SICK SENSICK AT20E EDGE/PROXIMITY Operating instructions

Category
Convenience lighting
Type
Operating instructions
ENGLISH
Array Sensor
with Edge Detection / Proximity
Operating instructions
Safety specications
Read the operating instructions before starting operation.
Connection, assembly, and settings only by competent technicians.
Protect the device against moisture and soiling when operating.
No safety component in accordance with EU machine guidelines.
The sensor AT20D / E is equipped with LEDs. The sensor meets the
criteria of risk group 1 according to IEC 62471:2006 (relevant hazard:
retinal blue light hazard). No special measures are required (e. g. eye
protection).
Proper use
The array sensor AT20E is an opto-electronic sensor and is used for optical,
non-contact detection of objects / edges through contrast dierences.
Starting operation
1
Sensor plug can be swiveled horizontally and vertically.
Connect and secure cable receptacle tension-free.
The following apply for connection in B: brn = brown, blk = black,
blu = blue, wht = white, gra = gray.
Connect the sensor according to the B connection chart.
Connect sensor to operating voltage (see nameplate);
green power indicator [Power On] must light.
Mount the sensor with mounting holes at the place where the test
object has the least horizontal and vertical movement. Note scanning
range and measurement area (see the technical data at the end of
these operating instructions).
1a Edge detection (E): pay attention to orientation of sensor to the edge
and direction of movement.
S = plug side / K = head side
1b Object detection (O): with edges that have a height dierence, tilt the
sensor approx. 2° to the object surface.
2 Alignment of light reception:
Position object / edge.
2a With reecting or shiny object surfaces, tilt the sensor
5° ... 10° to the material surface. Avoid swaying the sensor.
Rough alignment:
Position light spot on object / edge. White light spot on object / edge
visible.
Transparent and non-transparent objects can be detected in reector
mode.
Mode selection:
Position reector in the light eld during a restart.
2b Tilt the reector 5° ... 10° with respect to the sensor.
Position object and reector according to the table for optimum light
reception:
Type Max. reector
distance
Distance of transpar-
ent object
NM111 / PM111 60 mm 22 ... 26 mm
NM331 / PM331 200 mm 90 ... 110 mm
3 Analog output Q
A
:
Analog output Q
A
(measuring) provides the “position of the rst con-
trast edge in the measurement range with respect to the plug side”:
Switching output Q
P
/ Q
N
(switching / plausibility):
Q
P
/ Q
N
Switching output
indicator (yellow LED)
High O / E in measurement range on
Low O / E not in measurement range o
4
Object position
O / Edge position E
TW 100 mm
Object position
O / Edge position E
TW 25 mm
Analogue output Q
A
0 mm 0 mm 4 mA
30 mm 20 mm 20 mA
15 mm 10 mm 12 mA target
standard size
< 0 mm < 0 mm 3.5 mA, O / E moves
out on plug side
> 30 mm > 20 mm 20.5 mA, O / E moves
out on head side
No edge in
measurement eld
No edge in
measurement eld
3 mA
5 Sensor detects contrast step from black to white.
6 Measurement range / scanning range [TW]:
Only AT20E_ _111: with reference to 50% contrast to white paper.
Only AT20E_ _331: with reference to 30% contrast to white paper.
(typical values)
Maintenance
SICK sensors are maintenance-free.
We recommend doing the following regularly:
- clean the external lens surfaces
- check the screw connections and plug-in connections
No modications may be made to devices.
Subject to change without notice. Specied product properties and technical
data are not written guarantees.
AT20E
EDGE / PROXIMITY
A
1a
B
2a
DEUTSCH
Array Sensor
mit Kantenerkennung / Tasterprinzip
Betriebsanleitung
Sicherheitshinweise
Vor der Inbetriebnahme die Betriebsanleitung lesen.
Anschluss, Montage und Einstellung nur durch Fachpersonal.
Gerät bei Inbetriebnahme vor Feuchte und Verunreinigung schützen.
Kein Sicherheitsbauteil gemäß EU-Maschinenrichtlinie.
