics equipment are concerned, is that environmentally harmful

substances are used both in the products and during the manufacturing. Since it has not been

possible for the majority of electronics equipment to be recycled in a satisfactory way, most

of these potentially damaging substances sooner or later enter Nature.

There are also other characteristics of a computer, such as energy consumption levels, that are

important from the viewpoints of both the work (Internal) and natural (external) environments.

Since all methods of conventional electricity generation have a negative effect on the

environment (acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to

conserve energy. Electronics equipment in offices consume an enormous amount of energy

since they are often left running continuously.

What does labelling involve?

This product meets the requirements for the TCO’99 scheme which provides for international and

environmental labelling of personal computers. The labelling scheme was developed as a joint

effort by the TCO (The Swedish Confederation of Professional Employees), Svenska

Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet

(The Swedish National Energy Administration).

The requirements cover a wide range of issues: environment, ergonomics, usability, emission of

electrical and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands concern restrictions on the presence and use of heavy metals,

brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other

things. The product must be prepared for recycling and the manufacturer is obliged to have an

environmental plan which must be adhered to in each country where the company implements its

operational policy. The energy requirements include a demand that the computer and/or display,

after a certain period of inactivity, shall reduce its power consumption to a lower level in one or

more stages. The length of time to reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction

of electric and magnetic fields, physical and visual ergonomics and good usability.

Environmental Requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn,

they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of

flame retardant substances. Most flame retardants contain bromine or chloride and these are

related to another group of environmental toxins, PCBs, which are suspected to give rise to severe

health effects, including reproductive damage in fisheating birds and mammals, due to the bio-

Fe750+.wpc 11/1/00, 10:45 AM17

TCO’99 –continued

accumulative* processes. Flame retardants have been found in human blood and researchers fear

that disturbances in foetus development may occur.

TCO’99 demand requires that plastic components weighing more than 25 grams must not contain

flame retardants with organically bound chlorine and bromine. Flame retardants are allowed in

the printed circuit boards since no substitutes are available.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the

nervous system and in higher doses, causes lead poisoning.

TCO’99 requirement permits the inclusion of lead since no replacement has yet been developed.

Cadmium**

Cadmium is present in rechargeable batteries and in the colourgenerating layers of certain

computer displays. Cadmium damages the nervous system and is toxic in high doses.

TCO’99 requirement states that batteries, the colourgenerating layers of display screens and the

electrical or electronics components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches, Mercury damages the nervous system

and is toxic in high doses.

TCO’99 requirement states that batteries may not contain any Mercury. It also demands that no

mercury is present in any of the electrical or electronics components associated with the display unit.

CFCs (freons)

CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and

thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of

ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).

The relevant TCO’99 requirement; Neither CFCs nor HCFCs may be used during the manufacturing

and assembly of the product or its packaging.

*Bio-accumulative is defined as substances which accumulate within living organisms.

**Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

To obtain complete information on the environmental criteria document, order from:

TCO Development Unit

SE-114 94 Stockholm

SWEDEN

FAX Number: +46 8 782 92 07

E-mail (Internet): [email protected]

You may also obtain current information on TCO’99 approved and labelled products by

visiting their website at: http://www.tco-info.com/

Fe750+.wpc 11/1/00, 10:45 AM18

Declaration of the Manufacturer

We hereby certify that the color monitor

MultiSync

FE750+

(JC-17W41) is in

compliance with

Council Directive 73/23/EEC:

– EN 60950

Council Directive 89/336/EEC:

— EN 55022

— EN 61000-3-2

— EN 61000-3-3

— EN 55024

(IEC-61000-4-2)

(IEC-61000-4-3)

(IEC-61000-4-4)

(IEC-61000-4-5)

(IEC-61000-4-6)

(IEC-61000-4-8)

(IEC-61000-4-11)

and marked with

NEC-Mitsubishi Electric Visual

Systems Corporation

686-1, Nishioi Oi-Machi

Ashigarakami-gun

Kanagawa 258-8533, Japan

Röntgenstrahlung

Die in diesem Gerät erzeugten Röntgenstrahlen sind durch die eigensichere

Kathodenstrahlröhre ausreichend abgeschirmt.

Unsachgemäße Eingriffe, insbesondere Verändern der Hochspannung oder Einbau eines

anderen Bildröhrentyps, können dazu führen, daß Röntgenstrahlung in erheblicher Stärke

auftritt. So veränderte Geräte entsprechen nicht mehr dieser Zulassung und dürfen nicht

betrieben werden.

Fe750+.wpc 11/1/00, 10:45 AM19

Page is loading ...

Contenu

Guide de l’utilisateur

* Ne pas oublier de conserver la boîte et le matériel d’emballage d’origine pour transporter ou

expédier le moniteur.

Cordon d’alimentation

La boîte* de votre nouveau moniteur NEC MultiSync

FE750+

contient :

• Moniteur MultiSync FE750+ avec socle inclinable/rotatif

• Cordon d’alimentation

• Câble de signal captif

• Guide de l’utilisateur

Câble de signal captif

USER'S MANUAL

To learn about other special offers, register your product online at www.necmitsubishi.com/ productregistration

MultiSync

™

FE750+

Fe750+.wpc 11/1/00, 10:45 AM22

Page is loading ...

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related materials, is the valuable property of

NEC-Mitsubishi Electronics Display and/or its licensors, as appropriate, reserve all patent, copyright and other

proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except

to the extent said rights are expressly granted to others.

The NEC-Mitsubishi Electronics Display product(s) discussed in this document are warranted in accordance with the terms

of the Limited Warranty Statement accompanying each product. However, actual performance of each such product is

dependent upon factors such as system configuration, customer data and operator control. Since implementation by

customers of each product may vary, the suitability of specific product configurations and applications must be

determined by the customer and is not warranted by NEC-Mitsubishi Electronics Display.

To allow for design and specification improvements, the information in this document is subject to change at any time

without notice. Reproduction of this document or portions thereof without prior approval of NEC-Mitsubishi Electronics

Display is prohibited.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

U.S. Responsible Party: NEC-Mitsubishi Electronics Display of America, Inc.

Address: 1250 N. Arlington Heights Road

Itasca, Illinois 60143

Tel. No.: (630) 467-3000

Type of Product: Computer Monitor

Equipment Classification: Class B Peripheral

Models: JC-17W41

We hereby declare that the equipment specified above

conforms to the technical standards as specified in the FCC Rules.

Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ENERGY STAR is a U.S.

registered trademark. All other brands and product names are trademarks or registered trademarks of their respective owners.

As an ENERGY STAR

Partner, NEC-Mitsubishi Electronics Display of America, Inc. has determined that this product meets the ENERGY

STAR guidelines for energy efficiency. The ENERGY STAR emblem does not represent EPA endorsement of any product or service.

NEC Flat Enterprises Series

Part No. 15500801

Printed in China

Fe750+.wpc 11/1/00, 10:46 AM60

Mitsubishi JC-17W41 User manual

Brand: Mitsubishi

Model: JC-17W41

Category: Monitors CRT

Type: User manual

This manual is also suitable for

FE750 Plus

Download PDF

report

in other languages

français: Mitsubishi JC-17W41 Manuel utilisateur
Deutsch: Mitsubishi JC-17W41 Benutzerhandbuch

Mitsubishi JC-17W41 User manual

This manual is also suitable for

Mitsubishi JC-17W41 User manual

in other languages

Related papers

Other documents