PrimeSource RLDM2244W Installation guide

Brand: PrimeSource

Model: RLDM2244W

Type: Installation guide

This manual is also suitable for

RLDM2244B

The-DeckMATE

MODEL#’S DM2244W & DM2244B

READ ALL INSTRUCTIONS BEFORE INSTALLING “The-DeckMATE”.

NOTE: Failure to read instructions before assembly and use could result in injury or death.

Failure to assemble as per instructions will void warranty.

Instructions for Installation and Use:

FIG. 1 FIG. 1A

CONTENTS: FIGURES 1 & 1A (ABOVE)

1- DeckMate Frame

1- 2 piece telescoping support

1- Tempered glass sheet

2- Rail strap assemblies with sliding brackets

4- Glass securing tabs

3- 1/4” detent pins

5- #8 x ½” phillipshead screws

IMPORTANT!

STEP 1-

Unpack “The-DeckMATE” and contents and make sure

all components are accounted for. We highly recommend

assembling and installing “The -DeckMate” completely

on your rail WITHOUT THE TEMPERED GLASS

SHEET FIRST to familiarize yourself with the

installation process without the hindrance of the heavy

tempered glass sheet.

STEP 3-

FIG. 2

STEP 2-

Attach loop end of rail strap assemblies to “The-

DeckMATE” frame. Pay careful attention that the strap is

fully engaged over the security tooth. SEE FIGURE 2

Assemble the 2 piece telescoping support arm by inserting smaller bottom section with snap button into the

larger top section with adjustment holes. SEE FIGURE 3 (BELOW)

Depress snap button while simultaneously sliding the smaller bottom section into the larger top section until

desired adjustment is reached. Be sure the snap button clicks into place. SEE FIGURE 3A (BELOW)

Attach telescoping arm assembly to frame using 1 detent pin before placing frame assembly onto rail. SEE

FIGURES 3B AND 3C (BELOW)

FIG. 3 FIG. 3A

STEP 4-

FIG. 3B FIG. 3C

Attach “The-DeckMATE” frame to the railing by wrapping the strap assembly under the railing

and coming up and over the railing from the other side. SEE FIGURE 4 (NEXT PAGE)

Then secure with detent pin. SEE FIGURE 4A (NEXT PAGE)

FIG. 4 FIG. 4A

STEP 5-

FIG. 5 FIG. 5A

Attach telescoping support arm to “The-DeckMATE” frame and secure with detent pin. SEE FIGURE 5

(ABOVE)

Solidly engage the telescoping arm to the outside edge of deck or balcony or to the lower crossbar if attaching

to inside of railing. Adjust accordingly to your rail height so that the table is properly supported and is

horizontal to the ground or slightly angled toward the deck or balcony. The telescoping arm is adjustable every

inch and will fit 36” to 42” rail heights. SEE FIGURE 5A (ABOVE)

STEP 6-

FIG. 6 FIG. 6A

The telescoping support arm attaches to the deck or bottom rail crossbar using 1- #8 x ½” phillipshead screw.

SEE FIGURE 6 (ABOVE)

Once telescoping support is in place check the attaching straps to make sure they are tight. SEE FIGURE

6A (ABOVE). **If you are now familiar and comfortable with the proper installation of “The-

DeckMATE” please repeat entire installation with the tempered glass sheet. If you are completely

comfortable with the proper installation, repeat without the tempered glass sheet as needed. **

STEP 7-

FIG. 7 FIG. 7A

Remove “The-DeckMATE” from railing by removing the detent pins and simply lift the frame off the

railing. Place “The-DeckMATE” frame on a table top or solid flat surface. Place tempered glass sheet

onto the frame. SEE FIGURE 7 (ABOVE)

Secure the tempered glass sheet to frame using the four glass securing tabs and 4 remaining

#8 x ½” phillipshead screws. SEE FIGURE 7A (ABOVE)

Once glass is securely attached to “The-DeckMATE” frame it is ready to be installed back onto the rail.

: THE HOMEOWNER AND/OR COMMERCIAL USER OF THIS TABLE ASSUMES 100% OF THE

RISK AND RESPONSIBILITY FOR ITS SAFE AND PROPER USE.

: CHECK WITH YOUR HOME OWNERS ASSOCIATION OR APARTMENT MANAGER

CONCERNING INSTALLATION.

: REMOVE TABLE AND BRING INSIDE DURING HEAVY STORMS.

DeckMate”.

: PLEASE READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS FURNISHED WITH “The-

: MAXIMUM WEIGHT CAPACITY 50 LBS. DO NOT EXCEED WEIGHT CAPACITY AT ANY TIME.

: NEVER ALLOW ANYONE TO SIT, STAND OR CLIMB ON “The-DeckMATE” AT ANY TIME.

: NEVER USE “The-DeckMATE” FOR ANY PURPOSE OTHER THAN INTENDED USE.

CLEANING INSTRUCTIONS: Your DeckMATE is manufactured using powder coated aircraft

grade aluminum for the frame and will not rust. The U brackets and strap attachments are

made of Powder Coated Steel. Use general purpose glass cleaner to clean the glass and

regular soap and water to clean the frame.

PrimeSource RLDM2244W Installation guide

Brand: PrimeSource

Model: RLDM2244W

Type: Installation guide

This manual is also suitable for

RLDM2244B

Download PDF

report

PrimeSource RLDM2244W Installation guide

This manual is also suitable for

PrimeSource RLDM2244W Installation guide

Other documents