Sony MDR-IF140K Owner's manual

Cordless Stereo

Headphone

System

Operating Instructions

Bedienungsanleitung

Инструкция по эксплуатации

3-248-366-46(1)

MDR-IF140K

DE

RU

GB

2

GB

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To prevent fire or shock hazard, do not

place objects filled with liquids, such as

vases, on the apparatus.

To avoid electrical shock, do not open

the cabinet. Refer servicing to qualified

personnel only.

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

Owner’s Record

The model number is located on the top

of the transmitter and the left inner side

of the headband.

The serial number is located at the

bottom of the transmitter and the right

inner side of headband.

Record these numbers in the spaces

provided below. Refer to them

whenever you call upon your Sony

dealer regarding this product.

Model No. MDR-IF140K

Transmitter TMR-IF130

Headphones MDR-IF140

Serial No.

Transmitter

Headphones

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The validity of the CE marking is restricted

to only those countries where it is legally

enforced, mainly in the countries EEA

(European Economic Area).

Disposal of Old

Electrical &

Electronic

Equipment

(Applicable in the

European Union

and other European

countries with

separate collection

systems)

This symbol on the product or on its

packaging indicates that this product

shall not be treated as household waste.

Instead it shall be handed over to the

applicable collection point for the

recycling of electrical and electronic

equipment. By ensuring this product is

disposed of correctly, you will help

prevent potential negative

consequences for the environment and

human health, which could otherwise

be caused by inappropriate waste

handling of this product. The recycling

of materials will help to conserve

natural resources. For more detailed

information about recycling of this

product, please contact your local city

office, your household waste disposal

service or the shop where you

purchased the product.

3

GB

Welcome!

Thank you for purchasing the Sony

MDR-IF140K Cordless Stereo

Headphone System. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

The MDR-IF140K is a cordless stereo

headphone system using infrared

transmission. You can enjoy listening to

a program free from the restriction of

the headphone cord by simply

connecting the transmitter to a TV, or

audio components equipped with a

headphone jack or a line output jack.

• Cordless, noiseless infrared headphone

system resistant to external noise, etc.

• Wide infrared reception range of up to 7m

(23 ft.).

• Self-adjusting headband mechanism

eliminating the need for headband

adjustment.

• Single VOL control adjusts both the right

and left volume of the headphones.

Table of contents

Getting started

Unpacking ........................................... 4

Inserting the battery .......................... 5

Setting up the transmitter ................. 6

Operating the system

Listening to a program ...................... 8

The effective area of the

transmitter ..................................... 10

Replacing the ear pads .................... 10

Additional information

Specifications .................................... 11

Precautions ....................................... 12

Troubleshooting ............................... 13

GB

Getting started

4

GB

N Getting started

Unpacking

Check that you have the following

items before using the headphones:

• The transmitter TMR-IF130 (1)

• AC power adaptor (1)

• Connecting cord (1)

(phono plugs h stereo mini plug)

• Unimatch plug adaptor (1)

(stereo mini jack h stereo phone

plug)

• The headphones MDR-IF140 (1)

Getting started

5

GB

Inserting the

battery

1 Open the battery compartment

lid of the left housing.

2 Insert the size AAA dry battery

into the battery compartment

matching 3 terminal on the

battery to 3 in the

compartment.

3 Close the battery compartment

lid.

Battery life

*

1

at 1 kHz, 1 mW+1 mW output

*

2

Time stated above may vary, depending

on the temperature or conditions of use.

Notes on Batteries

• Do not charge a dry battery.

• Do not carry a dry battery together

with coins or other metallic objects. It

can generate heat if the positive and

negative terminals of the battery are

accidentally come into contact with

metallic objects.

• When you are not going to use the

unit for a long time, remove the

battery to avoid damage from battery

leakage or corrosion.

When to replace the battery

When the battery becomes weak, the

power indicator light dims, or sound

becomes distorted or noisy. Replace the

battery with new one as soon as

possible.

Battery

Sony alkaline

battery LR03/

AM-4(N)

Sony manganese

battery R03/UM-4

(NU)

Approx. hours*

1

60 hours*

2

28 hours*

2

Getting started

6

GB

RLINE IN

DC IN 9V

L

PHONES IN

Setting up the

transmitter

The transmitter is equipped with two

input jacks, which allows for connection

to the specified output jacks: PHONES

IN to the headphone jack, and LINE IN

to the LINE OUT jacks of your

connected equipment.

1 Connect the transmitter to an

audio/video component.

Select method A or B, according

to the output jack type of the AV

component you use.

* WALKMAN is a registered trademark of

Sony Corporation to represent Headphone

Stereo products.

Transmitter

Unimatch plug

adaptor (supplied)

WALKMAN*, TV,

VCR, etc.

A When connecting to a

headphones jack

Connect to the PNONES IN jack on

the transmitter.

