Toro CCR 3650 GTS Snowthrower User manual

Brand: Toro

Model: CCR 3650 GTS Snowthrower

Category: Snow throwers

Type: User manual

Toro CCR 3650 GTS Snowthrower is a powerful machine designed to clear snow quickly and efficiently. With its 36-inch clearing width and 21-inch intake height, it can handle even the heaviest snowfalls. The snowthrower is powered by a 357cc Toro Premium 4-cycle OHV engine that provides plenty of power to clear snow up to 20 inches deep. It features a 6-speed transmission, including 2 reverse speeds, for easy maneuvering in tight spaces. The snowthrower also has a heated handle to keep your hands warm and comfortable while you work.

Form No. 3355-426 Rev A

CCR™ 3650 GTS® Snowthrower

Model No. 38517 —Serial No. 270000001 and Up

Operator's Manual

Introduction

R ead this infor mation carefully to lear n ho w to operate and

maintain y our product properly and to a v oid injur y and

product damag e . Y ou are responsible for operating the

product properly and safely .

Y ou ma y contact T oro directly at www .T oro .com for

product and accessor y infor mation, help ﬁnding a dealer ,

or to register y our product.

W henev er y ou need ser vice , g en uine T oro par ts , or

additional infor mation, contact an A uthorized Ser vice

Dealer or T oro Customer Ser vice and ha v e the model and

serial n umbers of y our product ready . Figure 1 identiﬁes the

location of the model and serial n umbers on the product.

W rite the n umbers in the space pro vided.

Figure 1

1. Model and serial number location

Model No.

Serial No.

T his man ual identiﬁes potential hazards and has safety

messag es identiﬁed b y the safety aler t symbol ( Figure 2 ),

whic h signals a hazard that ma y cause serious injur y or

death if y ou do not follo w the recommended precautions .

Figure 2

1. Safety alert symbol

T his man ual uses 2 other w ords to highlight infor mation.

Impor tant calls attention to special mec hanical infor mation

and Note emphasizes g eneral infor mation w or th y of special

attention.

Warning

CALIFORNIA

Pr oposition 65 W ar ning

T he engine exhaust fr om this pr oduct contains

chemicals kno wn to the State of Calif or nia to cause

cancer , bir th defects, or other r epr oducti v e har m.

T his spark ignition system complies with Canadian

ICES-002

T he enclosed Engine Owner’ s Man ual is supplied

f or inf or mation r egarding the US En vir onmental

Pr otection Agency (EP A) and the Calif or nia Emission

Contr ol R egulation of emission systems, maintenance,

and w ar ranty . R eplacements may be order ed thr ough

the engine man uf actur er .

Safety

T his sno wthr o w er meets or ex ceeds the B71.3

speciﬁcations of the American National Standards

Institute in ef fect at the time of pr oduction.

R ead and under stand the contents of this man ual

bef or e the engine is ev er star ted.

T his is the safety aler t symbol. It is used to aler t y ou

to potential per sonal injur y hazards. Obey all safety

messa ges that f ollo w this symbol to a v oid possible

injur y or death.

Impr oper l y using or maintaining this sno wthr o w er

could r esult in injur y or death. T o r educe this potential,

compl y with the f ollo wing safety instr uctions.

T his sno w thro w er is capable of amputating hands and

feet and thro wing objects . F ailure to obser v e the follo wing

safety instr uctions could result in serious injur y .

Training

• R ead, understand and follo w all instr uctions on the

mac hine and in the man ual(s) before operating this unit.

Be thoroughly familiar with the controls and the proper

use of the equipment. Kno w ho w to stop the unit and

diseng ag e the controls quic kly .

• Nev er allo w c hildren to operate the equipment. Nev er

allo w adults to operate the equipment without proper

instr uction.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA

• K ee p the area of operation clear of all persons ,

par ticularly small c hildren.

• Ex ercise caution to a v oid slipping or falling, especially

when operating the sno w thro w er in rev erse .

