Lindy 43063 User manual

Category
Cable assembly tools
Type
User manual

Lindy 43063 is a remarkable HDMI DIY set that empowers you to create custom HDMI cables with ease. This versatile tool enables you to terminate HDMI cables professionally, making it ideal for custom installations, repairs, or replacements. With its user-friendly design and clear instructions, the Lindy 43063 is perfect for both experienced installers and DIY enthusiasts.

Lindy 43063 is a remarkable HDMI DIY set that empowers you to create custom HDMI cables with ease. This versatile tool enables you to terminate HDMI cables professionally, making it ideal for custom installations, repairs, or replacements. With its user-friendly design and clear instructions, the Lindy 43063 is perfect for both experienced installers and DIY enthusiasts.

HDMI DIY SET
English
Manual
English
Step 1: Strip Cable
(1) Strip cables Jacket 30mm. Cut the braid and aluminum, but keep the drain wire.
(2) Strip 20mm of the aluminum foil from twisted pairs (TP) with blue foil for the TMDS data.
Strip 24mm of the aluminum foil from twisted pair with silver foil for Ethernet and Audio Return Channel (HEAC).
It is important that this foil length is just 6mm in order to ensure easy installation in the following steps.
Step 2: Insert Wires
(1) Arrange the wires for 10-hole holder per the pin assignment in the next page, cut the wires at an angle for easy
insertion
(2) Insert the wires into 10-hole holder in one step. You can divide 10 wires into two groups and insert them in two
steps before you are skillful.
(3) Arrange the wires for 9-hole holder and insert the wires into the holder. It is very IMPORTANT to keep two
holders in alignment.
Patentierte Stecker und Hand-Werkzeug, alle Rechte vorbehalten. Patented connector and hand tool, all rights reserved.
English
Pin Assignment
Any mis-wiring, even an intercrossing of Twisted Pairs, will lead to transmission failure.
So it is EXTREMLY VITAL to make sure the wire assignment correct without any error!
Patentierte Stecker und Hand-Werkzeug, alle Rechte vorbehalten. Patented connector and hand tool, all rights reserved.
English
Step 3: Compress
(1) Install the HDMI connector in the mounting piece.
(2) Press the two holders into the mounting piece.
The blue 10-hole holder is for 10-pin side of HDMI connector and the green 9-hole holder for 9-pin side.
Press the two holders with your thumb until they lock with the connector.
(3) Insert the assembly into the hand tool.
(4) Compress the tool.
(5) Finished! Excessive wires are cut out automatically.
Patentierte Stecker und Hand-Werkzeug, alle Rechte vorbehalten. Patented connector and hand tool, all rights reserved.
English
Step 4: Install Shell
(1) Insert the connector into the bottom half of metal case.
(2) Install the metal band to make a tension relief. Making sure that the shield drain wire is crimped under the band
to achieve a continuous shielding!
(3) Install the upper half of the housing and connect them using the two screws. Make sure that no wires are
pinched!
(4) Check the cable with the HDMI Cable tester.
Important Note
Please use our specially designed HDMI cables
We have no guarantee that this connector works with the cables other than our cables.
Patentierte Stecker und Hand-Werkzeug, alle Rechte vorbehalten. Patented connector and hand tool, all rights reserved.
English
HDMI Cable Portable Tester
HDMI cable portable tester is designed for professional HDTV installation, especially for DIY termination in the field.
With this portable device, the installers can quickly test, troubleshoot and verify HDMI cables.
Equipped with dual modes, CONTINUITY and SWEEP, the tester can either test the DC connectivity or sweep the pins
one by one and detect the intercrossed adjacent pins which are beyond the common single continuity testers on the
market.
Usage
Continuity Mode:
In this mode, the device can test the continuity of each wire inside HDMI cable. Please see the table for pin and wire
assignment in our solderless HDMI DIY System.
Sweep Mode:
If the cable passes the continuity test but does not work on a real DVD-TV system, you can use the SWEEP mode to
sweep all pins one by one sequentially for any intercross. This kind of fatal problem sometimes occurs with the
adjacent wires of a twisted pair in field termination, but is always beyond common DC continuity tester.
Sweep Test procedure:
(1) Switch the tester to SWEEP mode, the LEDs on the master unit (transmitter) will light serially on each column;
(2) Insert one plug of the cable into master unit (transmitter);
(3) Insert the other plug into the remote unit (receiver)
(4) Check the LED lightning sequence on the remote unit (receiver). The reserved LEDs show intercrossed pins.
(5) Three examples:
Correct False False
Patentierte Stecker und Hand-Werkzeug, alle Rechte vorbehalten. Patented connector and hand tool, all rights reserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Lindy 43063 User manual

Category
Cable assembly tools
Type
User manual

Lindy 43063 is a remarkable HDMI DIY set that empowers you to create custom HDMI cables with ease. This versatile tool enables you to terminate HDMI cables professionally, making it ideal for custom installations, repairs, or replacements. With its user-friendly design and clear instructions, the Lindy 43063 is perfect for both experienced installers and DIY enthusiasts.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI