Spring Roller Shade
Installation Guide
Tools Required
Installation Positions
Outside mount
Protec�ve tape
Power drill and 3/32" drill bit, screwdriver or bits with
phillips heads, level, metal tape measure,
a pencil and note pad
For more informa�on contact [email protected]
Inside mount
L-Brackets for
*For shades 47" and smaller only 2 brackets sets are supplied
( For wider shades an extra third middle bracket is supplied)
Click-on brackets
alterna�ve moun�ng
Spring Roller Shade
Installation Guide - Measurement instruc�ons
Outside mount
For more informa�on contact suppo[email protected]
Inside mount
A
B
(max 73")
A
B
(max 73")
Measure the opening width at top (A):
Inside mount
Measure the window opening width at
t
he top rounded down to the closest 0.5".
The depth of the window frame must be
at least 1.5" for inside mount.
Outside mount
Measure window molding width to the
c
losest 0.5".
If preferred the shade can also be installed
on the wall above the molding.
The maximum height of the iFit shade is 73".
Measure the width from edge to edge of
w
indow molding (A):
Spring Roller Shade
Outside mount
For more informa�on contact suppo[email protected]
Inside mount
Installation Guide - Installa�on posi�ons
Inside mount
Outside mount
Inside mount
using L-bracket
Spring Roller Shade
Installation Guide - Inside mount
For more informaon contact suppo[email protected]
With a pencil, mark the posion of the brackets
approx. 4" from the inside edges. Use the level
to assure that brackets are level across.
For shades 47" and shorter 2 mounng brackets
are supplied.
(For 47,5" and wider shades an extra third middle
bracket is supplied)
Drill mounng holes using a 3/32" drill bit.
Aach brackets with the provided screws using a
screw driver or power drill.
(If installed in drywall use the supplied plugs).
Install the shade by simply clicking it on the
bracket with an up and in moon.
Now the shade can be adjusted sideways by
hand to be centered.
Spring Roller Shade
Installation Guide - Inside mount
For more informa�on contact suppo[email protected]
Carefully remove the protec�ve tape
from the shade.
Spring Roller Shade
Installation Guide - Outside mount
For more informa�on contact suppo[email protected]
With a pencil, check and mark the position of
the brackets, including fixing positions.
Mark posi�on of the brackets approx. 4" from
the edges of the roller shade. Use a spirit level
to ensure the brackets are placed in a straight line.
For shades smaller than 47" only 2 brackets are
supplied (For wider blinds an extra middle bracket
is supplied)
Pre-drill holes for screws. Using a
Phillips head screwdriver, fix the
brackets using the screws provided.
For installation on plaster walls use
the wall plugs provided. In order to
install on aluminium frames pre-drill
holes of 3/32" diameter for
bracket screws.
Now the shade can be adjusted sideways by
hand to be centered.
Spring Roller Shade
Installation Guide - Outside mount
For more informa�on contact suppo[email protected]
Carefully remove the protec�ve tape
from the shade.
Spring Roller Shade
For more informaon contact suppo[email protected]
Installation Guide - Adjusng the Shade (oponal)
1
:
The stop posion can be adjusted to your individual preference.
Option 1: The roller shade is stopping too low
with the in the clockwise direction and insert it back in the bracket slot. Half turns (180°) and full turns
(360°) are possible. The bigger adjustment in the clockwise direction, the higher the shade will stop. More than 1
adjustment might be needed before reaching desired position.
Hold the left part of
with the in the counterclockwise direcon and insert it back in the bracket slot. Half turns (180°) and full
turns (360°
More than 1 adjustment might be needed before reaching desired position.
To adjust the shade, rst remove the plasc cover from the
le bracket, then follow the steps shown below.
the shade with one hand and li the adjustable ring in the bracket. Turn the ring together
the shade with one hand and li the adjustable ring in the bracket. Turn the ring togetherHold the left part of
shade
shade
Option 2: The roller shade is stopping too high
) are possible. The bigger adjustment in the counterclockwise direcon, the lower the shade will stop.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Unbranded MC-102 User manual
-
Perfect Lift Window Treatment HDQGAL640720 User guide
-
Elegant Home Fashions RSND2764W User manual
-
Project Source DFWDD3072-25 Installation guide
-
Demori 14304 Installation guide
-
HOME SO 8541791245 User guide
-
Mairo 32031M User manual
-
Hikvision DS-KV8413-WME1(C)/Flush Quick start guide
-
Unbranded CCDDX6664-62.25 Installation guide
-
HOME basics CDHD_LB5572-51 Operating instructions