Preparation

• T horoughly inspect the area where the equipment is to

be used and remo v e all door mats , sleds , boards , wires ,

and other foreign objects .

• Do not operate the equipment without w earing

adequate winter g ar ments . A v oid loose ﬁtting clothing

that can g et caught in mo ving par ts . W ear footw ear that

will impro v e footing on slipper y surfaces .

• Handle fuel with care; it is highly ﬂammable .

– Use an appro v ed fuel container .

– Nev er add fuel to a r unning engine or hot engine .

– Fill fuel tank outdoors with extreme care . Nev er ﬁll

fuel tank indoors .

– Nev er ﬁll containers inside a v ehicle or on a tr uc k

or trailer bed with a plastic liner . Alw a ys place

containers on the g round, a w a y from y our v ehicle ,

before ﬁlling .

– W hen practical, remo v e g as-po w ered equipment

from the tr uc k or trailer and refuel it on the g round.

If this is not possible , then refuel suc h equipment

on a trailer with a por table container , rather than

from a g asoline dispenser nozzle .

– K ee p the nozzle in contact with the rim of the fuel

tank or container opening at all times , until refueling

is complete . Do not use a nozzle loc k-open device .

– R e place g asoline cap securely and wipe up spilled

fuel.

– If fuel is spilled on clothing, c hang e clothing

immediately .

• Use extension cords and rece ptacles as speciﬁed b y the

man ufacturer for all units with electric star ting motors .

• Nev er attempt to mak e any adjustments while the engine

is r unning (ex ce pt when speciﬁcally recommended b y

man ufacturer).

• Alw a ys w ear safety glasses or eye shields during

operation or while perfor ming an adjustment or re pair

to protect eyes from foreign objects that ma y be thro wn

from the mac hine .

Operation

• Do not put hands or feet near or under rotating par ts .

K ee p clear of the disc harg e opening at all times .

• Ex ercise extreme caution when operating on or crossing

g ra v el dri v es , w alks , or roads . Sta y aler t for hidden

hazards or trafﬁc .

• After striking a foreign object, stop the engine , remo v e

the ignition k ey , thoroughly inspect the sno w thro w er

for any damag e , and re pair the damag e before restar ting

and operating the sno w thro w er .

• If the unit should star t to vibrate abnor mally , stop the

engine and c hec k immediately for the cause . Vibration

is g enerally a w ar ning of trouble .

• Stop the engine whenev er y ou lea v e the operating

position, before unclog ging the rotor blades or

disc harg e c hute , and when making any re pairs ,

adjustments or inspections .

• W hen cleaning, re pairing or inspecting the sno w

thro w er , stop the engine and mak e cer tain the rotor

blades and all mo ving par ts ha v e stopped. Disconnect

the spark plug wire and k ee p the wire a w a y from the

plug to prev ent someone from accidentally star ting the

engine .

• Do not r un the engine indoors , ex ce pt when star ting

the engine and for transpor ting the sno w thro w er in or

out of the building . Open the outside doors; exhaust

fumes are dang erous .

• Ex ercise extreme caution when operating on slopes .

• Nev er operate the sno w thro w er without proper guards ,

and other safety protecti v e devices in place and w orking .

• Nev er direct the disc harg e to w ard people or areas where

proper ty damag e can occur . K ee p c hildren and others

a w a y .

• Do not o v erload the mac hine capacity b y attempting to

clear sno w at too fast a rate .

• Nev er operate the mac hine at high transpor t speeds

on slipper y surfaces . Look behind and use care when

operating in rev erse .

• Diseng ag e po w er to the rotor blades when sno w

thro w er is transpor ted or not in use .

• Nev er operate the sno w thro w er without g ood visibility

or light. Alw a ys be sure of y our footing, and k ee p a ﬁr m

hold on the handles . W alk; nev er r un.

• Nev er touc h a hot engine or m ufﬂer .

Clearing a Clogged Discharge

Chute

Hand contact with the rotating rotor blades inside the

disc harg e c hute is the most common cause of injur y

associated with sno w thro w ers . Nev er use y our hand to

clean out the disc harg e c hute . T o clear the c hute:

• Shut the engine of f !

• W ait 10 seconds to be sure the rotor blades ha v e

stopped rotating .

• Alw a ys use a clean-out tool, not y our hands .

Maintenance and Storage

• Chec k all fasteners at frequent inter v als for proper

tightness to be sure the equipment is in safe w orking

condition.

• Nev er store the mac hine with fuel in the fuel tank inside

a building where ignition sources are present suc h as hot

w ater heaters , space heaters , or clothes dr yers . Allo w

the engine to cool before storing in any enclosure .

• Alw a ys refer to the Operator’ s Manual for impor tant

details if the sno w thro w er is to be stored for an

extended period.

• Maintain or re place safety and instr uction labels , as

necessar y .

• R un the mac hine a few min utes after thro wing sno w to

prev ent freeze-up of the rotor blades .

Toro Snowthrower Safety

T he follo wing list contains safety infor mation speciﬁc to

T oro products or other safety infor mation that y ou m ust

kno w .

• R otating r otor blades can injur e ﬁnger s or hands.

Sta y behind the handles and a w a y from the disc harg e

opening while operating the sno wthro w er . K eep y our

f ace, hands, feet, and an y other par t of y our body or

clothing a w ay fr om mo ving or r otating par ts.

• Before adjusting, cleaning, re pairing, and inspecting

the sno wthro w er , and before unclog ging the disc harg e

c hute , stop the engine, r emo v e the k ey , and w ait f or

all mo ving par ts to stop .

• Bef or e lea ving the operating position, stop the engine ,

remo v e the k ey , and w ait for all mo ving par ts to stop .

• If a shield, safety device , or decal is damag ed, illegible ,

or lost, re pair or re place it before beginning operation.

Also , tighten any loose fasteners .

• Do not smok e while handling g asoline .

• Do not use the sno wthro w er on a roof .

• Do not touc h the engine while it is r unning or soon

after it has stopped because the engine ma y be hot

enough to cause a bur n.

• P erfor m only those maintenance instr uctions described

in this man ual. Before perfor ming any maintenance ,

ser vice , or adjustment, stop the engine , remo v e the

k ey , and disconnect the wire from the spark plug . If

major re pairs are ev er needed, contact y our A uthorized

Ser vice Dealer .

• Do not c hang e the g o v er nor settings on the engine .

• W hen storing the sno wthro w er for more than 30 da ys ,

drain the fuel from the fuel tank to prev ent a potential

hazard. Store fuel in an appro v ed fuel container .

R emo v e the k ey from the ignition switc h before storing

the sno wthro w er .

• Purc hase only g en uine T oro re placement par ts and

accessories .

Safety and Instructional Decals

Important: Safety and instr uction decals ar e located near ar eas of potential danger . R eplace dama ged decals.

105-1978

Reorder part no. 108-7335

105-1981

Reorder part no. 105-1955

60-9480

104-2767

104-2775

104-4135

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Handle bolt

Curved washer

Knob

Install the handle.

Discharge chute

Phillips head screws

Washers

Locknuts

Install the discharge chute.

Chute crank and mounting plate

Bolts

Locknuts

Install the chute crank.

1. Installing the Handle

1. Cut the plastic tie that secures the control cable to the

handle .

Note: Hold the cable taut to ensure that it sta ys

connected at the bottom.

2. P osition the upper handle as sho wn ( Figure 3 ).

Figure 3

3. Loosely install the handle bolts , cur v ed w ashers , and

knobs ( Figure 4 ).

Figure 4

4. Hook the end of the control cable spring into the

bottom hole of the control bar ( Figure 5 ).

Figure 5

5. Fully inser t the handle bolts ( Figure 6 ).

Important: Ensur e that y ou do not pinch the

contr ol ca ble ( Figur e 6 ).

Figure 6

6. Tighten the knobs until they are sn ug .

7. Adjust the control cable . R efer to Adjusting the Control

Cable .

2. Installing the Discharge

Chute

Install the disc harg e c hute as sho wn ( Figure 7 ).

Figure 7

3. Installing the Chute Crank

1. Inser t the end of the c hute crank through the hole in

the shroud and align the mounting brac k et with the

holes in the lo w er handle ( Figure 8 ).

Figure 8

1. Chute crank 3. Mounting bracket

2. Hole in the shroud 4. Plastic bushing

2. Slo wly rotate the crank until the end of the c hute crank

ﬁts into the hidden g ear opening and the disc harg e

c hute tur ns the crank.

Note: Ensure that the plastic bushing is fully inser ted

into the hole in the mounting brac k et ( Figure 8 ).

3. Secure the mounting brac k et to the handle with 2 bolts

and 2 loc kn uts .

Product Overview

Figure 9

1. Discharge chute 6. Knob

2. Chute crank

7. Handle bolt (2)

3. Control bar 8. Rotor blades

4. Handle 9. Fuel tank cap

5. Control panel

Figure 10

1. Key switch 3. Recoil start

2. Primer

4. Choke lever

Operation

Note: Deter mine the left and right sides of the mac hine

from the nor mal operating position.

Gasoline is extr emel y ﬂamma ble and explosi v e. A

ﬁr e or explosion fr om gasoline can bur n y ou and

other s.

• T o pr ev ent a static charge fr om igniting the

gasoline, place the container and/or sno wthr o w er

on the g r ound bef or e ﬁlling , not in a v ehicle or

on an object.

• Fill the tank outdoor s when the engine is cold.

W ipe up spills.

• Do not handle gasoline when smoking or ar ound

an open ﬂame or spar ks.

• Stor e gasoline in an appr o v ed fuel container , out

of the r each of childr en.

Mixing the Gasoline and Oil

T his sno wthro w er uses a 50:1 g asoline-to-oil mixture . Use

T or o 50:1 2-Cy cle Oil (Fuel Sta biliz er Added) or an

equi v alent high-g rade , NMMA TCW -cer tiﬁed tw o-cycle oil.

Important: T o pr ev ent engine dama ge, do not use

automoti v e oil (such as SAE 30 or 10W30) or fuel mix ed

at the wr ong gasoline-to-oil ratio.

1. P our a half US g allon (1.9 liters) of fresh, unleaded

g asoline into an appro v ed fuel container .

2. Add tw o-cycle oil to the g asoline according to the c har t

belo w ( Figure 11 ):

Figure 11

50:1 Gasoline-to-Oil Ratio Mixing Chart

Gasoline Oil

1 US gallon (3.8 liters) 2.6 ounces (80 ml)

2 US gallons (7.6 liters) 5.2 ounces (160 ml)

3. Install the cap on the fuel container .

4. Shak e the container to mix the g asoline and oil

thoroughly .

5. Slo wly remo v e the cap and add the remaining amount

of g asoline .

Note: Do not mix g asoline and oil in the fuel tank. Oil

at room temperature mix es easier and more thoroughly

than cold oil. Oil belo w 32°F (0°C) requires additional

mixing

Filling the Fuel Tank

Fill the fuel tank with a fresh mixture of g asoline and oil

mix ed at the proper ratio ( Figure 12 ).

Figure 12

Starting the Engine

1. T ur n the ignition k ey cloc kwise to the On position

( Figure 13 ).

Figure 13

2. Mo v e the c hok e lev er to the right ( Figure 14 ).

Figure 14

3. Fir mly push in the primer 2 times with y our thumb ,

holding the primer in for a second before releasing it

eac h time ( Figure 15 ).

Figure 15

4. Pull the recoil star ter ( Figure 16 ).

Figure 16

5. With the engine r unning, mo v e the c hok e lev er to the

left slo wly .

Stopping the Engine

T o stop the engine , tur n the ignition k ey countercloc kwise

to the Off position ( Figure 17 ).

Figure 17

Starting the Rotor Blades

T o star t the rotor blades , hold the control bar ag ainst the

handle ( Figure 18 ).

Figure 18

Stopping the Rotor Blades

T o stop the rotor blades , release the control bar ( Figure 19 ).

Figure 19

Adjusting the Discharge Chute

T o adjust the disc harg e c hute , rotate the c hute crank and

mo v e the c hute deﬂector handle as sho wn ( Figure 20 ).

Figure 20

1. Chute handle 2. Chute deector handle

Preventing Freeze-up after Use

• Let the engine r un for a few min utes to prev ent mo ving

par ts from freezing . Stop the engine , w ait for all

mo ving par ts to stop , and remo v e ice and sno w from

the sno wthro w er .

• With the engine off , pull the recoil star ter handle

sev eral times and push the electric star t button once

(if applicable) to prev ent the recoil and electric star ters

from freezing up .

Operating Tips

T he r otor blades can thr o w stones, toys, and other

f or eign objects and cause serious per sonal injur y to

the operator or to bystander s.

• K eep the ar ea to be clear ed fr ee of all objects that

the r otor blades could pick up and thr o w .

• K eep all childr en and pets a w ay fr om the ar ea

of operation.

• R emo v e the sno w as soon as possible after it falls .

• T o self-propel, raise the handle and tilt the sno wthro w er

slightly forw ard, lifting the wheels off the g round.

T he more y ou tilt the handle forw ard, the faster the

sno wthro w er self-propels .

• If the sno wthro w er does not propel itself forw ard on

slipper y surfaces or in hea vy sno w , push forw ard on

the handle , but allo w the sno wthro w er to w ork at its

o wn pace .

• Ov erlap eac h sw ath to ensure complete sno w remo v al.

• Disc harg e the sno w do wnwind whenev er possible .

• In sno wy and cold conditions , some controls and

mo ving par ts ma y freeze . Do not use ex cessi v e force

when tr ying to operate frozen controls . If y ou ha v e

difﬁculty operating any control or par t, star t the engine

and let it r un for a few min utes .

Maintenance

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the rst operating

hour

• Check the control cable both initially and after the rst hour of operation; adjust it

if necessary.

• Check for loose fasteners and tighten them if necessary.

Yearly

• Check the control cable and adjust it if necessary.

• Check for loose fasteners and tighten them if necessary.

• Have an Authorized Service Dealer inspect the spark plug and replace it if

necessary.

• Inspect the rotor blades and have an Authorized Service Dealer replace the rotor

blades and scraper if necessary.

• Have an Authorized Service Dealer inspect the drive belt and replace it if necessary.

Yearly or before storage

• Prepare the snowthrower for storage.

Adjusting the Control Cable

Checking the Cable

Important: Check the contr ol ca ble f or pr oper

adjustment initiall y , after the ﬁr st operating hour , and

then ann uall y ther eafter .

1. Mo v e the control bar bac k to w ard the handle to remo v e

the slac k in the cable .

2. Ensure that a 1/16 to 1/8 inc h (2 to 3 mm) g ap exists

betw een the control bar and the handle ( Figure 21 ).

Figure 21

1. 1/16 to 1/8 inch (2 to 3 mm) gap

Note: T o adjust the cable , refer to Adjusting the Cable

belo w .

Important: T he contr ol ca ble must contain some

slack when y ou disenga ge the contr ol bar f or the

r otor blades to stop pr oper l y .

Adjusting the Cable

1. Unhook the end of the control cable spring from the

control bar ( Figure 22 ).

Figure 22

2. Mo v e the Z-ﬁtting to a higher or lo w er hole in the

adjuster link as needed to obtain the 1/16 to 1/8 inc h

(2 to 3 mm) g ap betw een the control bar and the handle

( Figure 23 ).

Figure 23

1. Z-tting 2. Adjuster link

Note: Mo ving the Z-ﬁtting higher decreases the g ap

betw een the control bar and the handle; mo ving it lo w er

increases the g ap .

3. R e place the spring co v er and hook the end of the

control cable spring into the bottom hole of the control

bar .

4. Chec k the adjustment; refer to Chec king the Cable .

Note: After extended use , the dri v e belt ma y w ear and lose

its proper belt tension. If the dri v e belt slips (contin uously

squeals) under a hea vy load, increase the belt tension b y

inser ting the spring end into the top hole of the control

bar . T he belt ma y slip (squeal) in w et conditions; to dr y out

the dri v e system, star t the rotor and r un it without a load

for 30 seconds .

Inspecting the Rotor Blades

Before eac h season, inspect the rotor blades for w ear . W hen

a rotor blade edg e has w or n do wn to the w ear indicator

hole , ha v e an A uthorized Ser vice Dealer re place the rotor

blades and the scraper ( Figure 24 )

Figure 24

1. Wear indicator hole

Storage

Storing the Snowthrower

• Gasoline fumes ar e highl y ﬂamma ble, explosi v e,

and danger ous if inhaled. If y ou stor e the pr oduct

in an ar ea with an open ﬂame, the gasoline fumes

may ignite and cause an explosion.

• Do not stor e the sno wthr o w er in a house (li ving

ar ea), basement, or an y other ar ea wher e ignition

sources may be pr esent, such as hot w ater and

space heater s, clothes dr y er s, fur naces, and other

lik e appliances.

Important: Do not use the chute handle to lift the

sno wthr o w er . T his can dama ge the chute handle.

1. Add a fuel stabilizer/conditioner to the fuel in the fuel

tank as directed.

Note: If y ou use T oro 50:1 2-Cycle Oil (Fuel

Stabilizer Added) , y ou do not need to add a fuel

stabilizer/conditioner .

2. R un the engine for 5 min utes to distribute the

conditioned fuel through the fuel system.

3. Stop the engine and allo w it to cool.

4. Use a hand pump to pump the fuel from the fuel tank

into an appro v ed fuel container , or r un the engine until

it stops .

5. Star t the engine and r un it until it stops .

6. Chok e or prime the engine , star t it a third time , and r un

the engine until it will not star t.

7. Slo wly pull the recoil star ter until y ou feel resistance due

to compression pressure , then stop .

8. R elease the star ter tension g radually b y allo wing the

rope to g o bac k slo wly to prev ent the engine from

rev ersing due to compression pressure .

9. Dispose of un used fuel properly . R ecycle it according to

local codes , or use it in y our automobile .

Note: Do not store stabilized fuel for more than 90

da ys .

10. Tighten all loose screws , bolts , and loc kn uts . R e pair or

re place any damag ed par ts .

11. Clean the sno wthro w er thoroughly .

12. Co v er the sno wthro w er and store it in a clean, dr y place

out of the reac h of c hildren. Allo w the engine to cool

before storing it in any enclosure .

Folding the Handle

1. Loosen the knobs and pull out the handle bolts .

2. F old the upper handle forw ard ( Figure 25 ).

Figure 25

Snow Commander

and

Power Curve

Single-stage

Snow Products

The Toro 5-Year GTS Starting Guarantee and

The Toro 2-Year Total Coverage Guarantee

A Full Warranty (Limited Warranty for Commercial Use)

Conditions and Products Covered under The Toro Starting Guarantee

The Toro Company and its afliate, Toro Warranty Company, guarantee that your Toro GTS (Guaranteed to Start) engine, when used for residential purposes*,

will start on the rst or second pull for ve (5) years from the date of purchase, if you provide the routine maintenance it requires, or we will x it free of charge.

This warranty covers the cost of parts and labor, but you must pay transportation costs. This warranty applies to all Snow Commander® and Power Curve®

single-stage Toro Snowthrowers. (Not Powerlite® models.)

Conditions and Products Covered under The Toro Total Coverage Guarantee

The Toro Company and its afliate, Toro Warranty Company, promise to repair any Toro Product used for residential purposes* if defective in materials or

workmanship or if it stops functioning due to the failure of a component for a period of two (2) years from the date of purchase.

This warranty covers the cost of parts and labor, but you must pay transportation costs. This warranty applies to all Snow Commander® and Power Curve®

single-stage Toro Snowthrowers. (Not Powerlite® models.)

Limited Warranty for Commercial Use

Gas-powered Toro Snowthrowers used for commercial, institutional, or rental use are warranted for 45 days against defects in materials or workmanship.

Components failing due to normal wear are not covered by this warranty. The Toro Starting Guarantee does not apply when the product is used commercially.

Items and Conditions Not Covered

There is no other express warranty. This express warranty does not cover the following:

• Cost of regular maintenance service or parts, such as lters, fuel, lubricants, oil changes, spark plugs, cable/linkage adjustments, or brake and clutch

adjustments

• Any product or part which has been altered or misused or required replacement or repair due to accidents or lack of proper maintenance

• Repairs necessary due to electrical supply irregularities or failure to properly prepare the snowthrower prior to any period of non-use over three months

• Pickup and delivery charges

• Operational misuse, neglect, or accidents

• Repairs or attempted repairs by anyone other than a Toro Service outlet

• Repairs or adjustments to correct starting difculties due to the following:

– failure to follow proper maintenance procedures

– snowthrower auger/paddles striking an object

– contaminants in the fuel system

– improper fuel or fuel/oil mixture (consult your Operator’s Manual if in doubt)

– failure to drain the fuel system prior to any period of non-use over three months

• Special operational conditions where starting may require more than two pulls:

– rst time starts after extended period of non-use over three months or seasonal storage

– improper starting procedures

If you are having difculty starting your unit, please check the Operator’s Manual to ensure that you are using the correct starting procedures. This can

save an unnecessary visit to a Service Dealer.

Owner Responsibilities

You must maintain your Toro Product by following the maintenance procedures described in the Operator’s Manual . Such routine maintenance, whether

performed by a dealer or by you, is at your expense.

Instructions for Obtaining Warranty Service

If you think that your Toro Product contains a defect in materials or workmanship, or if a normal, able-bodied adult can no longer start your product’s engine

in one or two pulls, follow this procedure:

1. Contact any Toro Authorized or Master Service Dealer to arrange service at their dealership. To locate a dealer convenient to you, refer to the Yellow Pages of

your telephone directory (look under Lawn Mowers ) or access our website at www.Toro.com. You may also call our Toro Customer Care Department toll free

at 866-336-5205 (U.S. customers) or 866-854-9033 (Canadian customers).

2. Bring the product and your proof of purchase (sales receipt) to the Service Dealer.

3. If for any reason you are dissatised with the Service Dealer’s analysis or with the assistance provided, contact us at: Customer Care Department, Consumer

Division, Toro Warranty Company, 8111 Lyndale Avenue South, Bloomington, MN 55420-1196.

General Conditions

All repairs covered by these warranties must be performed by an Authorized or Master Toro Service Dealer using Toro approved replacement parts. Repair by a

Toro Service Dealer is your sole remedy under these warranties.

Neither The Toro Company nor Toro Warranty Company is liable for indirect, incidental, or consequential damages in connection with the

use of the Toro Products covered by these warranties, including any cost or expense of providing substitute equipment or service during

reasonable periods of malfunction or non-use pending completion of repairs under these warranties.

Some states do not allow exclusions of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the

above exclusions and limitations may not apply to you. This warranty gives you specic legal rights, and you may also have other rights

which vary from state to state.

Countries Other than the United States or Canada

Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee

policies for your country, province, or state. If for any reason you are dissatised with your Distributor’s service or have difculty obtaining guarantee information,

contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

* Residential purposes means use of the product on the same lot as your home. Use at more than one location is considered commercial use, and the commercial

use warranty would apply.

374-0059 Rev A