Livex Lighting 40076-05 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
40076-05
Type
Operating instructions

This manual is also suitable for

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
40076
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old fixture and all
hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.
Take care not to lose any small parts necessary for installation.
3. Raise the end of pipe thread into coupling, lock it with the hex nut until tight.
Raise the other end of pipe thread into single bar, place lock washer over
the end of thread protruding through single bar and lock it securely with the
hex nut.
4. Slide the electrical wires through the tube(K)/(J)/(I)/(G)/ring(H)/canopy(F)
and assembled single bar.
5. Raise the tube(K) to the center pipe thread of the lamp body(L), raise the
tube(J)/(I)/(G) and assembled single bar to the screw pipe nipple in order,
then by turning it clockwise until tight.
6. While holding the assembled single bar of fixture body to the ceiling junction
box with junction box screws (E) as shown, tighten screws securely with
screwdriver. The side of the single bar marked "GND" must face out. The
junction box is not included.
7. Connect the electrical wires as Shown in Fig.2, making sure that all wire
nuts are secured. You may have to wrap the connections with electrical
tape. If your outlet has a ground wire (green or bare copper), connect the
fixture ground wire to it. Otherwise connect fixture’s ground wire directly to
the single bar with the green screw provided. After wires are connected,
tuck them carefully inside the Junction Box.
8. Slide the canopy(F) onto the Junction box, lock it securely with the ring(H)
until tight.
9. Install the light bulbs(Not included) in accordance with the fixture
specifications. NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
10.
Raise the end screw of the garnish cluster(A)/(B)/(C) and(D) insert to
the screw hole of lamp body(L), by turn it clockwise until tight. Note:
the garnish cluster(D1+C2),(B3+A3),(C3+D3),(A4+B5),
(D3+C3),(B3+A3) and(C1+D2) must evenly spaced distribution on
the every lap.
Your installation is now complete. Return power to the
j
unction box and test the fixture.
A1PC
C2PCS
B3PCS
D1PC
C3PCS
A4PCS
D3PCS
D2PCS
C1PC
A3PCS
B3PCS
A3PCS
C3PCS
A1PC
C1PC
D2PCS
A3PCS
B3PCS
C3PCS
D3PCS
A4PCS
C3PCS
A3PCS
B3PCS
D1PC
C2PCS
L
AssembledEffect
WHITE
HOUSE
Black
WIRES
(Hot)
FIXTURE
WIRES
BLACK
WIRES
FIXTURE
Bare
FIXTURE
WIRES
(Ground)
HOUSE
(Neutral)
WIRES
White
Green or
WIRES
HOUSE
Copper(Ground)
GREEN
Thread
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20180140076
FIG.1
FIG.2
  • Page 1 1

Livex Lighting 40076-05 Operating instructions

Livex Lighting
Brand
Livex Lighting
Model
40076-05
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents