Craftsman 580.75201 User manual

Brand: Craftsman

Model: 580.75201

Category: High-pressure cleaners

Type: User manual

This manual is also suitable for

580752010

Owner's Manual

4.0 HORSEPOWER

2150 PSi

1.9 GPM

Model No. 580.752010

CAUTION

Before using this product, read this

manual and follow all Safety Rules and

Operating instructions.

PRECAUCtON

Antes de utilizar el producto, lea este

manual y siga todas las Reglas de

Seguridad e Instrucciones de Uso.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: wv_w.craftsmamcom

o Safety

o Assembly

o Operation

o Maintenance

o Parts

o EspaSoN

0 1

Part No. 195927GS Draft 2 (02/18/2005)

WARRANTY .................................... 2

SAFETY RULES ............................... 2-4

FEATURES & CONTROLS ......................... 5

ASSEMBLY ................................... 6-7

OPERATION ................................. 8-11

SPECIFICATIONS ............................... 12

MAINTENANCE .............................. 13-16

STORAGE .................................. 17-18

TROUBLESHOOTING ............................ 19

REPLACEMENT PARTS ....................... 20-24

NOTES ....................................... 25

EMISSION CONTROL WARRANTY .............. 26-27

ESPAI_OL ................................... 28-47

HOW TO ORDER PARTS ................ BACK PAGE

LIMITED WARRANTY ON CRAFTSMAN PRESSURE WASHER

For one year from the date of purchase, when this Craftsman pressure washer is maintained and operated

according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and

workmanship.

if this washer is used for commercial purposes, this warranty applies for only 90 days from the date of

purchase. If this pressure washer is used for rental purposes, this warranty applies for only 30 days after date

of purchase.

This warranty does not cover:

• Expendable items such as spark plugs or air filters, which become worn during normal use.

• Repairs necessary because of operator abuse or negligence, including damage resulting from no water

being supplied to pump or failure to maintain the equipment according to the instructions contained in the

owner's manual.

Warranty service is available by returning the pressure washer to the nearest Sears service center or dealer in

the United States.

This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

This is the safety alert symbol it is used to alert you to potentiam personam injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

,r'Y I_Read this manuam carefully and become

i__ AI....: familiar with your pressure washer. Know its

applications, its limitations, and any hazards

involved.

The safety alert symbol (_&) is used with a signal

word (DANGER, CAUTION, WARNING), a pictorial

and/or a safety message to alert you to hazards.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury. WARNING indicates a

hazard which, if not avoided, could result in death or

serious injury. CAUTION indicates a hazard which, if

not avoided, might result in minor or moderate injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in equipment

damage. Follow safety messages to avoid or reduce

the risk of injury or death.

Hazard Symbols and Meanings

Toxic Fumes

Slippery Surface

Fire

Fal!

Electrical Shock

Fluid Injection

Exp!osion Hot Surface

Moving Parts Flying Objects

Kickback

WARNtNG

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Operate pressure washer ONLY outdoors.

Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

DO NOT operate pressure washer inside any building or

enclosure.

Use a respirator or mask whenever there is a chance

that vapors may be inhaled.

Read all instructions packed with mask so you are certain

mask will provide necessary protection against inhaling

harmful vapors.

WARNING

Keep spray nozzle between 8 to 24 inches away from

cleaning surface.

Operate this unit on a stable surface.

Cleaning area should have adequate slopes and

drainage to reduce possibility of falls due to slippery

surfaces.

Be extremely careful if you must use pressure washer

from a ladder, scaffolding or any other relatively unstable

location.

Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun kicks back.

WARNING

When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze

trigger on spray gun.

WARNING

WHEN ADDING OR DRAINBNG FUEL

Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

Fil! or drain fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel expansion.

Keep fue! away from sparks, open flames, pilot lights,

heat, and other ignition sources.

DO NOT light a cigarette or smoke.

VHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap and air cleaner are

in place.

DO NOT crank engine with spark plug removed.

If fuel spills, wait until it evaporates before starting

engine.

VHEN OPERATmNG EQUIPMENT

* Do not tip engine or equipment at angle which causes

fuel to spill.

DO NOT spray flammable liquids,

WHEN TRANSPORTING OR REPAIRBNG EQUIPMENT

Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

Disconnect spark plug wire.

WHEN STORING FUEL OR EQUBPMENT WITH FUEL mN

TANK

Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fue! vapors.

WARN NG

NEVER aim spray gun at people, animals or plants.

DO NOT allow CHILDREN to operate pressure washer.

NEVER repair high pressure hose. Replace it.

NEVER repair leaking connections with sealant of any

kind. Replace ooring or seal.

Keep high pressure hose connected to pump and spray

gun while system is pressurized.

Squeeze trigger on spray gun to relieve trapped

pressure, every time you stop engine. Engage trigger

lock on spray gun.

WARNING 1

• Keep water spray away from electric wiring or fatal

electric shock may result.

WARNING

DO NOT touch hot surfaces.

Allow equipment to cool before touchin%

The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

WARNING

• DO NOT wear loose clothing, jewelry or anything that

may be caught in starter or other rotating parts.

• Tie up long hair and remove jewelry.

WARNING

WHEN ADJUSTING OR MAKmNG REPAIRS TO YOUR

PRESSURE WASHER

Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

DO NOT check for spark with spark plug removed.

WARNING

Always wear eye protection when using equipment or when

in vicinity of equipment in use.

CAUTION

DO NOT tamper with governed speed.

DO NOT operate pressure washer above rated pressure.

CAUTION

DO NOT secure spray gun in open position.

DO NOT leave spray gun unattended while machine is

running.

NEVER use a spray gun which does not have a trigger

lock or trigger guard in place and in working order.

Always be certain spray gun, nozzles and accessories

are correctly attached.

CAUTION

DO NOT point spray gun at glass when in jet spray mode.

NEVER aim spray gun at plants.

CAUTION

If you have questions about intended use, ask dealer or

contact Sears.

NEVER operate units with broken or missing parts, or

without protective housing or covers.

DO NOT by-pass any safety device on this machine.

Before starting pressure washer in cold weather, check

all parts of the equipment to be sure ice has not formed

there.

NEVER move machine by pulling on high pressure hose.

Use handle provided on unit.

Check fuel system for leaks or signs of deterioration,

such as chafed or spongy hose, loose or missing

clamps, or damaged tank or cap. Correct all defects

before operating pressure washer.

This equipment is designed to be used with Sears

authorized parts ONLY. If equipment is used with parts

that DO NOT comply with minimum specifications, user

assumes al! risks and liabilities.

KNOW YOUR PRESSURE WASHER

Read the owner's manual and safety rubes before operating your pressure washer,

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

Recoil Starter

Air Cleaner

Throttle Control

Lever

Oil Fill Cap and Dipstick

Detergent Pick-Up

Tube and Filter

Primer Bulb

Fuel Cap

Air Filter -- Protects engine by filtering dust and

debris out of intake air.

Automatic Cool Down System -- Cycles water

through pump when water reaches 125°z155°F. Warm

water wHmdischarge from pump onto ground. TMs

system prevents interna! pump damage.

Detergent Pick-Up Tube and Filter = Used to siphon

detergent from chemical bottle to the low pressure

water stream.

Fuel Cap = Fill fuel tank with regular unleaded fuel here.

High Pressure Hose (not shown) - Connect one end

to the spray gun and other end to the high pressure

outlet.

High Pressure Outlet -- Connection for high pressure

hose.

Nozzle Extension with Quick Connect (not shown)

-- Allows you to switch between four different nozzles.

Water inlet

High Pressure Outlet

Pump equipped with

Automatic Cool Down System

Oil Fitl Cap and Dipstick - Check and fill engine with

oil here. See page 6 for oil recommendations and

filling instructions.

Primer Bulb -- Prepares a cold engine for starting.

Pump -- Develops high water pressure.

RecoimStarter -- Used for starting the engine

manually.

Spray Gun (not shown} - Controls the application of

water onto cleaning surface with trigger device.

includes trigger lock.

Spray Tips (not shown} -- Chemical injection, 0%

15°, and 40°: for various high pressure cleaning

applications.

Throttle Control Lever - Sets engine in starting

mode for recoil starter and stops running engine.

Water inlet -- Connection for garden hose.

Yourpressurewasherrequiressomeassemblyandis

readyforuseonlyafterithasbeenproperlyserviced

withtherecommendedoilandfuel.

Ifyouhaveanyproblemswith theassemblyof

your pressurewasher,pleasecallthepressure

washerhelplineat 1-800-222-3136.

IMPORTANT:Anyattempttoruntheenginebeforeit

hasbeenservicedwiththerecommendedoilwillresult

in an engine failure.

NOTE: When adding oil to the engine crankcase, use

only high quality detergent oil rated with API service

classification SF, SG, SH, SJ or higher. DO NOT use

special additives.

1. Choose a viscosity according to the following table.

REMOVE PRESSURE WASHER

FROM CARTON

• Open carton and slice two corners from top to

bottom so the panel can be folded down flat.

• Remove fillers, accessories and parts bag shipped

with your pressure washer.

• Remove the pressure washer out the open end of

the carton.

• Check carton for additional loose parts.

CARTON CONTENTS

Check all contents. If any parts are missing or damaged,

call the pressure washer helpline at 1-800-222-3136.

• The main unit

• High pressure hose

• Spray gun

• Nozzle extension with quick connect fitting and

nozzle holder

• Safety goggles

• Engine oil

• Parts bag (which includes items listed below)

Owner's manual

Registration card

Bag containing 4 multi=colored spray tips

Become familiar with each piece before assembling

the pressure washer. Compare contents against the

view on page 5. If any parts are missing or damaged,

call the pressure washer helpline at 1-800-222-3136.

ASSEMBLING YOUR PRESSURE

WASHER

Your Craftsman pressure washer was mostly assembled

at the factory. However, you will need to perform these

tasks before you can operate your pressure washer:

1. Add oil to engine crankcase.

2. Add fuel to fuel tank.

3. Connect high pressure hose to spray gun and pump.

4. Connect water supply to pump.

5. Select/attach quick connect spray tip to nozzle

extension.

Add Engine Oil

IMPORTANT: Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine failure.

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

* The use of multi-viscosity oils (5W-30, 10W-30, etc.)

in temperatures above 40°F (4°C) will result in higher

than normal oil consumption. When using a multi-

viscosity oil, check oil more frequently.

** If using SAE 30 oil in temperatures below 40°F

(4°C), it will result in hard starting and possible

engine bore damage due to inadequate lubrication.

2. Place pressure washer on a level surface and

clean area around oil fill.

3. Remove dipstick and wipe clean with cloth.

4. Replace and tighten dipstick.Remove and check oil

level.

5. Slowly pour oil into oil fill opening. Pause to permit

oil to settle. Fill to "Full" mark on dipstick. DO NOT

OVERFILL. Remove dipstick and check oil level.

NOTE: You may not need to use all the supplied oil.

6. Replace dipstick and tighten securely.

NOTE: Check oil often during engine break=in.

Add Fuel

WARNING

WHEN ADDING FUEL

Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

Fil! or drain fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel expansion.

Keep fue! away from sparks, open flames, pilot lights,

heat, and other ignition sources.

DO NOT light a cigarette or smoke.

NOTE: This engine is certified to operate on gasoline.

Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a

minimum of 77 octane with equipment. DO NOT

use fuel which contains Methanol. DO NOT mix oil

with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be

careful not to overfill. Allow about 1.5" of tank

space for fuel expansion, as shown here.

4. install fuel cap and wipe up any spilled fuel.

CAUTRON! Alcohol-blended fuels (called gasohol,

ethanol or methanol) can attract moisture, which leads

to separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage.

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. Drain the

fuel tank, start the engine and let it run untiJthe fuel lines

and carburetor are empty. Use fresh fuel next season.

See "Storage" on pages 17-18 for additional information.

NEVER use engine or carburetor cleaner products in

the fuel tank as permanent damage may occur.

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must

assemble the nozzle extension to the spray gun and

attach all hoses before you start the engine.

1. Uncoil high pressure hose and attach one end of

hose to base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high

pressure outlet on pump. Tighten by hand.

Before connecting garden hose to water inlet,

inspect inlet screen. Clean screen if it contains

debris or have it replaced if damaged. Refer to

section "O-Ring Maintenance" if inlet screen is

damaged. DO NOT run pressure washer if inlet

screen is damaged.

"_ __ Inspect inlet

-_,. screen. DO

NOT use if

damaged;

clean if dirty.

4. Run water through garden hose for 30 seconds to

flush it of debris. Turn off water.

IMPORTANT: DO NOT siphon standing water for the

water supply. Use ONLY cold water (less than 100°F).

5. Connect garden hose (not to exceed 50 feet in

length) to water inlet. Tighten by hand.

CAUTION

* Damage to equipment resulting from failure to follow

this instruction will void warranty,

6. Turn ON water and squeeze trigger on spray gun

to purge pump system of air and impurities.

WARNING

Always wear eye protection when using this equipment

or in vicinity of where equipment is in use.

Before starting the pressure washer, be sure you are

wearing adequate eye protection,

Checklist Before Starting Engine

Review the unit to ensure you have performed all of

the following:

1. Check that oil has been added to proper level in

engine crankcase.

2. Add proper gasoline to fuel tank.

3. Check for properly tightened hose connections

(high pressure and water supply) and that there

are no kinks, cuts, or damage to high pressure

hose.

4. Provide proper water supply (not to exceed

100 °F).

5. Be sure to read "Safety Rules" and "Operation"

sections before using the pressure washer.

6. If starting unit after storage, see "Storage" section

on pages 17-18.

HOW TO USE YOUR PRESSURE

WASHER

if you have any problems operating your pressure

washer, please call the pressure washer helpline at

1-800-222-3136.

Pressure Washer Location

Pressure Washer Clearance

WARNING

Operate pressure washer ONLY outdoors,

Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings,

DO NOT operate pressure washer inside any building or

enclosure,

The pressure washer must be at least 5 ft. (152 cm)

from structures having combustible walls and/or other

combustible materials. Leave at least 3 ft. (92 cm) all

around pressure washer including overhead, for

adequate cooling, maintenance and servicing.

Place pressure washer in a well ventilated area, which

will allow for removal of deadly exhaust gas. DO NOT

place pressure washer where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is

kept away from any windows, doors, ventilation

intakes or other openings that can allow exhaust gas

to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when

positioning pressure washer.

To Start Your Pressure Washer

To start your engine-powered pressure washer for the

first time, follow these instructions step-by-step. This

starting information also applies whenever you start

the engine after you have let the pressure washer sit

idle for at least a day.

1. Place pressure washer near an outside water

source capable of supplying water at a flow rate

greater than 2.9 gallons per minute and no less than

20 PSI at pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected

to spray gun and pump. See "Assembling Your

Pressure Washer" for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

CAUTION

• Damage to equipment will result from failure to follow

this instruction.

5. Squeeze trigger on gun to purge pump system of

air and impurities.

6. Place colored quick connect spray tips in slots on

holder that's attached to nozzle extension.

7. Attach nozzle extension to spray gun. Tighten by

hand.

Typical Pressure

Washer Shown

Exhaust Port

8. Choose spray tip you want to use, pull back on

collar of nozzle extension, insert spray tip and

release collar. Tug on spray tip to make sure it is

securely in place. See "How to Use Spray Tips".

9. Engage trigger lock to spray gun trigger.

Trigger Lock

10. Move throttle lever to "Fast" position, shown here

as a rabbit.

Fast

Stop

Throttle

Lever in

STOP

position

NOTE: For a warm engine, be sure the throttle lever is

in the "Fast" position.

To start the engine for the very first time:

11. Make sure throttle lever is in "Fast" position

(indicated on the engine as a rabbit).

12. Push primer bulb firmly 5 times, waiting 2 seconds

between each push.

To start engine thereafter:

11. Make sure throttle lever is in "Fast" position

(indicated on the engine as a rabbit).

12. Press primer bulb firmly 3 times, waiting

2 seconds between each push. For a warm

engine, DO NOT press primer bulb.

13. Grasp starter grip handle and pull slowly until you

feel some resistance. Then pull rapidly to start

engine.

WARNING

]

When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

If engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze

trigger on spray gun.

14. Return starter grip handle slowly. DO NOT let rope

"snap back" against starter.

NOTE: Always keep the throttle lever in the "Fast"

)osition when operating the pressure washer.

a, cAuTmO. ]

• DO NOT move pressure washer while running.

• Always use handle to lift equipment.

• NEVER pull on hoses to move equipment.

WARNING

DO NOT touch hot surfaces.

Allow equipment to coo! before touching.

The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials.

Keep at least 3 feet of clearance on al! sides of pressure

washer for adequate cooling, maintenance and servicing.

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

How to Stop Your Pressure Washer

1. Let engine idle for two minutes.

2. Move throttle lever on engine to "Stop" position.

3. Squeeze trigger on spray gun to relieve

trapped pressure in hose to avoid injury.

WANNING

Keep high pressure hose connected to pump and spray

gun while system is pressurized.

Squeeze trigger on spray gun to relieve trapped

pressure, every time you stop engine, Engage trigger

lock on spray gun.

NOTE: A small amount of water will squirt out when

pressure is released.

4. Engage trigger lock on spray gun when not in use.

How to Use Spray Tips

The quick-connect on the nozzle extension allows you

to switch between four different spray tips. The spray

tips vary the spray pattern as shown above.

Follow these instructions to change spray tips:

1. Engage trigger lock on spray gun.

CAUTION

NEVER exchange spray tips without locking the trigger

lock on the trigger.

Pull back collar on quick-connect and pull current

spray tip off. Store spray tips in holder provided on

the nozzle extension.

Select desired spray tip:

• For gentle rinse, select white 40° spray tip.

• To scour surface, select yellow 15° or red 0°

spray tip.

• To apply chemical, select black spray tip.

Low Pressure

Black

Use to apply

chemical

High Pressure

////

40 ° White 15° Yellow 0° Red

Usage Tips

• Pull back on collar, insert new spray tip and

release collar. Tug on spray tip to make sure it is

securely in place.

• For most effective cleaning, keep spray tip from

8 to 24 inches away from cleaning surface. If you

get spray tip too close, you may damage cleaning

surface.

• DO NOT get closer than 6 inches when cleaning

tires.

Cleaning and Applying Chemical

IMPORTANT: Use chemicals designed specifically

for pressure washers. Household detergents could

damage the pump.

CAUTION

Starting the engine without all the hoses connected and

without the water turned ON will damage the pump.

Damage to equipment resulting from failure to follow this

instruction will void warranty,

Review spray tip use.

Prepare detergent solution as required by

manufacturer.

Place filter end of detergent siphoning tube into

detergent container.

CAUTION

When inserting the filter into a detergent solution bottle,

route the tube so as to keep it from inadvertently

contacting the hot muffler.

4. Make sure black spray tip is installed.

NOTE: Detergent cannot be applied with the high

pressure spray tips (White, Yellow, or Red).

5. Make sure garden hose is connected to water

inlet. Check that high pressure hose is connected

to spray gun and pump and start engine.

6. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward,

using long, even, overlapping strokes.

7. Allow detergent to soak in between 3-5 minutes

before washing and rinsing. Reapply as needed to

prevent surface from drying. DO NOT allow

detergent to dry on (prevents streaking).

IMPORTANT: You must flush the chemical injection

system after each use by placing the filter into a

bucket of clean water, then run the pressure washer in

low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1. Apply trigger lock to spray gun.

2. Remove black spray tip from nozzle extension.

3. Select and install desired high pressure spray tip

following instructions in "How to Use Spray Tips".

4. Keep spray gun a safe distance from the area you

plan to spray.

WARNnNG

Keep spray nozzle between 8 to 24 inches away from

cleaning surface.

Operate this unit on a stable surface.

Be extremely careful if you must use the pressure

washer from a ladder, scaffolding or any other relatively

unstable location.

Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury if gun Mcks back.

Apply a high pressure spray to a small area and

then check the surface for damage, if no damage is

found, you can assume it is okay to continue rinsing.

Start at top of area to be rinsed, working down with

same overlapping strokes as you used for cleaning.

C_eaning Detergent Siphoning Tube

if you used the detergent siphoning tube, you must

flush it with clean water before stopping the engine.

1. Place chemical injection siphon/filter in a bucket

furl of dean water.

Attach black spray tip.

Flush for 1-2 minutes.

Shut off engine.

iMPORTANT: Simply shutting OFF engine will not

release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun

to relieve the pressure in the hose.

Automatic Cool Down System

(Therma_ Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray

gun, circulating water in the pump can reach

temperatures above 125°F. The system engages to

cool the pump by discharging the warm water onto

the ground.

ENGINE TECHNICAL iNFORMATiON

This is a single cylinder, Uhead, air cooled engine, it

is a low emissions engine.

in the State of California, Model Series

100000 engines are certified by the California Air

Resources Board to meet emissions standards for

125 hours. Such certification does not grant the

purchaser, owner or operator of this engine any

additional warranties with respect to the performance

or operational life of this engine. The engine is

warranted solely according to the product and

emissions warranties stated elsewhere in this manual.

Power Ratings

The power ratings for an individual engine model are

initially developed by starting with SAE (Society of

Automotive Engineers) code J1940 (Small Engine

Power & Torque Rating Procedure) (Revision 2002-

05). Given both the wide array of products on which

our engines are placed, and the variety of

environmental issues applicable to operating the

equipment, it may be that the engine you have

purchased will not develop the rated horsepower when

used in a piece of power equipment (actual "on-site"

power). This difference is due to a variety of factors

including, but not limited to, the following: differences

in altitude, temperature, barometric pressure, humidity,

fuel, engine lubrication, maximum governed engine

speed, individual engine to engine variability, design of

the particular piece of power equipment, the manner in

which the engine is operated, engine run-in to reduce

friction and clean out of combustion chambers,

adjustments to the valves and carburetor, and other

factors. The power ratings may also be adjusted

based on comparisons to other similar engines utilized

in similar applications, and will therefore not

necessarily match the values derived using the

foregoing codes.

PRODUCT SPECiFiCATiONS

Pressure Washer Specifications

Pressure .................. 2150 PSI

Flow Rate ................. 1.9 GPM

Chemical Mix............... Use as directed

Water Supply Temperature .... Not to exceed 100°F

Shipping Weight ............ 57 Ibs.

Engine Specifications

Rated Horsepower ............ 4.0 at 3600 rpm

Bore ....................... 2.562 in. (65.09 mm)

Stroke ...................... 1.875 in. (47.63 mm)

Displacement ................ 9.67 in. (158.6 cc)

Spark Plug

Type: ..................... Champion RJ-19LM or

Equivalent

Set Gap To: ............... 0.030inch (0.76mm)

Armature Air Gap: ............ 0.006-0.010 in.

(0.15-0.25mm)

Valve clearance with valve springs installedand piston 1/4 in.

(6 mm) past top dead center (checkwhen engine iscold).

intake ...................... 0.005-0.007 in.

(0.13-0.!8 mm)

Exhaust .................... 0,007-0,009 in.

(0,18-0,23 ram)

Fuel Capacity ................ 1,0 Quarts

Oil Type:

Above 40° F ............... SAE 30

Below 40° F ............... SAE 5W-30 or 10W-30

NOTE: For practical operation, the horsepower

loading should not exceed 85% of rated horsepower.

Engine power will decrease 3-1/2% for each

1,000 feet (300 meters) above sea level and 1% for

each 10° F (5.6° C) above 77° F (25 ° C). It will

operate satisfactorily at an angle up to 15°.

OWNER'S RESPONSiBiLiTiES

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

MABNTENANCE SCHEDULE

FILL tN DATES AS YOU

COMPLETE REGULAR SERVICE

MAINTENANCE TASK

PRESSURE WASHER

Check/dean water inlet screen

Check high pressure hose

Check detergent hose

Check spray gun and assembly for leaks

Purge pump of air and contaminants

Change pump oil

Prepare pump for storage below 32°F

ENGINE

Before

Each Use

X _

OPERATING iNTERVALS

Every 25 I Every 50 Every 100

100-300m

Hours or

HoUrSyeary°r HoUrSyearlyOrYearly Hours

See Storage on pages 17-18

SERVICE DATES

Check oil level

Clean debris

Change engine oil

Service air cleaner

Service spark plug

Service spark arrester

Clean cooling system

Clean combustion chamber

Prepare for storage

X _

if unit is to remain idle for longer than 30 days.

Clean if clogged. Replace if perforated or torn.

2 Change oil after the first (5) operating hours and every 50 hours or yearly thereafter.

Change sooner when operating under dirty or dusty conditions.

Replace more often under dirty or dusty conditions.

GENERAL RECOMMENDATIONS EMISSION CONTROL

Regular maintenance wilJ improve the performance

and extend the life of the pressure washer. See any

authorized Sears deaJer for service.

The pressure washer warranty does not cover items

that have been subjected to operator abuse or

negligence. To receive full value from the warranty,

the operator must maintain pressure washer as

instructed in this manual including proper storage as

detailed in "Storage" on pages 17-18.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least

once each season. Follow the requirements in the

"Maintenance Schedule" chart above.

NOTE: Once a year you should clean or replace the

spark plug and replace the air filter. A new spark plug

and clean air filter assure proper fuel-air mixture and

help your engine run better and last longer.

If equipped with inflatable tires, keep the air pressure

at the value marked on the tire or within 15 and 40 psi.

Maintenance, replacement or repair of the emission

control devices and systems may be performed by any

non-road engine repair establishment or individual.

BEFORE EACH USE

1. Check engine oil level.

2. Check water inlet screen for damage.

3. Check in-line filter for debris.

4. Check high pressure hose for leaks.

5. Check chemical filters for damage.

6. Check gun and nozzle extension assembly for

leaks.

7. Purge pump of air and contaminants.

PRESSURE WASHER

C_ean Debris

Daily or before use, clean accumulated debris from

pressure washer. Keep linkage, spring and controls

clean. Keep area around and behind muffler free from

any combustible debris.

Pressurewasherpartsshouldbekeptcleantoreducethe

riskofoverheatingandignitionofaccumulateddebris.

CAUTION

• DO NOT insert any objects through cooling slots.

° Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil,

etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. inspect cooling air slots and openings on

the pressure washer. These openings must be kept

clean and unobstructed.

Check and C_ean Jn_et Screen

Examine garden hose inlet screen. Clean if it is

clogged or replace if it is torn.

Check High Pressure Hose

High pressure hoses can develop leaks from wear,

kinking, or abuse, inspect hose before each use.

Check for cuts, leaks, abrasions, bulging of cover, or

damage or movement of couplings, if any of these

conditions exist, replace hose immediately.

• NEVER repair high pressure hose, Replace it,

• Replacement hose rating MUST exceed maximum

pressure rating of unit.

Check Gun and Nozzle Extension

Examine hose connection to gun and make sure it is

secure. Test trigger by pressing it and making sure it

springs back into place when you release it. Engage

trigger lock and test trigger. You should not be able to

press trigger. Replace gun immediately if it fails any of

these tests.

Check in-Line Fi_ter

Refer to the illustration and service the in-line filter if it

becomes clogged, as follows:

Nozzle extension

O-ring

Detach nozzle extension from gun and remove

o-dng and screen from nozzle extension. Flush

screen, gun, and nozzle extension with clean water

to clear debris.

2. Place in-line filter screen into threaded end of

nozzle extension. Direction does not matter. Push

screen in with eraser end of pencil until it rests flat

at bottom of opening. Take care not to bend screen.

3. Place o-ring into recess. Push o-ring snugly against

in-line filter screen.

4. Assemble nozzle extension to spray gun, as

described earlier in manual.

NozzRe Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.

The principal cause of excessive pump pressure is a

spray tip clogged or restricted with foreign materials,

such as dirt, etc. To correct the problem, immediately

clean the spray tip following these instructions:

1. Shut off engine and turn off water supply.

2. Remove spray tip from end of nozzle extension.

3. Remove in-line filter from other end of nozzle

extension.

Use a small paper clip to free any foreign material

clogging or restricting spray tip.

5. Using a garden hose, remove additional debris by

back flushing water through nozzle extension.

Back flush between 30 to 60 seconds.

6. Reinstall spray tip and in-line filter into nozzle

extension.

7. Reconnect nozzle extension to spray gun.

8. Reconnect water supply, turn on water, and start

engine.

9. Test pressure washer by operating with each

quick connect spray tips.

O-Ring Maintenance

Purchase an O-Ring Repair Kit at your local Sears or by

caJJing1-800-366-PART or online at www.sears.com. Jtis

not included with the pressure washer. This kit includes

replacement o-rings, rubber washer and water inlet filter.

Refer to the instruction sheet provided in the kit to service

your unit's o-rings.

WARNING

NEVER repair leaking connections with sealant of any

kind. Replace o-ring or sea!,

Pump Maintenance

Changing Pump Oit

Change oUevery 50 hours or once yearly, whichever

occurs first.

NOTE: You must purchase an approved bottle of

pump off by calling 1-800-366-PART or online at

www.sears, com.

Change pump oil as follows:

1. Drain engine oil and fuel from pressure washer.

2. Use a 8mm allen wrench to remove black pump

oil cap between high pressure outlet and garden

hose inlet.

Oil Cap

Change oit while engine is still warm from running,

as follows:

1. Drain fuel tank by running pressure washer until

fuel tank is empty.

2. Disconnect spark plug wire and keep it away from

spark plug.

3. Clean area around oil fill, remove oil fill

cap/dipstick. Wipe dipstick clean.

4. Tip your pressure washer to drain oil from oil fill

into a suitable container making sure you tip your

unit away from spark plug and air cleaner. When

crankcase is empty, return pressure washer to

upright position.

5. Wipe dipstick clean, insert it into oil fill hole and

tighten securely, remove dipstick. Add

recommended oil up to "Full" mark on dipstick.

Pour slowly. Wipe dipstick clean each time oil

level is checked. DO NOT overfill.

6. Install oil fill cap/dipstick, tighten securely.

7. Wipe up any remaining oil.

8. Reconnect spark plug wire to spark plug.

3. TiJtpressure washer to drain oil into an approved

container until it drips slowly from pump.

4. Tilt pressure washer in opposite direction and

empty premeasured pump oiJbottle into same

opening (a small funnel may be helpful).

5. )nstaU black pump oJ(cap and tighten firmly.

6. Set pressure washer in upright position. Add fuel

and engine oil.

ENGINE MAINTENANCE

Service Air Cleaner

Your engine will not run properly and may be

damaged if you run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of

operation or once each year, whichever comes first.

Service more often if operating under dirty or dusty

conditions. Replacements are available at your local

Sears service center.

To service the air c(eaner, fo)iow these steps:

1. Remove screw.

Checking OH Leve(

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

Changing Oil

Change engine oil after the first 5 hours and every

50 hours thereafter. If you are using your pressure

washer under extremely dirty or dusty conditions, or in

extremely hot weather, change oil more often.

( cAuTmO.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals,

• Thoroughly wash exposed areas with soap and water,

KEEP OUT OF REACH OF CHILDREN.

DON'T POLLUTE. CONSERVE

RESOURCES. RETURN USED OIL TO

_COLLECT)ON CENTERS.

2. Carefully remove air cleaner assembly to prevent

debris from falling into carburetor.

3. Take air cleaner assembly apart and clean all

parts. Wash foam air cleaner in liquid detergent

and water. Squeeze dry in a clean cloth.

4. SATURATE foam air cleaner in engine oil and

squeeze in a clean cloth to remove excess oil.

5. Reinstall clean or new foam air cleaner in body.

6. Install air cleaner securely on carburetor with screw.

NOTE: You can purchase new air cleaner elements by

ca(ling 1-800-366-PART.

Service Spark Pmug

Service the spark plug every 100 hours of operation or

yearly, whichever occurs first.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

DO NOT check for spark with spark plug removed.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug with recommended plug if

electrodes are worn or if insulator is cracked or

chipped.

4. Check electrode gap with wire feeler gauge and

set gap at 0.030 inches (0.76mm), if necessary.

5. Install spark plug, tighten securely.

NOTE: You can purchase a new spark plug by calling

1-800-366-PART.

Spark Arrester Service

Your engine is not factory-equipped with a spark

arrester. In some areas, it is illegal to operate an

engine without a spark attester. Check local laws and

regulations. A spark arrester is available from your

nearest Sears service center. If you need to order a

spark arrester, please call 1-800-366-PART.

The spark attester must be serviced every 50 hours to

keep it functioning as designed.

if the engine has been running, the muffler will be very

hot. Allow the muffler to cool before servicing spark

attester.

WARN NG

DO NOT touch hot surfaces,

Allow equipment to coo! before touching.

The pressure washer must be at least 5 feet from

structures having combustible walls and/or other

combustible materials,

Keep at least 3 feet of clearance on all sides of pressure

washer for adequate cooling, maintenance and servicing.

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws, Federal laws apply on

federal lands, If you equip the muffler with a spark arrester,

it must be maintained in effective working order,

• Remove spark attester screen for cleaning and

inspection.

• Replace if screen is damaged.

Air Cooling System

Over time debris may accumulate in cylinder cooling

fins and cannot be observed without partial engine

disassembly. For this reason, we recommend you have

an authorized Sears service dealer clean the cooling

system per recommended intervals (see "Maintenance

Schedule" on page 13). Equally important is to keep top

of engine free from debris. See "Clean Debris".

Keep areas within heavy line clear of debris.

C_ean Combustion Chamber

We recommend you have an authorized Sears sewice

dealer remove combustion deposits from the cylinder,

cylinder head, top of piston and around valves per

recommended intervals (see "Maintenance Schedule"

on page 13).

AFTER EACH USE

Water should not remain in the unit for long periods of

time. Sediments or minerals can deposit on pump

parts and "freeze" pump action. Follow these

procedures after every use:

1. Flush detergent siphoning tube by placing the filter

into a pail of clean water while running pressure

washer in low pressure mode. Flush for one to two

minutes.

2. Shut off engine, let it cool, then remove all hoses.

3. Disconnect spark plug wire from spark plug.

4. Empty pump of all liquids by pulling recoil handle

about 6 times. This should remove most liquid in

pump.

5. if storing for more than 30 days see "Long Term

Storage" on next page.

6. Coil high pressure hose and inspect it for damage.

Cuts in hose or fraying could result in leaks and

loss of pressure. Should any damage be found,

replace hose. DO NOT attempt to repair a

damaged hose. Replace hose with genuine Sears

part.

7. Disconnect hose from spray gun and high

pressure outlet on pump. Drain water from hose,

gun, and nozzle extension. Use a rag to wipe off

hose.

8. Reconnect spark plug wire to spark plug.

9. Store unit in a clean, dry area.

WARNING

WINTER STORAGE

CAUTION

* Failure to do so will permanently damage your pump

and render your unit inoperable.

, Freeze damage is not covered under warranty.

To protect the unit from freezing temperatures:

1. Flush detergent siphoning tube by placing filter

into a pail of clean water while running pressure

washer in low pressure mode. Flush for one to two

minutes.

2. Empty pump of all pumped liquids by pulling recoil

handle about 6 times. This should remove most

liquid in pump.

3. Use pump saver, available at Sears retail item

71-74403, to treat pump. This minimizes freeze

damage and lubricates pistons and seals.

4. if pump saver is not available, connect a 3-foot

section of garden hose to water inlet adapter.

Pour RV-antifreeze (antifreeze without alcohol)

into hose. Pull recoil handle twice. Disconnect

3-foot hose.

WHEN STORBNGFUEL OR EQUmPMENTWiTH FUEL IN

TANK

Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that havepilot light or other

ignition source because they can ignite fuel vapors.

WHEN DRAINING FUEL

Turn pressure washer OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

Drain fuel tank outdoors.

Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

DO NOT light a cigarette or smoke.

LONG TERM STORAGE

if you do not plan to use the pressure washer for more

than 30 days, you must prepare the engine and pump

for long term storage.

it is important to prevent gum deposits from forming in

essential fuel system parts such as the carburetor, fuel

filter, fuel hose or tank during storage. Also,

experience indicates that alcohol-blended fuels (called

gasohol, ethanol or methanol) can attract moisture,

which leads to separation and formation of acids

during storage. Acidic gas can damage the fuel

system of an engine while in storage.

Protect Fuel System

Fuel Additive:

if adding a fuel additive, fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote

fuel deterioration during storage. Engine and fue[ can

be stored up to 24 months with additive.

• Add fue[ additive following manufacturer's

instructions.

• Make sure you have water supply to pump inlet

connected and turned ON.

• Run the engine outdoors for 10 minutes to be sure

that treated fuel has replaced the untreated fuel in

the carburetor.

If fuel additive is not used, remove all fuel from tank

and run engine until it stops from lack of fuel.

Change Oil

While engine is still warm, drain oil from crankcase.

Refill with recommended grade. See "Changing Oil" on

page 15.

Oil Cylinder Bore

• Remove spark plug. Squirt about 1/2 oz. of clean

engine oil into the cylinder. Cover spark plug hole

with rag. Pui[ recoil handle slowly to distribute oil.

Avoid spray from spark plug hole.

• Instal[ spark plug. DO NOT connect spark plug

wire.

Protect Pump

To protect the pump use Sears pump saver to prevent

freeze damage and lubricate pistons and seals.

