Bushwacker 49526 Installation guide

Brand
Bushwacker
Model
49526
Type
Installation guide

This manual is also suitable for

Bushwacker 49526 is a set of bed rail caps designed to fit your Chevy Silverado Short Bed. These caps are made from durable TPO plastic and are designed to protect your truck's bed rails from scratches, dents, and other damage. They are also paintable, so you can match them to your truck's exterior color.

Features:

  • Durable TPO plastic construction
  • Protects bed rails from scratches, dents, and other damage
  • Paintable to match your truck's exterior color
  • Easy to install with included hardware

Possible Use Cases:

  • Protecting your truck's bed rails from everyday wear and tear

Bushwacker 49526 is a set of bed rail caps designed to fit your Chevy Silverado Short Bed. These caps are made from durable TPO plastic and are designed to protect your truck's bed rails from scratches, dents, and other damage. They are also paintable, so you can match them to your truck's exterior color.

Features:

  • Durable TPO plastic construction
  • Protects bed rails from scratches, dents, and other damage
  • Paintable to match your truck's exterior color
  • Easy to install with included hardware

Possible Use Cases:

  • Protecting your truck's bed rails from everyday wear and tear
6710 N CATLIN AVE. • PORTLAND, OR 97203 • 503-283-4335 • 1-800-234-8920 (USA AND CANADA) • FAX 503-283-3007
Bushwacker only approves installing the bed rail caps according to
these written instructions with the hardware provided. WARNING:
Failure to install according to these instructions will invalidate
the warranty. This includes, but is not limited to, using alternative
installation methods, hardware, or materials. DO NOT USE: Loctite,
SuperGlue, or similar products on the hardware or the parts.
Fit: Bed rail caps should be held to the vehicle surface to verify
correct type and fi t BEFORE beginning installation or painting.
Small fi t adjustments can be made by trimming (fi ling, sanding, or
cutting) excess plastic.
When using this product with other aftermarket accessories, like Tonneau
Covers or Toppers, you must allow for lengthwise expansion and contraction
of the bed rail cap. You must notch around any clamps or hard fastening
points.
Painting: (Optional) If paint is desired it must be done prior to installation.
Sand (optional) before application of paint. Clean outer surface with a good
grade degreaser. DO NOT USE LACQUER THINNER OR ENAMEL
REDUCER AS A DEGREASER. Wipe outer surface thoroughly with a tack
rag prior to paint. Application of plastic adhesion promoter for TPO plastic
as per your paint system manufacturer’s recommendations is required.
Paint caps using a high quality enamel, or polyurethane automotive paint.
Application of a primer coat is optional.
Preparing the Work Area: Clean the area of installation with a
cloth and rubbing alcohol or prep-solvent to remove any car wax or
dirt from vehicle surface.
Ambient Temperature: During installation the vehicle, bed rail
caps, and the tape needs to be between 60°F and 110°F for proper
adhesion. Failure to maintain proper installation temperature may
result in the part not functioning correctly. If not within acceptable
range, increase surface temperature using a heat gun or suitable
device (hair dryer) to help reach proper range. The warmer the
surface, the better the bond.
STEP 1 – PRIOR TO INSTALLATION
A)
B)
C)
D)
E)
F)
Chevy Silverado Short Bed
Bed Rail Cap
Clean Cloth
Rubbing Alcohol
#2 Phillips Screw Driver
SW1-0050, 10
x 5/16 Truss
Phillips Screw,
4 pcs
CL1-0006, “S”
Spring Clip,
4 pcs
Set Part #49519
Rev-0 10-29-10
TOOLS FOR EASY INSTALLATION:
•
•
•
To claim a warranty, you must provide Proof
of Purchase.
LIMITED LIFETIME WARRANTY AGAINST
ANY MANUFACTURING DEFECTS
•
1. 2.
Included in Hardware Kit:
6710 N CATLIN AVE. • PORTLAND, OR 97203 • 503-283-4335 • 1-800-234-8920 (USA AND CANADA) • FAX 503-283-3007
Bed Rail Cap Installation
Peel the red vinyl backing away from the pieces of
tape on the inside of the bed rail cap.
Position the bed rail cap snugly at the tail end of the
bed rail.
Carefully lay the part down on the bed rail (aligning the stake
pocket holes in the part with the stake pockets in the truck if
applicable) and apply 30 PSI to the taped areas for proper
bond. See Illustration A
Wait one hour, making sure vehicle maintains proper
temperature, and apply 30 PSI to the taped areas
AGAIN for proper adhesion to the vehicle. NOTE:
Tape reaches maximum adhesive bond after 24
hours of contact.
Slide a CL1-0006, “S” Spring Clip, onto the bed rail in
the areas where there is a bump on the inside edge
of the bed rail cap. See Illustration B & C
Fasten the bed rail cap to the clips with the SW1-
0050, 10 x 5/16 Truss Phillips Screw. See Illustration
B & C
1.
2.
3.
4.
5.
6.
Optional Stake
Pocket Hole
Illustration A
Illustration B
Illustration C
Bed Rail Cap
Bed Rail
Tape
  • Page 1 1
  • Page 2 2

Bushwacker 49526 Installation guide

Brand
Bushwacker
Model
49526
Type
Installation guide
This manual is also suitable for

Bushwacker 49526 is a set of bed rail caps designed to fit your Chevy Silverado Short Bed. These caps are made from durable TPO plastic and are designed to protect your truck's bed rails from scratches, dents, and other damage. They are also paintable, so you can match them to your truck's exterior color.

Features:

  • Durable TPO plastic construction
  • Protects bed rails from scratches, dents, and other damage
  • Paintable to match your truck's exterior color
  • Easy to install with included hardware

Possible Use Cases:

  • Protecting your truck's bed rails from everyday wear and tear
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents