Noble House 305420 Installation guide

Brand
Noble House
Model
305420
Type
Installation guide

This manual is also suitable for

Label Picture Descri
p
tion QT
Y
A Seat 1
B Right Armrest 1
C Left Armrest 1
D Backrest 1
E Back Cushion 1
F Seat Cushion 1
Caution : You must read this before you proceed
Chair
Noble house Home Furnishings LLC Page 1 OF 5
Label Picture Description QTY
①
Bolt (M6*15MM) 3
② Bolt (M6*20MM) 5
③ Bolt (M6*25MM) 5
④
Bolt (M6*35MM) 3
⑤ Allen Key 1
This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Chair parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the parts
and steps before assembly.
Before
Beginnin
g
Assembly
:
Overview
FRONT FACING
X3
Seat(A)
X5
X
3
Left Armrest(C)
Backrest(D)
Back Cushion(E)
Seat Cushion(F)
Right Armrest(B)
X5
X1
Noble house Home Furnishings LLC Page 2 OF 5
Open the carton and place all the parts onto a clean, non-marring surface.
1.1) Attach Seat(A) to Right Armrest(B) using Bolts(②) with Allen Key(⑤) as shown above.
1.2) Attach Seat(A) to Right Armrest(B) using Bolts(③) with Allen Key(⑤) as pictured.
Do not fully tighten the Bolts.
Align Backrest(D) to Right Armrest(B) and Seat(A).
2.1) Attach Backrest(D) to Seat(A) using Bolts(④) with Allen Key(⑤) as shown above.
2.2) Attach Backrest(D) to Right Armrest(B) using Bolt(①) with Allen Key(⑤) as pictured.
Do not fully tighten the Bolts.
Step 1
Step 2
1.1
1.2
2.1
2.2
Noble house Home Furnishings LLC Page 3 OF 5
Put Seat Cushion(F) and Back Cushion(E) on the Chair.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
3.1) Attach Seat(A) to Left Armrest(C) using Bolts(②) with Allen Key(⑤) as shown above.
3.2) Attach Seat(A) to Left Armrest(C) using Bolts(③) with Allen Key(⑤) as pictured.
3.3) Attach Backrest(D) to Left Armrest(C) using Bolt(①) with Allen Key(⑤) as pictured.
Do not fully tighten the Bolts.
Place the Chair on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and carefully sit onto the Chair, this will help to align all parts at all joints.
Then get off the Chair, and in a sequential manner, proceed to tighten all Bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one, this may cause the
frame to warp.
If there are still wobbles, loosen the Bolts and execute this same process.
Note: This step is done best with the assistance of a second adult.
Step 3
Step 4
Step 5
Back Cushion(E)
Seat Cushion(F)
3.1
3.2
3.3
Noble house Home Furnishings LLC Page 4 OF 5
Noble house Home Furnishings LLC Page 5 OF 5
Label Picture Description QTY
G Seat 1
H Right Armrest 1
I Left Armrest 1
J Backrest 1
E Back Cushion 2
F Seat Cushion 2
Caution : You must read this before you proceed
Loveseat
Noble house Home Furnishings LLC Page 1 OF 5
Label Picture Descri
p
tion QT
Y
① Bolt (M6*15MM) 3
② Bolt (M6*20MM) 5
③ Bolt (M6*25MM) 5
④ Bolt (M6*35MM) 4
⑤ Allen Key 1
Before
Beginnin
g
Assembly
:
Overview
This Loveseat has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Loveseat parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.
FRONT FACING
X3
X5
X4
Seat(G)
X5
X1
Right Armrest(H)
Left Armrest(I)
Backrest(J)
Back Cushion
(
E
)
Seat Cushion(F)
Noble house Home Furnishings LLC Page 2 OF 5
Align Backrest(J) to Right Armrest(H) and Seat(G).
2.1) Attach Backrest(J) to Seat(G) using Bolts(④) with Allen Key(⑤) as shown above.
2.2) Attach Backrest(J) to Right Armrest(H) using Bolt(①) with Allen Key(⑤) as pictured.
Do not fully tighten the Bolts.
Step 1
Open the carton and place all the parts onto a clean, non-marring surface.
1.1) Attach Seat(G) to Right Armrest(H) using Bolts(②) with Allen Key(⑤) as shown
above.
1.2) Attach Seat(G) to Right Armrest(H) using Bolts(③) with Allen Key(⑤) as pictured.
Do not fully tighten the Bolts.
Step 2
1.1
1.2
2.1
2.2
Noble house Home Furnishings LLC Page 3 OF 5
Step 3
3.1) Attach Seat(G) to Left Armrest(I) using Bolts(
②
) with Allen Key(
⑤
) as shown above.
3.2) Attach Seat(G) to Left Armrest(I) using Bolts(③) with Allen Key(⑤) as pictured.
3.3) Attach Backrest(J) to Left Armrest(I) using Bolt(①) with Allen Key(⑤) as shown
above.
Do not full
y
ti
g
hten the Bolts.
Step 4
Place the Loveseat on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and carefully sit onto the Loveseat, this will help to align all parts at all joints.
Then get off the Loveseat, and in a sequential manner, proceed to tighten all Bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one, this may cause the
frame to warp.
If there are still wobbles, loosen the Bolts and execute this same process.
Note: This step is done best with the assistance of a second adult.
Step 5
Put Seat Cushions(F) and Back Cushions(E) on the Loveseat.
Your Loveseat is ready for use.
This Loveseat can only be used on a flat, level surface.
Seat Cushion(F)
Back Cushion(E)
3.1
3.2
3.3
Noble house Home Furnishings LLC Page 4 OF 5
Noble house Home Furnishings LLC Page 5 OF 5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Noble House 305420 Installation guide

Brand
Noble House
Model
305420
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents