2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Toro
  7. Baffle Kit, 60in Rear Discharge Z Master Mowers

Toro Baffle Kit, 60in Rear Discharge Z Master Mowers Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Baffle Kit, 60in Rear Discharge Z Master Mowers Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3438-977RevA
BafeKit
60inRearDischargeZMaster
®
Mowers
ModelNo.144-0379
InstallationInstructions
Important:Thiskitdoesnotcomewiththerecyclerblades.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.DisengagethePTO,movethemotion-control
leverstotheNEUTRAL-LOCKposition,and
engagetheparkingbrake.
2.Shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operatingposition.
3.Raisethefrontofthemachineandsupportit
withjackstands.
WARNING
Raisingthemowerdeckforservice
ormaintenancerelyingsolelyon
mechanicalorhydraulicjackscouldbe
dangerous.Themechanicalorhydraulic
jacksmaynotbeenoughsupportormay
malfunction,allowingtheunittofall,
whichcouldcauseinjury.
Donotrelysolelyonmechanical
orhydraulicjacksforsupport.Use
adequatejackstandsorequivalent
support.
4.Repairallbentordamagedareasofmower
deckandreplaceanymissingparts.
5.Cleanthemachineofanydebrisonthedeckto
easeinstallation.
6.Removetheexistingblades;refertothe
Operator’sManual.
7.Removethe6hex-socketscrews(5/16x3/4
inch)and6angenuts(5/16inch)pluggingthe
exposedmountingholesinthedeck(Figure1).
Note:Retainthesepartsforfutureuse.
g024524
Figure1
1.Retaintheseparts.
8.Removeandretainthe2rearcarriagebolts(3/8
x2-1/4inches)and2angenuts(3/8inch)from
eachsidewithinthecuttingchambersecuring
thesidebumperstothedecksides.
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3438-977*A
2
InstallingtheBafes
Partsneededforthisprocedure:
1
Front,rightbafe
1
Rear,rightbafe
1
Front,centerbafe
1
Rear,centerbafe
1
Front,leftbafe
1
Rear,leftbafe
1
Rightkickerbafe
1
Centerkickerbafe
1
Leftkickerbafe
2
Locknut(3/8inch)
14
Carriagebolt(3/8x7/8inch)
16
Flangenut(3/8inch)
Procedure
Note:Determinetheleftandrightsidesofthe
machinefromthenormaloperatingposition.
2
g024570
Figure2
1.Front,rightbafe
8.Leftkickerbafe
2.Carriagebolt9.Rear,leftbafe
3.Flangenut
10.Locknut
4.Centerkickerbafe11.Rear,centerbafe
5.Front,centerbafe12.Rear,rightbafe
6.Front,leftbafe13.Rightkickerbafe
7.Carriagebolt(5/16x1inch)andangenut(5/16
inch)—72-inchmodelonly
1.Installthefront,outerbafesusing1carriage
bolt(3/8x7/8inch)and1angenut(3/8inch)
perbafe(Figure2).
Note:Tohelpalignthebafes,looselyinsert
thecarriagebolts(3/8x2-1/2inches)andange
nuts(3/8inch)throughthesideofthebafes
andbumper(Figure5).
2.Installthefront,centerbafeusing3carriage
bolts(3/8x7/8inch)and3angenuts(3/8inch)
asshowninFigure2.
3.Installtherear,outerbafesusing1carriage
bolt(3/8x7/8inch)and1angenut(3/8inch)
perbafeFigure2.
Note:Tohelpalignthebafes,looselyinsert
thecarriagebolts(3/8x2-1/2inches)andange
nuts(3/8inch)throughthesideofthebafes
andbumper(Figure5).
Note:Thefront,outerbafesinstallbetween
therearbafetabs.
3
4.Installtherear,centerbafeusing2carriage
bolts(3/8x7/8inch)and2locknuts(3/8inch)
asshowninFigure3.
Note:Thisbafeinstallsbetweenthefront,
outerbafeanges(Figure3).
Note:Wherethefront,outerbafes,therear,
outerbafes,andtherear,centerbafecome
together,install2carriagebolts(3/8x7/8inch)
and2locknuts(3/8inch)asshowninFigure3.
g021731
Figure3
1.Carriagebolt(3/8x7/8
inch)
3.Frontbafeange
2.Rear,centerbafe4.Locknut(3/8inch)
5.Tightenallthehardware.
6.Installthecorrectkickerbafetoeachchamber
using1carriagebolt(3/8x7/8inch)and1ange
nut(3/8inch)asshowninFigure1.
Note:Thehookedendofeachkickerbafe
attachestotheslotinthechamberbafe(Figure
4).
Note:Youmayneedtoloosenthematingbafe
toallowthehookedendofthekickerbafeto
tcorrectly.
g021732
Figure4
1.Slot
2.Hookedend
4
3
SecuringtheBumpersand
RightandLeftBafetothe
MowerDeck
Partsneededforthisprocedure:
4
Carriagebolt(3/8x2-1/2inches)
4
Flangenut(3/8inch)
Procedure
Note:T oinstallthebumperbolts,youmayneedto
loosenthematingbafeandkickerbafe.
1.Insert2carriagebolts(3/8x2-1/2inches)on
eachsidethroughtherightandleftbafeand
bumpers(Figure5).
g024518
Figure5
1.Flangenut(3/8inch)4.Leftbafe
2.Bumper
5.Rightbafe
3.Carriagebolt(3/8x2-1/2
inches)
2.Securethe2carriageboltsusing2angenuts
(3/8inch)oneachside(Figure5).
3.Torquethecarriageboltsandangenutsto12.4
to14.7N∙m(110to130in-lb).
4
ConvertingBacktoRear
Discharge
NoPartsRequired
Procedure
1.DisengagethePTO,movethemotion-control
leverstotheNEUTRAL-LOCKposition,and
engagetheparkingbrake.
2.Shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operatingposition.
3.Removethenish-cutbafesandkickerbafes.
Retainallthehardware.
4.Replacethenish-cutbladeswithstandard
blades.
5.Installthehex-socketscrews(5/16x3/4inch)
andtheangenuts(5/16inch)intheholes
onthetopofthedeckwiththebolthead
underneath.
Note:Youmustplugallopenholesnotcovered
bybeltshieldsortheframetopreventsand
and/orothersmallobjectsfrombeingthrownup
throughthedeck.
5
Notes:
Notes:
/