Connecting cord

(supplied)

to PHONES IN jacks

to headphone jack

(stereo mini jack)

to headphone jack

(stereo phone jack)

Left channel

(white)

Right channel

(red)

Getting started

7

GB

Note

If your AV component has a stereo mini jack

(LINE OUT), connect the stereo mini jack to

LINE IN jack of the transmitter by using the

connecting cord RK-G136 sold separately. If

you connect LINE OUT jack of your AV

component to PHONES IN jack of the

transmitter, volume may be too low.

B When connecting to any jacks

other than the headphones jack

Connect to the LINE IN jacks on the

transmitter.

2 Connect the transmitter to the

power source.

(Continued)

RLINE IN

DC IN 9V

L

PHONES IN

Transmitter

to LINE IN jack

Right channel

(red)

Left channel

(white)

to any jacks other

than headphone jack

Connecting cord

(supplied)

Stereo, TV, VCR, etc.

RLINE IN

DC IN 9V

L

PHONES IN

to DC IN 9

V jack

Transmitter

to an AC

outlet

AC power

adaptor

(supplied)

Operating the system

8

GB

N Operating the system

Listening to a

program

Before listening

To prevent your ears from being

damaged, first lower the volume.

1 Turn on the audio/video

component connected to the

transmitter.

When the audio signal is input, the

transmitter turns on automatically

and the infrared emitters glow. If

the transmitter is connected to the

headphone jack, set the volume

control of the audio source

component as high as possible but

not so high that the audio signal

becomes distorted.

2 Turn on the headphones.

The power indicator on the upper

part of the right housing glows red.

3 Put on the headphones.

Be sure to put the right housing (R)

on your right ear and the left

housing (L) on your left ear.

Notes

•Do not connect to the PHONES IN jack and

LINE IN jack at the same time. If you

connect two audio/visual components to

both jacks at the same time, both of the

audio signals may result in mixed output.

•Use only the supplied AC power adaptor.

Do not use any other AC power adaptor.

•When you connect the connecting cord

directly to an earphone jack (monaural

mini jack), the audio signal may not be

output through the right channel. In such a

case, use the separately sold PC-236MS

plug adaptor (stereo mini jack h

monaural mini plug) between the

connecting cord and the earphone jack.

Unified

polarity plug

Operating the system

9

GB

4 Start playback of the

component connected to the

transmitter.

5 Adjust the volume.

If the infrared sensors are covered

by your hands when adjusting the

volume, the mute function will be

activated and volume may not be

adjusted. In this case, move nearer

toward the transmitter or orient the

infrared emitters on the left housing

towards the transmitter.

After listening to the programs

Take off the headphones, and then turn

off the power.

Note

You may hear some noise when you

disconnect the AC power adaptor from the

transmitter before taking off the headphones.

Sound is automatically muted if

noise increases

— Mute function

If the infrared rays are obstructed, or

the headphones are used outside their

effective range, noise will increase and

sound will become hard to hear. To

avoid potential ear damage as a result

of noise, this function mute any sound

from the headphones. Sound is

automatically restored when you move

nearer the transmitter or remove the

obstruction.

If no audio signal is input for

more than approximately 5

minutes

The transmitter turns off automatically.

Note

The brightness of the infrared emitters may

not be uniform, however, this is not a

malfunction.

Operating the system

10

GB

The effective area

of the transmitter

The illustration below shows the

approximate area covered by the

infrared rays emitted from the

transmitter.

Notes

• If you use the headphones at too great a

distance from the transmitter, you may

hear a hissing noise and if there is an

object between the headphones and the

transmitter, sound may be interrupted.

These phenomena are inherent to infrared

ray communication and do not mean that

there is a problem with the system itself.

• Do not cover the infrared sensors with

your hands or hair.

• When you use the headphones inside the

area in the illustration above, the

transmitter can be placed in front, behind

or by the side of you.

• The noise you may hear through the

headphones may vary depending on the

transmitter position and room conditions.

It is recommended that you place the

transmitter in a location that produces the

clearest sound.

• Do not use this system in areas exposed to

direct sunlight or strong light. The sound

may be interrupted.

• Plasma displays may interfere with normal

operation of this system.

45°

Transmitter

Infrared ray

Approx. 3 m

(118

1

/

8

in.)

Approx. 3 m

(118

1

/8 in.)

Approx. 7 m

(23 ft.)

Replacing the ear

pads

The ear pads are replaceable. If the ear

pads become dirty or worn out, replace

them as illustrated below.

The ear pad is not commercially

available. You can order replacements

from the store where you purchased

this system, or at your nearest Sony

dealer.

1 Remove the old ear pad by

pulling it off.

2 Place the new ear pad around

the housing.

Additional information

11

GB

N

Additional information

Specifications

General

Modulation system

Frequency modulation

Carrier frequency

Right 2.8 MHz

Left 2.3 MHz

Frequency response

18 – 22,000 Hz

Transmitter TMR-IF130

Power source DC IN 9 V jack accepts

power supplied from the AC

power adaptor for use on the

following voltages:

Audio input Phono jacks/stereo mini jack

Dimensions Approx. 152 × 38 × 72 mm

(6 × 1

1

/2 × 2

3

/4 in.)

(w/h/d)

Mass Approx. 75 g (2.7 oz.)

Headphone MDR-IF140

Power source Dry battery (size AAA)

Mass Approx. 125 g (4.41 oz.)

including battery

Supplied accessories

AC power adaptor (1)

Connecting cord (approx. 1m, stereo mini

plug × 1 y phono plug × 2) (1)

Unimatch plug adaptor (stereo mini jack

y stereo phone plug) (1)

Operating instructions (1)

Optional accessories

• If you connect with a stereo mini jack

(LINE OUT )

RK-G136

(1.5 m, stereo mini plug × 1 y stereo

mini plug × 1)

• If sound is not output through the right

channel when the supplied connecting

cord is connected to the earphone jack.

Plug adaptor PC-236MS

(stereo mini jack y monaural mini

plug)

• If you have lost the supplied plug

adaptor.

Plug adaptor PC-234S

(stereo mini jack y stereo phone plug)

• If you have lost the supplied connecting

cord.

RK-G129

(1.5 m, stereo mini plug y phono plug

× 2)

Design and specifications are subject to

change without notice.

Where

purchased

U.S.A.

U.K.

European countries

Japan (except for

Japanese domesitic

model)

Other countries

Operating

voltage

120 V AC, 60 Hz

230 V AC, 50 Hz

110 V/120 V/220 V/

240 V AC, 50/60 Hz

220 – 230 V AC, 50/60

Hz or 120 V AC, 60 Hz

Additional information

12

GB

Precautions

• When the transmitter is not to be

used for a long period of time,

disconnect the AC power adaptor

from the AC outlet holding the plug

and remove the battery to avoid

damage caused by battery leakage

and subsequent corrosion.

• Do not leave the cordless stereo

headphones system in a location

subject to direct sunlight, heat or

moisture (It is recommended to use

the headphones at a temperature of

between 5˚C and 35˚C (between 41˚F

and 104˚F).)

• Do not drop, hit or otherwise subject

the transmitter or headphones to

strong shocks of any kind. This could

damage the product.

Notes on headphones

preventing hearing damage

Avoid using headphones at high

volume. Hearing experts advise against

continuous, loud and extended play. If

you experience a ringing in your ears,

lower the volume or discontinue use.

Caring for others

Keep the volume at a moderate level.

This will allow you to hear outside

sounds and to be considerate to the

people around you.

If you have any questions or problems

concerning the system that are not

covered in this manual, please consult

nearest Sony dealer.

Be sure to bring the headphones and

the transmitter to Sony dealer when

requiring repair work.

Additional information

13

GB

, If you connect the headphone jacks of

your connected equipment to the LINE

IN jack of the transmitter, sound may

be distorted when raising the volume.

Use the PHONES IN jacks of the

transmitter instead. See “Setting up the

transmitter.”

Loud background noise

, Move closer to the transmitter. (As you

move away from the transmitter, more

noise is likely to be heard. This is

inherent in infrared ray communication

and does not mean that there is a

problem with the unit itself.)

, Check that there is no object between

the transmitter and the headphones.

, Check that the infrared sensors are not

covered with your hands or hair.

, If you use the headphones by a

window where the sunlight is too

strong, draw the curtains/blinds to

shut out the direct sunlight, or use the

headphones away from the sunlight.

, Change the position or angle of the

transmitter.

, If the transmitter is connected to the

headphones jack, raise the volume of

the audio/video equipment connected

to the transmitter.

, The headphones’ power indicator light

dims, flashes or goes off.

• Replace dry battery with new one. If

the power indicator is still off after

replacing the battery, take the

headphones to a Sony dealer.

, When you have another transmitter,

check if more than one transmitters are

used at the same time.

• Turn off other transmitter or move to

a place outside the range of this

transmitter.

Troubleshooting

No sound/Muffled sound

, Turn on the transmitter first, and then

put on the headphones.

, Check the connection of the audio/

video equipment or the AC power

adaptor.

, Check that the audio/video equipment

connected to the transmitter is turned

on.

, If the transmitter is connected to the

headphones jack, raise the volume of

the audio/video equipment connected

to the transmitter.

, The mute function is activated.

• Check if there is any object between

the transmitter and the headphones.

• Use the headphones near the

transmitter.

• Change the position and angle of the

transmitter.

, The headphones’ power indicator light

dims, flashes or goes off.

• Replace dry battery with new one. If

the power indicator is still off after

replacing the battery, take the

headphones to a Sony dealer.

, If you connect the LINE OUT jacks of

your connected equipment to the

PHONES IN jacks of the transmitter,

volume may be too low. Use the LINE

IN jacks of the transmitter instead. See

“Setting up the transmitter.”

Distorted sound

, If the transmitter is connected to the

headphones jack, lower the volume of

the audio/video equipment connected

to the transmitter.

, The headphones’ power indicator light

dims, flashes or goes off.

• Replace dry battery with new one. If

the power indicator is still off after

replacing the battery, take the

headphones to a Sony dealer.

Page is loading ...

Printed in Malaysia

Sony MDR-IF140K Owner's manual

Sony MDR-IF140K Owner's manual

in other languages

Related papers

Other documents