Craftsman 580752581 Owner's manual

Brand: Craftsman

Model: 580752581

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580.752581

Operator'sIVianual

3000 MAXPSI*

2.7 MAXGPiVi

iViodelNo. 580.752581

HOURS: IVlon.- Fri. Ba.m. to 5 p.m. (CT)

WARNING

Beforeusing this product, readthis

manualand follow all Safety Rules

and Operatinginstructions.

ADVERTENCIA

Antes deutilizar el producto, lea este

manualy siga todas las Reglasde

Seguridad eInstrucciones de Uso.

,, Safety

,, Assembly

,, Operation

,,iVlaintenance

,, Parts

,, Espafiol, p. 32

* This pressure washer is rated in accordance to the PressureWasher Manufacturers Association

(PWMA) standard PWI01 (Testing and Rating Performance of Pressure Washers).

* Esta limpiadora a presiOnest_ clasificada conforme a la norma PWl01 (comprobaciOn y clasificaciOn de rendimiento de limpiadoras

a presiOn)de la AsociaciOn defabricantes de bombas a presiOn(Pressure Washer Manufacturers Association, PWMA).

Sears, Roebuckand Co., HoffrnanEstates,IL 60179 U.S.A.

Visit our Craftsman website: www.craftsman.com

Part No. 312344GS Draft - (02/01/2010)

WARRANTY .......................................... 2

REPAIRPROTECTIONAGREEMENT........................ 2

SAFETYRULES...................................... 3-5

FEATURESAND CONTROLS.............................. 6

ASSEMBLY........................................ 7-10

OPERATION....................................... 11-15

SPECIFICATIONS..................................... 16

MAINTENANCE.................................... 17-20

STORAGE........................................... 21

TROUBLESHOOTING.................................. 22

REPLACEMENTPARTS.............................. 23-28

NOTES............................................. 29

EMISSIONCONTROLWARRANTY..................... 30-31

ESPANOL......................................... 32-55

HOWTO ORDERPARTS........................ BACKPAGE

CRAFTSMANLIMITEDWARRANTY

If this Craftsmanproduct fails due to a defect in material or workmanship within two years from the date of purchase, return it

to anySearsstore, Sears Parts & RepairService Center,or other Craftsmanoutlet in the United Statesfor free repair (or

replacementif repair proves impossible).

This warranty appliesfor only 90 days from the dateof purchase if this product is ever usedfor commercial or rental

purposes.

Thiswarranty coversONLYdefects in material and workmanship. Sears wiil NOTpayfor:

• Expendableitems that canwear out from normal usewithin the warranty period, such as spray guns, hoses, nozzle

extensions, nozzles,filters andspark plugs.

• Repairsnecessarybecauseof accident, or failure to operateor maintain the product according to all supplied instructions.

• Preventivemaintenance,or repairs necessarydue to improper fuel mixture, contaminated or stalefuel.

This warranty givesyou specific legal rights, and you may also haveother rights which vary from stateto state.

Sears,Roebuckand Co., HoffrnanEstates,IL 60179

Congratulations on making a smart purchase.

Your new Craftsman® product is designed and manufactured

for years of dependableoperation. But like all products, it

may require repair from time to time. That's when havinga

Repair ProtectionAgreement can saveyou money and

aggravation.

Here's whatthe Repair Protection Agreement* includes:

* Expert service by our 10,000 professional repair

specialists

, Unlimited service and no charge for parts and labor on

all covered repairs

, Product replacementup to $1500 if your covered

product can't befixed

, Discount of 10% from regular priceof serviceand related

installed parts not covered by the agreement;also, 10%

off regular price of preventivemaintenancecheck

, Fasthelp byphone-we caii it Rapid Resolution- phone

support from a Sears representative.Think of us as a

"talking owner's manual".

Onceyou purchasethe RepairProtection Agreement,a

simple phone carlis all it takes for you to schedule service.

You cancarl anytimeday or night, or schedule a service

appointment online.

The Repair ProtectionAgreement is a risk-free purchase. If

you cancelfor any reasonduring the product warranty

period,we will provide a full refund. Or, a prorated refund

anytime after the product warranty period expires. Purchase

your RepairProtectionAgreement today!

Some limitations and exclusions apply. Forpricesand

additional informationin the U.S.A. call 1-800-827-6655.

* Coverage in Canadavaries on someitems. Forfuji

details, caii Sears Canadaat 1-800-361-6665.

Sears InstallationService

ForSearsprofessional installation of home appliances,

garagedoor openers, water heaters,and other major home

items, in the U.S.A.or Canadacall 1-800-4-1VlY-HOIVlE®.

ToxicFumes

SlipperySurface

Readthis manual carefully and become familiar

with yourpressure washer. Knowitsapplications,

itslimitations, and any hazardsinvolved.

Important Safety Information

Safety Symbols and Meanings

Kickback ElectricalShock

Fall FluidInjection

Fire

Explosion Operator'sManual

MovingParts FlyingObjects ChemicalBurn

Hot Surface

,_, Thesafety alertsymbol indicatesa potential personal

injury hazard.A signalword (DANGER,WARNING,or

CAUTION)is usedwith thealert symbol to designatea degree

or levelof hazardseriousness.A safety symbol may be used

to representthe typeof hazard.Thesignal word NOTICEis

usedto addresspracticesnot relatedto personalinjury.

_i, DANGERindicatesa hazardwhich, if not avoided, will

result in deathor serious injury.

_i, WARNINGindicates a hazardwhich, if not avoided, could

result in deathor serious injury.

_i, CAUTIONindicates a hazardwhich, if not avoided, could

result in minor or moderate injury.

NOTICEaddresspractices not relatedto personal injury.

_i, WARNING Theengineexhaustfrom this product

contains chemicals known to the Stateof Californiato

cause cancer,birth defects,or other reproductive harm.

_i, WARNING This product contains lead and lead

compounds, known to the State of Californiato cause

birth defects or other reproductive harm. Washyour

handsafter handling this product.

_i, WARNING Runningengine gives off carbon

monoxide, an odorless, colorless, poison gas.

_ Breathingcarbon monoxide headache,

can cause

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

Some chemicals or detergentsmay be harmful if inhaled

or ingested, causing severenausea,fainting, or

poisoning.

• OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor run engineindoorsor in anenclosedarea,

evenifwindowsanddoorsareopen.

• Usea respiratoror maskwheneverthereisa chancethat

vaporsmaybeinhaled.

• Readall instructionswith masksoyouarecertainthemaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

_i, WARNING ChemicalBurn Hazard.

Chemicalscould causebodily injury, property

damageor death.

• DONOTusecausticliquidwith pressurewasher.

• UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

A. WARNING Startercord kickback(rapid retraction)can

result in bodily injury. Kickbackwill pull hand and

,_arm toward enginefaster thanyou can let go.

Broken bones,fractures, bruises, or sprains

could result.

• NEVERpullstarter cord without first relieving spraygun

pressure.

• When starting engine, pull cord slowly until resistanceisfelt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, pressred button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

A. WARNING Riskof electrocution.

"_.dh Contactwith power source can causeelectric

shock or burn.

• NEVERspraynearpowersource.

A. WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DONOTallow CHILDRENto operate pressure washer.

• NEVERrepairhigh pressure hose.Replaceit.

• NEVERrepairleaking connections with sealantof any kind.

Replaceo-ring or seal.

• NEVERconnect high pressure hose to nozzleextension.

• Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

• ALWAYS point spray gun in safedirection, pressred button

andsqueezespray guntrigger to releasehighpressure, every

time you stop engine.

• NEVERaim spray gun at people,animals, or plants.

• DO NOTsecure spraygun inopen position.

• DO NOTleavespray gun unattendedwhile machine is running.

• NEVERuseaspray gun which does not haveatrigger lock or

trigger guardin placeand in working order.

• Always be certain spray gun, nozzlesandaccessoriesare

correctly attached.

A. WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHENADDING OR DRAININGFUEL

* Turn pressurewasher OFFand let it cool at least2 minutes

before removing fuel cap. Loosen capslowly to relievepressure

in tank.

, Fill or drain fuel tank outdoors.

, DONOToverfill tank. Allow spacefor fuel expansion.

, Iffuel spills, wait until it evaporatesbeforestarting engine.

, Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

, DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

* Ensurespark plug, muffler,fuel cap,and air cleanerarein place.

* DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

, DONOTtip engine or equipment at anglewhich causes fuel to

spill.

, DONOTsprayflammable liquids.

WHENTRANSPORTING,MOVINGOR REPAIRINGEQUIPMENT

, Transport/move/repair with fuel tank EMPTYor with fuel shutoff

valveOFF.

, DONOTtip engine or equipment at anglewhich causes fuel to

spill.

, Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELIN TANK

* Store awayfrom furnaces, stoves,water heaters,clothes

dryers, or other appliancesthat havepilot light or other ignition

source becausethey can ignitefuel vapors.

A. WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipmentto cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• It is aviolation of California Public Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federaljurisdictions may have similar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

_i, WARNING Use of pressure washer can create

puddles and slippery surfaces.

_' Kickback from spray gun can cause you

to fall.

• Operatepressurewasher from a stablesurface.

• Thecleaning areashould haveadequateslopes anddrainageto

reducethe possibility of a fall due to slippery surfaces.

• Beextremely careful if you must usethe pressurewasherfrom

a ladder,scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

A, WARNING Unintentional sparking can result in fire or

_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE

WASHER

• Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

• Use approvedspark plug tester.

• DONOTcheckfor sparkwith spark plug removed.

A, WARNING Starter and other rotating parts can

entanglehands, hair, clothing, or accessories.

. NEVERoperatepressurewasherwithoutprotectivehousingor

covers.

. DONOTwearlooseclothing,jewelryor anythingthat maybe

caughtin thestarteror otherrotatingparts.

* Tieuplonghairandremovejewelry.

A, WARNING Riskof eyeinjury.

Spray cansplash back or propel objects.

• Always wear indirect vented (chemical splash) safetygoggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

NOTICE High pressure spray may damagefragile items

including glass.

• DONOTpointspraygunatglasswhenusingMAXspraypattern

in selectornozzle.

= NEVERaim spray gun at plants.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• If you have questions about intended use,ask dealer or contact

Sears.

• NEVERoperate units with broken or missing parts, or without

protective housing or covers.

• DO NOTby-pass any safetydevice on this machine.

• DONOTtamper with governed speed.

• DONOToperate pressure washer above rated pressure.

• DONOTmodify pressure washer in any way.

• Beforestarting pressure washer in cold weather,check all parts

of the equipment to besure ice has not formed there.

• NEVERmove machine by pulling on hoses. Use handle provided

on unit.

• Checkfuel system for leaksor signs of deterioration, such as

chafed or spongy hose,loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure washer.

• This equipmentis designedto be usedwith Searsauthorized parts

ONLY.If equipment is usedwith parts that DONOTcomply with

minimum specifications, userassumesall risksand liabilities.

KNOWYOURPRESSUREWASHER

Readthe Operator's Manual and safetyrules before operating yourpressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A- AccessoryTray-- Provides convenient storagefor accessories,

such as gun, nozzleextension, etc.

B- HoseWrap and High PressureHose -- Hosewrap provides

easytransport and handling of the high pressure hose.Connect

one end of hose to water pump and the other end to spray gun.

C- Recoil Starter-- Usedfor starting the engine manually.

D - ProjectPro@ PerfectMWMSiphon -- Mixes concentrate with

pressure washer spray.

E- Oil Fill/Dipstick -- Check,addand drain engine oil here.

F - Bottle Bracket -- Cleaningsolution bottle fits in wire form

bracket here.Concentratebottle not included.

(; - EngineIdentification-- Provides model, type and code of

engine. Pleasehavethese readilyavailable if calling for

assistance.

H - Water Inlet -- Connectionfor garden hose.

J - Automatic Cool Down System -- Cycleswaterthrough pump

when water reaches125°-155°F. Warm water will dischargefrom

pump onto ground. This system preventsinternal pump damage.

K- Pump-- Develops high pressure.

L - DetergentSiphoningTube/Filter-- Useto siphonpressurewasher

safedetergentsintothe low pressurestream.

IVi- EngineRockerSwitch -- Pushthis switch to on position (I or

ON) before using recoil starter. Push switch to off position (0

or OFF)for shutting off engine.

N - Selector Nozzle-- Containsfive different spray pattern nozzles

for various applications.

P - Air Filter -- Protects engine byfiltering dust and debris out of

intakeair.

R - Fuel Tank-- Fill tank with regular unleadedfuel. Always leave

room for fuel expansion.

S - NozzleExtensionwith QuickConnect-- Allows you to switch

betweenselector nozzleand optional nozzleaccessories.

T - Fold Down Handle-- Handleand accessorytray fold fiat atop

cold engine for space-saving storage.

U- SprayGun-- Controls the application of water onto cleaning

surface with trigger device, includes trigger lock.

items Not Shown:

identificationLabel (near rear of base plate) -- Provides model

and serial number of pressure washer. Pleasehavethese readily

available if callingfor assistance.

HighPressure Outlet-- Connectionfor high pressurehose.

Warning/Operating instructionsTag-- Identifieshazardsand proper

procedureto start/stop pressurewasher.

Your pressure washer requires some assembly and is ready

for useonly after it has been properly servicedwith the

recommendedoil and fuel.

If you haveany problemswith theassemblyof your

pressurewasher, please call the pressurewasher helpline

at 1=800-222-3136.

UNPACKTHEPRESSUREWASHER

1. Removeeverythingfrom carton except pressurewasher.

2. Opencarton completely by cutting eachcorner from top

to bottom.

6. Connectpressure hoseto spray gun and pump.

7. Connectwater supply to pump.

8. Attach nozzleextension to spray gun.

9. Attach quick connect selector nozzleto nozzleextension.

Attach HandleandAccessory Tray

1. Placehandle(A) onto handle supports (B) connectedto

main unit. Make sure holes (C) in handlealign with holes

3. Removepressure washer from carton.

CARTONCONTENTS

Checkall contents. If anyparts are missing or damaged,call

the pressure washer helplineat 1-800-222-3136.

• Main Unit

• Handle

• AccessoryTray

• High PressureHose

• Spray Gun

• NozzleExtensionwith Quick ConnectFitting

• Quick ConnectSelector Nozzle

• Oil Bottle

• HoseWrap

• DetergentSiphoning Hose/Filter

• Bottle BracketWireform (2)

• PerfectMixTM Siphoning Unit/Hose

• Parts Bag(which includes the following):

• Operator's Manual

• Owner's Registration Card

• HandleFasteningHardwareKit (whichincludes):

• HandleBolts (2)

• CarriageBolt (2)

• Rope Guide(1)

• Plastic Knobsfor Handle(2)

• Plastic Knob (3)

• TreeClips (4)

Becomefamiliar with eachpiece beforeassemblingthe

pressure washer, identify all contents with the illustration on

page 6. if any parts are missing or damaged, call the

pressure washer helpline at1-800-222-3136.

ASSEMBLINGPRESSUREWASHER

Your Craftsmanpressure washer will needassembly before

operation:

1. Fill out and sendin registration card.

2. Attach handle and accessorytray.

3. Connectdetergent siphon hoseto pump.

4. Add oil to engine crankcase.

5. Add fuel to fuel tank.

NOTICE

hot.

insert handle carriagebolts (D) through holes from

inside of unit and attach a plastic knob (E) from outside

of unit. Tighten by hand. Byloosening both knobs to the

middle section of the attachmentbolt, the upper handle

canfold forward to store fiat atop the cold engine.

DONOTfold the handle down while the engine is

Placeaccessorytray (F) over holes (6) on handle

(viewing from backof unit). Pushthe tree clips (H) into

the holes until they sit fiat against the accessorytray.

insert supplied accessoriesin spacesprovided in

accessorytray. See How to UseAccessory Tray.

Attach rope guide (A) through handlewith plastic knob

(B). Tighten by hand. Route engine recoil rope through

guide.

Align hosewrap (C)to the back side of accessorytray.

Locate notch with "unlock"icon (B) on hosewrap.

Position notch at top with hosewrap in vertical position.

Clips in the back of accessorytray should slide into the

grooves on the inside surface of hosewrap. Slide hose

wrap on back of accessorytray and rotate 1/8 turn until

"locked"icon (E) is invertical position. Hosewrap is

easily removed from the accessorytray for wrapping and

unwrapping of the high pressure hose. A clip to secure

the hoseon the reel makesit easyto wrap the hose

while it is detachedfrom the accessorytray.

Standard Siphon Tube

Cleartube with filter:

When using the clear siphon tube, dilute

1 part PerfectlViWMExtremeConcentrate

to 16 parts water (4 oz of concentrate

makes1/2 gallon of mix.)

Attach ProjectPro@PerfectiVIWMSiphon to

Pump

Attach the hose end of the blue PerfectMWMSiphon (J) to

the barbed hosefitting (K) on the pump.

Attach PerfectiVlixTM DetergentSiphon to

ConcentrateBottle

PlacePerfectMixTM bottle (not included) in the wire-form

bracketon the handle. Removecap from bottle and insert the

PerfectMixTM Siphon (L). Screwthe siphon unit to the top of

the bottle (IV]).Usethe clip on the cap (L) to snapsiphon to

wire form bracketwhen siphon is not in a concentrate bottle.

Attach bottle brackets (F) to handlewith carriage bolts

(G) and black plastic knobs (H). Tighten by hand.

2-iN-1 SoapSystem

The pressurewasher is equippedwith two detergent

siphoning hoses.

ProjectProPerfectMWMSiphon

Blue tube with blue bottle cap:

When usingthe blue PerfectMixTM siphon, use

the PerfectMixTM ExtremeConcentratestraight

from the bottle.

Add Engine Oil

1. Placepressurewasher on a flat, levelsurface.

2. Cleanareaaround oil fill and removeyellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• DONOTattemptto crank or startthe engine before it has been

properly servicedwith the recommended oil. This may result in an

enginefailure.

4. Replaceoil fill cap/dipstick and fully tighten.

AddFuel

Fuel mustmeet these requirements:

• Clean,fresh, unleadedgasoline.

• A minimum of 87 octane/87 AKI (91 RON).High altitude

use, see HighAltitude.

• Gasolinewith up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE Avoid pressure washer damage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

• DONOTuseunapprovedgasolinesuchasE85.

• DONOTmixoil in gasoline.

• DONOTmodifyengineto runonalternatefuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizerwhen adding fuel. SeeStorage.All fuel is not the

same. If you experiencestarting or performanceproblems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline. The

emission control system for this engine is EM (Engine

Modifications).

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosion can causesevere burns

or death.

WHENADDINGFUEL

• Turnpressure washerOFFand let it cool at least2 minutes

before removing fuel cap. Loosen capslowly to relievepressure

in tank.

• Fill fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigarette or smoke.

Cleanarea around fuel fill cap, remove cap.

Slowly add regular unleadedfuel (A) to fuel tank (B). Be

careful not to overfill. To allow for fuel expansion, do not

fill abovethe bottom of thefuel tank neck.

N NN NNNNNN NN N

N NN NNNNNN NN

J N N_ NN_NNN NN _-"_

3. Install fuel capand wait for any spilled fuel to evaporate.

CAUTION! Alcohol-blended fuels (calledgasohol, ethanol or

methanol) canattract moisture, which leadsto separation and

formation of acids during storage.Acidic gascandamagethe

fuel system of an enginewhile in storage.

To avoid engine problems, the fuel system should be treated

with a fuel preserveror emptied beforestorage of 30 days or

longer. If adding a fuel preserver,fill the fuel tank with fresh

fuel. If only partially tiffed, air in the tank will promote fuel

deterioration during storage. If fuel preserver is not used,

drain the fuel tank, start the engine and let it run until the fuel

lines and carburetor are empty. Usefresh fuel next season.

SeeStoragefor additional information.

NEVERuse engine or carburetor cleaner products in the fuel

tank as permanent damagemay occur.

HighAltitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKi (89 RON)gasolineis acceptable.To

remainemissions compliant, high altitude adjustment is

required. Operationwithout this adjustment wiii cause

decreasedperformance, increasedfuel consumption, and

increasedemissions. Seea qualified Searsdealerfor high

altitude adjustment information. Operationof the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

Fresh Start@ Fuel Cap

The FreshStart@fuel cap (C) is designedto hold a

cartridge (D)which contains fuel preserver.Adding fuel

preserver helps keepfuel fresh and carburetors cleanfor

easierstarting all season long. TheFresh Start@fuel cap, if

equippedwith acartridge, automatically drips concentrated

fuel preserver into your fuel tank so you don't haveto add it

yourself.

NOTICE FreshStart@fuel preservercartridge is availableas

an optional accessory, retail item 7133386. it is not included

with the pressure washer. Contactthe original equipment

manufacturer, retailer, or dealerto obtain acartridge

designedfor the FreshStart@fuel cap installed on this

engine.

Readand follow all instructions and warnings given in the

FreshStart@fuel preserver cartridge package.

ConnectHoseandWater Supply to Pump

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

= Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

4. Runwater through garden hosefor 30 secondsto flush

it of debris. Turn off water.

NOTICE DONOTsiphon standing water for the water

supply. Use ONLYcold water (less than 100°F).

5. Connectgarden hose(not to exceed50 feet in length) to

water inlet. Tighten by hand.

NOTICE Removeand discard the shipping caps from the

pump's high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attachone end of hoseto

baseof spray gun. Tighten by hand.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERconnect high pressure hose to nozzleextension.

• Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

• Always becertain spray gun, nozzlesandaccessoriesare

correctly attached.

2. Attach other end of high pressure hoseto high pressure

outlet on pump. Tighten by hand.

Beforeconnectinggarden hoseto water inlet, inspect

inlet screen (A). Cleanscreen if it contains debris or have

it replacedif damaged.DONOTrunpressurewasher if

inlet screenis damaged or missing.

NOTICE Using a OneWay Valve (vacuumbreakeror check

valve) at pump inlet can cause pump or inlet connector

damage.

• ThereMUSTbeatleasttenfeetofunrestrictedgardenhose

betweenthepressurewasherinletandanydevice,suchasa

vacuumbreakeror checkvalve.

• Damageto equipment resulting from failure to follow this

instruction will void warranty.

A, WARNING Riskof eyeinjury.

Spray cansplash back or propel objects.

• Always wear indirect vented (chemical splash) safetygoggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

6. Turn ONthe water, press red button (B) on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

Checklist BeforeStarting Engine

Reviewthe unit to ensureyou haveperformed all of the

following:

1. Besure to readSafetyRules and Operationsections

before using the pressure washer.

2. Makesure handleis in placeand secure.

3. Checkthat oil has beenaddedto proper levelin engine

crankcase.

4. Add proper fuel to fuel tank.

5. Checkfor proper hoseconnections (high pressure and

water supply) and that there are no kinks, cuts, or

damageto the high pressure hose.

6. Provide proper water supply (not to exceed100%).

HOWTO USEYOURPRESSUREWASHER

If you haveanyproblems operating your pressure washer,

pleasecallthe pressure washer helpline at 1-800-222-3136.

PressureWasherLocation

PressureWasherClearance

_k WARNING Exhaustheat/gases can ignite

combustibles, structures or damagefuel tank

causing a fire.

• Keepat least5 ft. (152 cm) clearanceon all sides of pressure

washer including overhead.

Placepressure washer outdoors in an area that will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is kept awayfrom anywindows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in aconfined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

_k WARNING Runningenginegivesoff carbon

monoxide,an odorless, colorless, poisonous gas.

_ Breathing cancause headache,

carbon monoxide

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

• OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor runengineindoorsor in anenclosedarea,

evenifwindowsanddoorsareopen.

To Start YourPressureWasher

To start your engine-powered pressurewasherfor the first

time, follow these instructions step-by-step. This information

alsoapplies wheneveryou start the engine after you havelet

the pressure washer sit idle for at leasta day.

1. Placepressurewasher outside nearanwater source

capableof supplying water at a flow rate greaterthan

3.7 gallons per minute and no less than 20 PSi at

pressurewasher end of garden hose.

2. Checkthat high pressure hose is tightly connectedto

spray gun and pump. SeeAssembly for illustrations.

3. Makesure unit is in a levelposition.

4. Connectgarden hoseto water inlet on pressurewasher

pump.

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

• Damageto equipmentresultingfromfailureto followthis

instructionwill voidwarranty.

5. Turn ONthe water, press red button on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

6. Attach nozzleextension to spray gun. Tighten by hand.

|l ml I|

Pull backon collar of nozzleextension,insert selector

nozzleandreleasecollar. Tug on selector nozzleto make

sure it is securelyin place. See How to UseSelector

Nozzle.

8. Pushengine rocker switch (B) to on position (I or ON).

NOTICE Beforestarting the pressure washer, be sureyou

are wearing safety goggles asdescribed below.

_i, WARNING Riskof eyeinjury.

Spraycan splash backor propel objects.

• Always wear indirect vented (chemicalsplash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

NOTICE This unit is equipped with a ReadyStart® engine.A

ReadyStart® enginemeans there is no priming or choking

required.

9. Whenstarting engine, position yourself as

recommendedand grasp starter grip handle and pull

slowly until you feel some resistance.Then pull rapidly

to start engine.

_i, WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

_,_ arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVERpullstarter cord without first relieving spraygun

pressure.

• When starting engine, pull cord slowly until resistanceisfelt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, pressred button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

0. Return recoil starter slowly. DONOT let rope "snap

back" against starter.

11. Point spray gun in a safedirection, push the red button

to releasethe trigger lock, and pull the trigger.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

= DONOTallow CHILDRENto operatepressure washer.

= Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

= NEVERaim spraygun at people,animals, or plants.

= DO NOTsecure spray gun in open position.

= DO NOTleavespray gun unattendedwhile machineis running.

= NEVERuse aspray gun which does not havea trigger lock or

trigger guard in place andin working order.

= Always be certain spray gun, nozzlesandaccessoriesare

correctly attached.

_i, WARNING Contact with muffler area can result in

serious burns.

_ heat/gases can ignite

Exhaust

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipmentto cool beforetouching.

= Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

= It isa violation of California PuNic ResourceCode,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equippedwith a spark arrester,as defined in Section

4442, maintained ineffective working order. Otherstates or

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer,retailer, or dealer

to obtain a sparkarrester designedfor the exhaustsystem

installed onthis engine.

= Replacementparts must bethe same and installed inthe same

position as the original parts.

Howto StopYourPressureWasher

1. Release spray gun trigger and let engine idle for two

minutes.

Pushengine rocker switch to off position (0 or OFF).

ALWAYSpoint spray gun in a safe direction, push red

button and squeezespray gun trigger to releaseretained

high water pressure.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

= Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

NOTICE Spraygun traps high water pressure,evenwhen

engine is stopped and water is disconnected.

Howto UseAccessoryTray

The unit is equipped with an accessorytray with places to

store your spray gun and nozzleextension. Thereis also a

detachablehosewrap atthe back of the accessorytray to

hold your high pressure hose.

1. Placenozzleextensionand selector nozzlethrough hole

on accessorytray on left side of unit.

2. Placespray gun through hole on accessorytray on right

side of unit.

NOTICE You may also usethe spray gun holder on the

accessorytray to store your spray gun, nozzleextensionand

selector nozzleas shown in Featuresand Controls section.

3. Wrap high pressure hoseon hosewrap then attach hose

wrap to back of accessorytray.

4. Hook providedon back of accessorytray for safely

storing safety goggles.

Howto UseSelector Nozzle

Theselector nozzleallowsyou to switch betweenfive

different spray pattern nozzles.Spraypatterns can be

changedwhile pressurewasher is running once spray gun

trigger safety lock is engaged.The spray patterns vary as

shown below.

A, WARNING The high pressure stream of water that

this equipment produces cancut through skin

and its underlying tissues, leadingto serious

injury and possible amputation.

• NEVERchangespraypatternswithoutthetriggerlockedonthe

spraygun.

• DONOTtwist selectornozzlewhilespraying.

Followtheseinstructionsto changenozzlepatterns:

1. Select desiredspray pattern:

* MAX- Forstubborn or hard to reachsurfacesuch

assecond story surfaces, paint removal,oil stains,

rust removal or other stubborn substances(tar,

gum, grease,wax, etc.).

GENERAL- For most all purposecleaning such as

home siding, brick patios, wood decks, driveways

and sidewalks, garagefloors, etc..

DELICATE- Forgentle cleaningof cars/trucks,

boats, RV's, patiofurniture, lawn equipment, etc..

FLUSH- Forquick high flow clean up and long

reachcleaning of second story siding and windows.

SOAP- Forgeneral soapapplications or to launch

soapto second story siding and windows.

2. Push button on selector nozzle,nozzledial will pop up.

3. Turndial until desired spray pattern lines up with button

on selector nozzle.

4. Push dial in untilitlocks into place.

UsageTips

* For most effective cleaning, keepselector nozzlefrom

8 to 24 inches (20 to 61 cm) away from cleaning surface.

If you get selector nozzletoo close, especiallyusing a

high pressure spray pattern nozzle,you may damage

surface being cleaned.

DONOTget closer than 6 inches (15 cm) when cleaning

tires.

2-1N-1SoapSystem

_i, WARNING Chemical Burn Hazard.

_-_ Chemicalscould cause bodily injury, property

damageor death.

• DONOTusecausticliquidwithpressurewasher.

• Use ONLYpressurewasher safe detergents/soaps. Follow all

manufacturers instructions.

Cleaning and Applying Detergentwith the

Project Pro® PerfectMW MSiphon

To apply undiluted detergent using the blue

PerfectMixTM siphon,follow these steps:

1. Reviewuse of selector nozzle.

2. Attach PerfectMixTM siphon hoseto

pump and PerfectMixTM concentrate

bottle.

NOTICE Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the siphon into a detergent solution bottle, route

the tube so asto keepit from inadvertently contacting the hot

muffler.

3. Make sure SOAPspray pattern nozzleis selectedon

selector nozzle.

NOTICE Detergentcannot be applied with the MAX,

GENERAL,DELICATEor FLUSHspray pattern nozzles.

4. Make sure garden hose is connectedto water inlet.

Checkthat high pressure hoseis connected to spray gun

and pump. Turn on water.

NOTICE You must attach all hoses before you start the

engine.

• Starting the engine without all the hoses connected and without

the water turned ONwill damagethe pump.

• Damageto equipment resulting from failure to follow this

instruction will void warranty.

5. Start enginefollowing instructions How to Start Your

Pressure Washer.

6. Apply detergent to a dry surface, starting at lower

portion of areato bewashedandwork upward, using

long, even,overlapping strokes.

7. Allow detergent to "soak in"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergentto dry on

(prevents streaking).

Cleaning and Applying Detergentwith

the Standard Clear Siphon /__

To apply diluted detergent using the

standard clearsiphon tube, follow these

steps:

1. Reviewuseof selector nozzle.

2. Attach clear siphon hoseto barbedfitting on pump.

3. Mix detergent solution as required by job.

4. Placesmall filter end of clear siphoning tube into

container with diluted solution as described above.

NOTICE DONOTinsertstandard siphon hose in Extreme

Concentrate.Failureto dilute concentratewill causeexcessive

application and consumption of solution.

NOTICE Makesure the filter is fully submerged in fluid

while applying solution.

NOTICE Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the siphon into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot

muffler.

5. Makesure SOAPspray pattern nozzleis selectedon

selector nozzle.

NOTICE Detergentcannot be applied with the MAX,

GENERAL,DELICATEor FLUSHspray pattern nozzles.

6. Makesure garden hoseis connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE You must attach all hoses before you start the

engine.

• Starting the engine without all the hoses connected andwithout

the water turned ONwill damagethe pump.

• Damageto equipment resultingfrom failure to follow this

instruction will void warranty.

7. Start engine following instructions How to Start Your

Pressure Washer.

8. Apply detergentto adry surface, starting at lower

portion of areato bewashed and work upward, using

long, even, overlappingstrokes.

9. Allow detergent to "soakin"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergent to dry on

(prevents streaking).

NOTICE You must flush the detergent siphoning system

after eachuse by placing the filter into a bucketof clean

water, then run the pressurewasher in low pressure for 1-2

minutes.

PressureWasherRinsing

ForRinsing:

1. Select and changeto desired spray pattern nozzleon

selector nozzle.SeeHow To UseSelector Nozzle.

2. Keepspray gun a safedistance from areayou plan to

spray.

_i, WARNING Kickback from spray gun can cause you to

fall.

• Operatepressure washer from astable surface.

• Beextremely careful if you must usethe pressure washer from

a ladder,scaffolding, or any other similar location.

• Firmly grasp spray gun with both handswhen using high

pressure sprayto avoid injury when spray gun kicks back.

3. Apply a high pressure spray to a small area and then

checksurface for damage, if no damageis found, you

can assumeit is okay to continue rinsing.

4. Start attop of areato be rinsed, working down with

same overlapping strokes asyou used for cleaning.

Cleaning DetergentSiphoningTube

If you usedthe clear detergent siphoning tube, you must

flush it with cleanwater before stopping the engine.

1. Placedetergent siphoning tube/filter in a bucket full of

cleanwater.

2. Select and changeto SOAPspray pattern nozzleon

selector nozzle.SeeHow To UseSelector Nozzle.

3. Flush for 1-2 minutes.

4. Shut off engine following instructions How to Stop

Pressure Washerand turn off water supply.

5. ALWAYSpoint spray gun in a safe direction push red

button and squeezespray gun trigger to releaseretained

high water pressure.

NOTICE Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Automatic Cool DownSystem(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125°F.The systemengagesto cool the pump by discharging

the warm water onto the ground.

ENGINETECHNICALiNFORMATiON

This is a single cylinder, overheadvalve (OHV), air cooled

engine, it is a low emissions engine.

In the State of California, Model 120000 enginesare certified

by the California Air Resources Boardto meet emissions

standardsfor 125 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respectto the performanceor

operational life of this engine.Theengine is warranted solely

according to the product and emissions warranties stated

elsewherein this manual.

Power Ratings

Thegross power rating for individual gas engine models is

labeled in accordancewith SAE(Society of Automotive

Engineers)codeJ1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been

obtained and corrected in accordancewith SAEJ1995

(Revision 2002-05). Torquevalues are derived at 3060 RPM;

horsepower values are derived at 3600 RPM.Actual gross

engine power will be lower and is affected by, among other

things, ambient operating conditions and engine-to-engine

variability. Givenboth the wide arrayof products on which

enginesare placed andthe variety of environmental issues

applicableto operatingthe equipment,the gas engine wiii not

developthe ratedgross power when used in a given pieceof

power equipment (actual "on-site"or net power). This

difference is due to a variety of factors including, but not

limited to, accessories(air cleaner, exhaust, charging,

cooling, carburetor, fuel pump, etc.), application limitations,

ambient operating conditions (temperature, humidity,

altitude), and engine-to-enginevariability. Dueto

manufacturing and capacity limitations, Briggs & Stratton

may substitute an engine of higher ratedpower for this

Seriesengine.

PRODUCTSPECIFICATIONS

PressureWasherSpecifications

Max Outlet Pressure ...................... 3,000 PSI*

Max Flow Rate............................. 2.7 GPM

DetergentMix ........................ Use asdirected

Water SupplyTemperature .......... Not to exceed100%

EngineSpecifications

Bore ................................. 2.69 in. (68mm)

Stroke ............................... 2.04 in. (52mm)

Displacement ........................ 11.58in. (190cc)

SparkPlug

Type:...................... Briggs & Stratton 692051

SetGapTo: ...................... 0.020inch (0.50mm)

ArmatureAirGap:........... 0.010-0.014in.(0.25-0.36mm)

Valveclearancewith valvesprings installedand piston 1/4 in.

(6 mm) pasttop deadcenter(checkwhenengineiscold).

Intake.................... 0.004-0.008in.(0.10-0.20mm)

Exhaust .................. 0.004-0.008in.(0.10-0.20mm)

FuelCapacity............................... 1.6Quarts

0il Capacity........................ 20 Ounces(0.6 liter)

NOT/CE Forpractical operation, the engine load should not

exceed85% of ratedpower. Enginepower will decrease

3-1/2% for each1,000 feet (300 meters) above sealeveland

1% for each 10° F(5.6° C) above77° F(25° C). It should

operatesatisfactorily at an angle up to 15°.

* This pressure washer is ratedin accordanceto the

PressureWasherManufacturersAssociation (PWMA)

standard PW101(Testing and Rating Performanceof

PressureWashers).

OWNER'SRESPONSiBiLiTiES

Follow the hourly or calendarintervals, whichever occurs

first. More frequent service is required when operating in

adverseconditions noted below.

iiiiiiiiiiiiiiiiiiiiiiii_iiiii_iiiiiiiJii!iiiiiiiiiiiiJiJiiiiiiiiiiiiiJiiJiiiHH_iiiJiiiiiii_iiiii!iii_ii_iii_:_:_iiiiW_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

• Changeengine oil

• Check/clean water inlet screen'

* Checkhigh pressure hose

* Checkdetergentsiphoning hoses

, Checkspray gun and assembly for leaks

, Cleandebris

, Checkengineoil level

, Cleanengine air cleaner_

, Changeengine oil_

, inspect muffler andsparkarrester

iiiiii J

, Replaceengine air cleaner_

, Replacespark plug

, Cleancooling system_

Clean if clogged. Replace if perforated or torn.

2Service more often under dirty or dusty conditions.

GeneralRecommendations

Regularmaintenancewill improve the performanceand

extendthe life of the pressurewasher. Seeany Searsor

other qualified service dealerfor service.

Thepressure washer warranty does not cover items that

havebeensubjected to operator abuseor negligence.To

receivefull valuefrom the warranty, the operator must

maintain pressurewasher as instructed in this manual

including proper storage asdetailed in Storage.

Someadjustments will needto be made periodically to

properly maintain your pressurewasher.

All service and adjustments should be madeat least once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTICE Oncea yearyou should cleanor replacethe spark

plug and replacethe air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and helpyour engine run

better and last longer.

PumpOil

DONOTattemptany oil maintenanceon this pump. The

pump is pre-iubricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

EmissionsControl

Maintenance,replacement,or repair of the emissions

controldevices and systemsmay be performed byany non-

roadengine repair establishment or individual. However,

to obtain "no charge" emissions control service, the work

must be performed by a factory authorizeddealer. Seethe

Emissions Warranty.

Before EachUse

1. Checkengine oil level.

2. Cleandebris.

3. Checkwater inlet screenfor damage.

4. Checkhigh pressure hose for leaks.

5. Checkgun and nozzleextension assemblyfor leaks.

6. Purge pump of air and contaminants.

PRESSUREWASHERMAINTENANCE

CleanDebris

Daily or before use, cleanaccumulateddebris from pressure

washer. Keeplinkage, spring and controls clean. Keeparea

around and behind muffler free from any combustible debris.

inspect cooling air slots and openings on the pressure

washer. Theseopenings must be kept clean and

unobstructed.

Pressurewasherparts should be kept cleanto reducethe

risk of overheating and ignition of accumulated debris.

• Usea damp cloth to wipe exterior surfaces clean.

NOTICE improper treatment of pressurewasher can

damageit and shorten its life.

• DONOTinsertanyobjectsthroughcoolingslots.

• Usea soft bristle brush to loosencaked on dirt, oil, etc.

• Useavacuum cleanerto pick up loosedirt and debris.

CheckandClean Inlet Screen

Examinegarden hoseinlet screen. Cleanif it is clogged or

replaceif it is torn.

CheckHighPressure Hose

High pressure hoses candevelop leaksfrom wear,kinking,

or abuse, inspect hose beforeeachuse. Checkfor cuts,

leaks,abrasions,bulging of cover, or damageor movement

of couplings. If anyof these conditions exist, replacehose

immediately.

_lLWARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

, NEVERrepairhighpressurehose.Replaceit.

• ReplacementhoseratingMUSTexceedmaximumpressure

ratingof unit.

CheckSprayGunandNozzleExtension

Examinehoseconnectionto spraygun and makesureitis

secure.Testtrigger bypressingit and makingsureit springs

backintoplacewhenyou releaseit. Donotdepressredbutton

andtesttrigger.Youshouldnot beableto presstrigger.Replace

spraygunimmediatelyif it fails anyof thesetests.

Selector NozzleMaintenance

A pulsing sensationfelt while squeezingthe spray gun trigger

may be causedby excessivepump pressure.Theprincipal

causeof excessivepump pressureis a nozzleclogged or

restricted with foreign materials, such asdirt, etc. To correct

the problem, immediately cleanthe nozzlesfollowing these

instructions:

1. Shut off engine and turn off water supply.

2. ALWAYSpoint spray gun in a safe direction, press red

button and and squeezespray gun trigger to release

retainedhigh water pressure.

_lLWARNING The high pressure stream of water that

this equipment produces cancut through skin

and its underlying tissues, leadingto serious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

* Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

* ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Removeselector nozzlefrom endof nozzleextension.

Use a small paper clip to free anyforeign material

clogging or restricting each nozzle(A) in the selector

nozzle.

Removenozzleextensionfrom spray gun.

Using a garden hose, remove additional debris by back

flushing water through nozzleextension. Backflush

between 30 to 60 seconds.

7. Reinstall selector nozzleinto nozzleextension.

8. Reconnect nozzleextensionto spray gun.

9. Make sure garden hose is connectedto water inlet.

Checkthat high pressure hoseis connected to spray gun

and pump. Turn on water.

10. Start enginefollowing instructions How to Start Your

Pressure Washer.

11. Test pressurewasher by operating in eachspray pattern.

O-Ring Maintenance

Purchasean O-Ring RepairKitat your localSearsor bycalling

1-800-4-1VlY-HOIVlE(469-4663) or online atwww.sears.com,it

is notincludedwith thepressurewasher.This kit includes

replacemento-rings,rubberwasherandwater inletfilter. Referto

the instructionsheetprovidedin thekit to serviceyour unit's

o-rings.

A. WARNING The highpressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

* NEVERrepairleakingconnectionswithsealantofanykind.

Replaceo-ringorseal.

ENGINEMAINTENANCE

A. WARNING Unintentional sparking can result in fire or

_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTOYOUR PRESSURE

WASHER

* Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

* Useapproved spark plug tester.

* DONOTcheckfor sparkwith spark plug removed.

Oil

Oil Recommendations

We recommendthe use of Briggs & Stratton Warranty

Certifiedoils for best performance. Other high-quality

detergent oils are acceptableif classified for serviceSF,SG,

SH,SJ or higher. DONOTusespecial additives.

Outdoortemperatures determine the proper oil viscosity for

the engine.Usethe chartto selectthe best viscosity for the

outdoor temperature range expected.

104___506886 _coo__

32 .o

-4

-22

\ 40

;_30

_°_20

_m m 0

--_C °

-20

-30

* Below40°F(4°C)the useofSAE30will resultin hardstarting.

** Above80°F(27°C)theuseof 10W30maycauseincreasedoil

consumption.Checkoil levelmorefrequently.

NOTICE Synthetic oil meeting ILSACGF-2,API

certification mark and APIservice symbol with

"SJ/0F ENERGYCONSERVING"or higher, is an

acceptableoil at all temperatures. Useof synthetic oil

does not alter required oil changeintervals.