Der Sensor AT20D / E ist mit LEDs ausgestattet. Der Sensor entspricht
der Risikogruppe 1 gemäß IEC 62471:2006 (relevante Gefährdung:
Photochemische Netzhautschädigung). Es müssen keine besonderen
Maßnahmen (z. B. zum Schutz der Augen) vorgenommen werden.
Bestimmungsgemäße Verwendung
Der Array Sensor AT20E ist ein optoelektronischer Sensor und wird zum
optischen, berührungslosen Erfassen von Objekten / Kanten anhand von
Kontrastunterschieden eingesetzt.
Inbetriebnahme
1
Gerätestecker horizontal und vertikal schwenkbar.
Leitungsdose spannungsfrei aufstecken und festschrauben.
Für Anschluss in B gilt: brn = braun, blk = schwarz, blu = blau,
wht = weiß, gra = grau.
Sensor laut Anschlussschema B anschließen.
Sensor an Betriebsspannung legen (s. Typenaufdruck);
Betriebsanzeige grün [Power On] muss leuchten.
-------------------------------------------------------- 8012926.ZRQ5 0619 COMAT -----------------------------------------------------
BZ int49
Detailed addresses and further locations at www.sick.com
Australia
Phone +61 (3) 9457 0600
1800 33 48 02 –
tollfree
Austria
Phone +43 (0) 2236 62288-0
Belgium/Luxembourg
Phone +32 (0) 2 466 55 66
Brazil
Phone +55 11 3215-4900
Canada
Phone +1 905.771.1444
Czech Republic
Phone +420 234 719 500
Chile
Phone +56 (2) 2274 7430
China
Phone +86 20 2882 3600
Denmark
Phone +45 45 82 64 00
Finland
Phone +358-9-25 15 800
France
Phone +33 1 64 62 35 00
Germany
Phone +49 (0) 2 11 53 010
Greece
Phone +30 210 6825100
Hong Kong
Phone +852 2153 6300
Hungary
Phone +36 1 371 2680
India
Phone +91-22-6119 8900
Israel
Phone +972 97110 11
Italy
Phone +39 02 27 43 41
Japan
Phone +81 3 5309 2112
Malaysia
Phone +603-8080 7425
Mexico
Phone +52 (472) 748 9451
Netherlands
Phone +31 (0) 30 229 25 44
New Zealand
Phone +64 9 415 0459
0800 222 278 – tollfree
Norway
Phone +47 67 81 50 00
Poland
Phone +48 22 539 41 00
Romania
Phone +40 356-17 11 20
Russia
Phone +7 495 283 09 90
Singapore
Phone +65 6744 3732
Slovakia
Phone +421 482 901 201
Slovenia
Phone +386 591 78849
South Africa
Phone +27 10 060 0550
South Korea
Phone +82 2 786 6321/4
Spain
Phone +34 93 480 31 00
Sweden
Phone +46 10 110 10 00
Switzerland
Phone +41 41 619 29 39
Taiwan
Phone +886-2-2375-6288
Thailand
Phone +66 2 645 0009
Turkey
Phone +90 (216) 528 50 00
United Arab Emirates
Phone +971 (0) 4 88 65 878
United Kingdom
Phone +44 (0)17278 31121
USA
Phone +1 800.325.7425
Vietnam
Phone +65 6744 3732
SICK AG, Erwin-Sick-Strasse 1, D-79183 Waldkirch
More representatives and agencies at www.sick.com ∙ Subject to change
without notice ∙ The specied product features and technical data do not
represent any guarantee.
Weitere Niederlassungen nden Sie unter www.sick.com ∙ Irrtümer
und Änderungen vorbehalten ∙ Angegebene Produkteigenschaften und
technische Daten stellen keine Garantieerklärung dar.
Plus de représentations et d’agences à l’adresse www.sick.com ∙ Sujet à
modication sans préavis ∙ Les caractéristiques de produit et techniques
indiquées ne constituent pas de déclaration de garantie.
Para mais representantes e agências, consulte www.sick.com ∙ Alterações
poderão ser feitas sem prévio aviso ∙ As características do produto e os
dados técnicos apresentados não constituem declaração de garantia.
Altri rappresentanti ed agenzie si trovano su www.sick.com ∙ Contenuti
soggetti a modiche senza preavviso ∙ Le caratteristiche del prodotto e i dati
tecnici non rappresentano una dichiarazione di garanzia.
Más representantes y agencias en www.sick.com ∙ Sujeto a cambio sin
previo aviso ∙ Las características y los datos técnicos especicados no
constituyen ninguna declaración de garantía.
欲了解更多代表机构和代理商信息,请登录 www.sick.com ∙
如有更改, 不另行通知 ∙ 对所给出的产品特性和技术参数
的正确性不予保证。
その他の営業所はwww.sick.com よりご覧ください ・ 予告なしに変更され
ることがあります ・ 記載されている製品機能および技術データは保証を明
示するものではありません。
2006/42/EC
NO
SAFETY
Sensor mit Befestigungsbohrungen an Stelle montieren, an der das
Prüfobjekt die geringsten Höhenbewegungen ausführt. Dabei Tast-
weite und Messbereich beachten (s. technische Daten am Ende dieser
Betriebsanleitung).
1a Kantenerfassung (E): Orientierung Sensor zu Kante und Laufrichtung
beachten.
S = Steckerseite / K = Kopfseite
1b Objekterkennung (O): Bei Kanten mit Höhenunterschied Sensor um
ca. 2° zur Objektoberäche neigen.
2 Justage Lichtempfang:
Objekt / Kante positionieren.
2a Bei spiegelnden oder glänzenden Objektoberächen Sensor um
5° ... 10° zur Materialoberäche neigen. Tastschwankungen
vermeiden.
Grobjustierung:
Lichteck auf Objekt/Kante ausrichten. Weißer Lichteck auf
Objekt / Kante sichtbar.
Im Reektor-Mode sind transparente und nicht-transparente Objekte
detektierbar.
Mode-Wahl:
Während Neustart. Reektor im Lichtfeld positionieren.
2b Reektor 5° ... 10° bezogen auf Sensor neigen. Für optimalen
Lichtempfang Objekt und Reektor laut Tabelle positionieren:
Typ Max. Abstand
Reektor
Abstand transparentes
Objekt
NM111 / PM111 60 mm 22 ... 26 mm
NM331 / PM331 200 mm 90 ... 110 mm
3 Analogausgang Q
A
:
Analogausgang Q
A
(messend) gibt die „Position der ersten Kontrast-
kante im Messbereich, bezogen auf die Steckerseite”, aus:
Schaltausgang Q
P
/ Q
N
(schaltend / Plausibilität):
Q
P
/ Q
N
Schaltausgangsanzeige
(gelbe LED)
High O / E im Messbereich an
Low O / E nicht im Messbereich aus
4
Objektposition O /
Kantenposition E
TW 100 mm
Objektposition O /
Kantenposition E
TW 25 mm
Analogausgang Q
A
0 mm 0 mm 4 mA
30 mm 20 mm 20 mA
15 mm 10 mm 12 mA
Zielregelgröße
< 0 mm < 0 mm 3.5 mA, O / E läuft
zur Steckerseite aus
> 30 mm > 20 mm 20.5 mA, O / E läuft
zur Kopfseite aus
keine Kante im
Messfeld
keine Kante im
Messfeld
3 mA
5 Sensor erkennt Kontrastsprung von Schwarz auf Weiß.
6 Messbereich / Tastweite [TW]:
Nur AT20E_ _111: bezogen auf 50% Kontrast zu weißem Papier.
Nur AT20E_ _331: bezogen auf 30% Kontrast zu weißem Papier.
(typische Werte)
Wartung
SICK-Sensoren sind wartungsfrei.
Wir empfehlen, in regelmäßigen Abständen
- die optischen Grenzächen zu reinigen
- Verschraubungen und Steckverbindungen zu überprüfen
Veränderungen an Geräten dürfen nicht vorgenommen werden.
Irrtümer und Änderungen vorbehalten. Angegebene Produkteigenschaften
und technische Daten stellen keine Garantieerklärung dar.
AT20E -PM111 -NM111 -PM331 -NM331
Scanning range (TW) Tastweite (TW) Distance de détection (TW) Distância de detecção (TW) 25 mm 25 mm 100 mm 100 mm
Measuring range Messbereich Plage de mesure Faixa de medição 20 mm 20 mm 30 mm 30 mm
Light spot Lichtfleck Spot lumineux Ponto de luz 30 mm x 5 mm
2
30 mm x 5 mm
2
50 mm x 10 mm
2
50 mm x 10 mm
2
Supply voltage U
B
Versorgungsspannung U
B
Tension d'alimentation U
B
Tensão de alimentação U
B
DC 24 V ± 20%
1)
DC 24 V ± 20%
1)
DC 24 V ± 20%
1)
DC 24 V ± 20%
1)
Switching output Schaltausgang Sortie de commutation Saída de comutação PNP NPN PNP NPN
Max. output current Q
P
/ Q
N
Max. Ausgangsstrom Q
P
/ Q
N
Courant de sortie max. Q
P
/ Q
N
Corrente de saída máx. Q
P
/ Q
N
100 mA 100 mA 100 mA 100 mA
Analog output Q
A
Analogausgang Q
A
Sortie analogique Q
A
Saída analógica Q
A
4 ... 20 mA
2)
4 ... 20 mA
2)
4 ... 20 mA
2)
4 ... 20 mA
2)
Response time Q
P
/ Q
N
Ansprechzeit Q
P
/ Q
N
Temps de réponse Q
P
/ Q
N
Tempo de resposta Q
P
/ Q
N
3 ms
3)
3 ms
3)
3 ms
3)
3 ms
3)
Output rate Ausgaberate Débit de sortie Taxa de saída 1 ms 1 ms 1 ms 1 ms
Reproducibility Reproduzierbarkeit Reproductibilité Reprodutibilidade 30 µm 30 µm 50 µm 50 µm
Enclosure rating Schutzart Type de protection Grau de proteção IP 67 IP 67 IP 67 IP 67
Protection class Schutzklasse Classe de protection Classe de proteção
Ambient operating temperature Betriebsumgebungstemperatur Température ambiante Temperatura do ambiente operacional –10 °C ... +55 °C –10 °C ... +55 °C –10 °C ... +55 °C –10 °C ... +55 °C
1)
Limit values
residual ripple max. 5 Vss
U
B
connections reverse polarity protected
2)
Nominal load residue R
L
= 500 Ω
3)
Minimale response time
1)
Grenzwerte
Restwelligkeit max. 5 Vss
U
B
-Anschlüsse verpolsicher
2)
Nennlastwiderstand R
L
= 500 Ω
3)
Minimale Ansprechzeit
1)
Valeurs limites
ondulation résiduelle max. 5 Vcc
Raccordements U
B
protégés contre les inversions de polarité
2)
Résistance de charge nominale R
L
= 500 Ω
3)
Temps de réponse minimal
1)
Valores limite
ondulação residual máx. 5 Vss
Conexões U
B
protegidas contra inversão de polos
2)
Resistência nominal de carga R
L
= 500 Ω
3)
Tempo de resposta mínimo
AT20E -PM111 -NM111 -PM331 -NM331
Distanza di tastatura (TW)
Distancia de detección (TW)
扫描距离(TW
スキャン幅 (TW)
Область сканирования (TW) 25 mm 25 mm 100 mm 100 mm
Campo di misura
Campo de medición
测量范围
測定範囲
Диапазон измерения 20 mm 20 mm 30 mm 30 mm
Punto luminoso
Spot
光点
光軸スポット
световое пятно 30 mm x 5 mm
2
30 mm x 5 mm
2
50 mm x 10 mm
2
50 mm x 10 mm
2
Tensione di alimentazione U
B