CAUTION

• Failure to do so will permanently damage your pump

and render your unit inoperable,

• Freeze damage is not covered under warranty.

NOTE: Sears pump saver, item number 71-74403, is

available as an optional accessory. It is not included with

the pressure washer.

,_ CAUTION

Always wear eye protection when using PumpSaver.

To use the pump saver:

1. Attach hose on pump saver can to pump inlet.

2. Push in can top to dispense pump saver.

3. When pump saver fluid begins to exit pump outlet,

the pump is protected.

4. Remove pump saver from pump inlet.

OTHER

• DO NOT store fuel from one season to another.

• if possible, store your unit indoors and cover it to

give protection from dust and dirt. BE SURE TO

EMPTY THE FUEL TANK.

WARNING

DO NOT place a storage cover over a hot pressure

washer,

Let equipment coo! for a sufficient time before placing

the cover on the equipment.

Prob(em

Pump has followingproblems:

failureto produce pressure,

erraticpressure_chattering_loss

of pressure, low water volume.

Detergent failsto mix with spray.

Engine runs good at no-(oad but

"bogs" when load isadded.

Engine wii) not start; or starts

and runs rough.

Engine shuts down during

operation.

Engine lacks power.

Engine "hunts" or ratters.

Cause

Low pressure spray tip installed.

Water inlet is blocked.

3. )nadequate water supply.

4. Inlet hose is kinked or leaking.

5. Clogged inlet hose strainer.

6. Water supp(y is over 100°F.

7. High pressure hose is blocked

or leaks.

8. Gun (eaks.

9. Spray tip is obstructed.

10. Pump (sfau(ty.

Detergent siphoning tube is not

submerged.

Chemica( filter is clogged or

cracked.

3. Dirty (n=(inefilter.

4. High pressure spray tip

(nsta((ed.

Engine speed is too s(ow.

Low oil )eve(.

Dirty air cleaner.

3. Out of gaso(ine.

4. Sta(e gasoline.

5. Spark plug wire not connected

Correction

Replace spray tip with high

pressure spray tip.

Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch

leak.

5. Check and clean inlet hose

strainer.

6. Provide cooler water supp(y.

7. Clear blocks in outlet hose.

8. Rep)ace gun.

9. Clean spray tip.

10. Contact Sears service facility.

insert detergent siphoning tube

into detergent.

Clean or rep(ace filter/detergent

siphoning tube.

3. See "Check In=Line Filter".

4. Rep(ace spray tip with low

pressure spray tip.

Move throttle contro( to FAST

position. (f engine still "bogs down",

contact Sears service faci(ity.

F(((crankcase to proper (eve(.

Clean or rep(ace air cleaner.

3. F(((fuel tank.

4. Drain gas tank; fi((with flesh

fuel

5. Connect wire to spark plug.

to spark plug.

6. Bad spark plug.

7. Water in gasoline.

8. Overchoking.

6. Replace spark plug.

7. Drain gas tank; fiii with fresh

fuel.

8. Open choke fully and crank

engine.

9. Excessively rich fuel mixture.

10. Intake valve stuck open or

closed.

11. Engine has lost compression.

Out of gasoline.

Dirty air filter.

Choke is opened too soon.

9. Contact Sears service facility.

10. Contact Sears service facility.

11. Contact Sears service facility.

F(((fuel tank.

Replace air filter.

Move choke to halfway position until

engine runs smoothly.

CRAFTSMAN 2,150 PS_ Pressure Washer 580.752010

Main Unit _ Exploded View and Parts List

Item Part # Description

1 196519GS BASE

2 192525GS KIT, Pump/Engine Mounting

Hardware

3 196006GS HOSE

4 193482GS GUN

5 192199GS ASSY, Extension

6 196278GS KIT, Spray Tips

7 194298GS RELIEF, Thermal

8 23139GS KEY

9 194216GS ASSY, Pump (see page 21)

900 NSP ENGINE (10D902=0133=D2)

1terns Not illustrated

Part #

195927GS

AB3061BGS

195851ZZGS

195983AEGS

195983AFGS

195983AHGS

87815GS

192703GS

196712GS

192754GS

Optional Accessories Not Htustrated

7175187GS

7175197GS

7175199GS

190249GS

7175116GS

100513GS

7174403GS

7174300GS

7174301GS

7174302GS

7174303GS

7174307GS

Garden Hose Quick Connect

Accessory Quick Connect

Rotating Brush Kit

25' Replacement Hose

O Ring Repair Kit

25' Extension Hose

Pump Saver

House Wash Concentrate (makes 4 gallons)

Deck Wash Concentrate (makes 2 gallons)

Vehicle/Boat Wash Concentrate (makes 4 gallons)

Degreaser Concentrate (makes 4 gallons)

Mold/Mildew Concentrate (makes 2 gallons)

//-

Description

MANUAL, Owners

OIL BOTTLE

NOZZLE, QC Black

NOZZLE, QC, Red

NOZZLE, QC, Yellow

NOZZLE, QC, White

GOGGLES

DECAL, Clean Carry

KIT, Decal, Srv

DECAL, Warning

Page is loading ...

Craftsman 580.75201 User manual

Brand: Craftsman

Model: 580.75201

Category: High-pressure cleaners

Type: User manual

This manual is also suitable for

580752010

Download PDF

report

in other languages

español: Craftsman 580.75201 Manual de usuario

Craftsman 580.75201 User manual

This manual is also suitable for

Craftsman 580.75201 User manual

in other languages

Related papers