CheckingOilLevel

1. Make sure pressure washer is on a levelsurface.

2. Removeoil dipstick and wipe dipstick with clean cloth.

Replaceandtighten dipstick. Removeand and check oil

level.

3. Verify oil is at FULL mark (top hole) on dipstick. Replace

and tighten dipstick.

Full

Adding Engine Oil

1. Make sure pressure washer is on a levelsurface.

2. Checkoil levelas described in CheckingOilLevel

3. If needed,slowly pour oil into oil fill opening to the FULL

mark on dipstick. DONOToverfill.

4. Tip your pressure washer to drain oil from oil fill into a

suitable container making sureyou tip your unit away

from spark plug. When crankcaseis empty, return

pressurewasher to upright position.

5. Slowly pour recommendedoil (about 20 oz. (0.6 I)) into

oil fill opening. Pauseto permit oil to settle. Fillto Full

mark on dipstick.

6. Wipe dipstick cleaneachtime oil level is checked. DO

NOToverfill.

7. Replaceand tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnectspark plug wire to spark plug.

ServiceAir Cleaner

Your engine will not run properly and may be damagedif you

run it with a dirty air cleaner. Service more often if operating

under dirty or dusty conditions. Replacementsare available

atyour local Searsservicecenter.

To servicethe air cleaner, follow thesesteps:

1. Loosenfastener (A) and remove air cleanercover (B).

NOTICE Overfilling with oil may cause the engine to not

start, or hard starting.

• DO NOToverfill.

• If overthe FULLmark on dipstick, drain oil to reduceoil level to

FULLmark on dipstick.

4. Replaceandtighten dipstick.

Changing Engine Oil

if you are usingyour pressurewasher under extremely dirty

or dusty conditions, or in extremely hot weather, changeoil

more often.

_lLCAUTION Avoid prolonged or repeatedskin contact

with usedmotor oil.

• Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

• Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil while engine is still warm from running,as

follows:

1. Drain fuel tank by running pressure washer until fuel

tank is empty.

2. Disconnect spark plug wire and keepit away from spark

plug.

3. Cleanarea around oil fill, removeoil fill cap/dipstick.

Wipe dipstick clean.

2. Removeair cleaner (C)from base(D).

3. To loosendebris, gently tap air cleaneron a fiat surface.

If excessivelydirty, replacewith a newair cleaner.

4. Install the air cleanerinto the base. Makesure air

cleanerfits securelyin the base.

5. Install cover and securewith fastener. Make sure

fastener is tight.

NOTICE You can purchasenew air filter elements by calling

1-800-4-1VlY-HOIVlE(469-4663).

ServiceSparkPlug

Changingthe spark plug will help your engine to start easier

and run better.

1. Cleanareaaround spark plug.

2. Removeand inspect spark plug.

3. Replacespark plug if electrodes are pitted, burned or

porcelain is cracked. Usethe recommendedreplacement

plug. See Specifications.

Checkelectrode gap with wire feeler gaugeand reset

spark plug gap to recommended gap if necessary(see

Specifications).

5. install spark plug and tighten firmly.

NOT/CE You can purchase a new spark plug by calling

1-800-4-iVlY-NOiVlE(469-4663).

inspectiVlufflerand SparkArrestor

inspectthe mufflerfor cracks,corrosion, or otherdamage.

Removethe spark arrester,if equipped,and inspectfor

damageor carbonblockage,if replacementparts are required,

makesureto useonly original equipmentreplacementparts.

A, WARNING Contact with muffler area can result in

serious burns.

_ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOID hot exhaust gases.

• Allow equipmentto cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sidesof

pressure washer including overhead.

• It isa violation of California Public Resource Code,Section

4442, to use or operatethe engine on anyforest-covered,

brush-covered,or grass-covered land unlessthe exhaust

system is equippedwith aspark arrestor,as definedin Section

4442, maintained ineffectiveworking order. Otherstates or

federal jurisdictionsmay havesimilar laws.

Contactthe original equipment manufacturer,retailer, or dealer

to obtain a sparkarrestor designedfor the exhaustsystem

installedon this engine.

• Replacementparts must bethe sameand installed in the same

position as the original parts.

Air CoolingSystem

Overtime debris may accumulate in cylinder cooling fins and

cannot be observedwithout partial engine disassembly. For

this reason,we recommendyou havea qualifiedSears

servicedealer cleanthe cooling system per recommended

intervals (see MaintenanceSchedule). Equallyimportant is to

keeptop of engine freefrom debris. See CleanDebris.

Carburetor Adjustment

Thecarburetor on this engine is low emission. It is equipped

with a non-adjustable idle mixture valve.Top speedhas been

set at the factory. If adjustment is required,seean authorized

servicedealer.

_IL CAUTION Excessively high operating speeds increase

risk of injury and damage to pressure washer.

Excessively low speeds impose a heavy load.

• DO NOTtamper with governedspeed.Pressurewasher

supplies correct ratedfrequency and voltage when running at

governedspeed.

• DO NOTmodify pressure washer in any way.

AFTEREACHUSE

Water should not remain in the unit for long periods of time.

Sedimentsor minerals candeposit on pump parts and

"freeze" pump action. Follow these procedures after every

use:

1. Shut off engine,turn off water supply, point gun in a

safedirection, press red button and squeezetrigger to

relievetrapped pressure and let engine cool.

_ILWARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Disconnecthose from spray gun and high pressure

outlet on pump. Drainwater from hose,gun, and spray

tip extension. Usea ragto wipe off the hose.

Empty pump of aii pumped liquids by puffing recoil

handleabout 6 times. This should remove most liquid in

pump.

Coilhigh pressure hoseon hosewrap provided on

accessorytray.

Store unit in a clean, dry area.

If storing for more than 30 days see Long Term Storage

on next page.

_ILWARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosion can causesevere burns

or death.

WHENSTORINGFUELOREQUIPMENTWITHFUELINTANK

* Storeawayfrom furnaces,stoves,waterheaters,clothes

dryers,or otherappliancesthathavepilotlightor other

ignitionsourcebecausetheycanignitefuelvapors.

Page is loading ...

Craftsman 580752581 Owner's manual

Brand: Craftsman

Model: 580752581

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580.752581

Download PDF

report

in other languages

español: Craftsman 580752581 El manual del propietario

Craftsman 580752581 Owner's manual

This manual is also suitable for

Craftsman 580752581 Owner's manual

in other languages

Related papers

Other documents