Tensión de alimentación U
B
电源电压 U
B
供給電圧 U
B
Напряжение питания U
B
DC 24 V ± 20%
1)
DC 24 V ± 20%
1)
DC 24 V ± 20%
1)
DC 24 V ± 20%
1)
Uscita di commutazione
Salida conmutada
开关量输出
スイッチング出力
Переключающий выход PNP NPN PNP NPN
Corrente in uscita max. Q
P
/ Q
N
Intensidad máx. de salida Q
P
/ Q
N
最大输出电流 Q
P
/ Q
N
最大出力電流 Q
P
/ Q
N
Макс. выходной ток Q
P
/ Q
N
100 mA 100 mA 100 mA 100 mA
Uscita analogica Q
A
Salida analógica Q
A
模拟输出端 Q
A
アナログ出力 Q
A
Аналоговый выход Q
A
4 ... 20 mA
2)
4 ... 20 mA
2)
4 ... 20 mA
2)
4 ... 20 mA
2)
Tempo di risposta Q
P
/ Q
N
Tiempo de respuesta Q
P
/ Q
N
触发时间 Q
P
/ Q
N
応答時間 Q
P
/ Q
N
Время отклика Q
P
/ Q
N
3 ms
3)
3 ms
3)
3 ms
3)
3 ms
3)
Frequenza di uscita
Velocidad de salida
输出率
出力レート
Производительность 1 ms 1 ms 1 ms 1 ms
Riproducibilità
Reproducibilidad
再现性
再現性
Воспроизводимость 30 µm 30 µm 50 µm 50 µm
Tipo di protezione
Tipo de protección
保护种类
保護等級
Степень защиты IP 67 IP 67 IP 67 IP 67
Classe di protezione
Clase de protección
保护级别
保護クラス
Класс защиты
Temperatura ambiente circostante
Temperatura ambiente de servicio
工作环境-温度
動作周囲温度
Диапазон рабочих температур –10 °C ... +55 °C –10 °C ... +55 °C –10 °C ... +55 °C –10 °C ... +55 °C
1)
Valori limite ondulazione
ondulazione residua max. 5 Vss
U
B
-collegamenti con protez contro inversione di poli
2)
Resistenza nominale R
L
= 500 Ω
3)
Tempo di risposta minimo
1)
Valores límite
ondulación residual máx. 5 Vss
Conexiones U
B
a prueba de inversión de polaridad
2)
Resistencia de carga nominal R
L
= 500 Ω
3)
Tiempo de respuesta mínimo
1)
极限值剩余波
最大余波 5 Vss
U
B
-接头防反接
2)
额定负载电阻 R
L
= 500 Ω
3)
最短响应时间
1)
限界値
残留リップルは最大 5 Vss
U
B
コネクタ 逆接保護
2)
定格負荷抵抗 R
L
= 500 Ω
3)
最小応答時間
1)
Пределы
Остаточная пульсация макс. 5 Vss
U
B
-подключения с защитой от перепутывания полюсов
2)
Номинальное сопротивление нагрузки R
L
= 500 Ω
3)
Минимальное время отклика
All dimensions in mm
(inch)
48.6 (1.91)
14.2
(0.56)
50.2
(1.98)
Ø 4.5
(0.18)
4.5
(0.18)
4.5
(0.18)
4.2
(0.17)
13.1
(0.51)
59.8
(2.35)
42.9
(1.69)
24.0
(0.94)
24.3
(0.96)
54.1
(2.13)
L+
Q
M
NC
Q
A
1
4
2
brn
blk
wht
3
blu
5
gra
SK
1b
2b
5-1
5-
10°
5-10
°
5-10°
5-10°
3
4
5
6
O/E [mm]
2010
(30) (15)
0
20.5
20
4
3.5
12
Q
A
[mA]
S
K
Q
P
/Q
N
H
L
20.5 mA
3.5 mA
4 mA
12 mA
20 mA
Sensor
Sensor
TW mm (inch)
20
(0.79)
18
(0.71)
AT20E__111:
A
T20E__331:
20
(0.79)
22
(0.87)
25
(0.98)
30
(1.18)
28
(1.10)
30
(1.18)
32
(1.26)
90
(3.54)
100
(3.94)
110
(4.33)
TW mm (inch)
1 / 1

SICK SENSICK AT20E EDGE/PROXIMITY Operating instructions

Category
Convenience lighting
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document