VONN Lighting VMW17200BL Installation guide

Brand
VONN Lighting
Model
VMW17200BL
Type
Installation guide

VONN Lighting VMW17200BL is an LED light fixture designed for indoor use. It features a sleek and modern design, making it a great choice for both residential and commercial applications. The fixture emits a bright and even light, making it ideal for use in kitchens, living rooms, bedrooms, and offices. It is also dimmable, allowing you to adjust the light output to create the perfect ambiance for any occasion. Additionally, the fixture is ETL listed, meaning it has been tested and certified to meet safety standards.

Here are some of the key features and benefits of the VONN Lighting VMW17200BL:

VONN Lighting VMW17200BL is an LED light fixture designed for indoor use. It features a sleek and modern design, making it a great choice for both residential and commercial applications. The fixture emits a bright and even light, making it ideal for use in kitchens, living rooms, bedrooms, and offices. It is also dimmable, allowing you to adjust the light output to create the perfect ambiance for any occasion. Additionally, the fixture is ETL listed, meaning it has been tested and certified to meet safety standards.

Here are some of the key features and benefits of the VONN Lighting VMW17200BL:

© VONN Lighting,2017
Installation Guide
ON
VONN Lighting
Model:
VMW17200
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
LADDER
DRILL
SCREW DRIVER
Circuit Box
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
VONN recommends to install the fixture on its own independent circuit.
Do not install the fixture on the same circuit with other appliances, or
HVAC systems.
LED INFO & WARNINGS
•
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
•
Place the wall switch in the “OFF” position of the room you are installing
the fixture.
•
Shut “OFF” the electricity at main fuse box.
•
VONN recommends ELV (Electric Low Voltage) type dimmers for this
fixture.
•
•
Do not remove or replace VONN manufactured driver that is provided
with the fixture.
Parts List
A.
B.
C.
D.
E.
A
B
C
D
E
Mounting Bracket
Outlet Screws x 3
Wire Connectors x 3
Ground Screw x 1
Canopy Screws x 2
GND
© VONN Lighting,2017
WALL
GND
Canopy Screw
E
Mounting
Bracket
A
Ground
Screw
D
Outlet
Screw
B
Wire Connector
C
Fixture Diagram
Outlet Box
WALL
GND
Mounting
Bracket
A
Outlet
Screw
B
Step 1. Install Mounting Bracket
Align mounting bracket (A) with outlet box and
secure with outlet screws (B).
© VONN Lighting,2017
© VONN Lighting,2017
Supply Wires:
WALL
GND
Mounting
Bracket
A
Wire Connector
C
Ground
Screw
D
Ground Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire)
from outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral
Wire) from outlet box.
Connect Bare Copper (Ground Wire) from fixture to Green
or Bare Copper (Ground Wire) from outlet box.
Twist wires together clockwise and secure with wire
connector (C).
Installer Tip (1): If ground wire is not available in outlet box,
then secure Bare Copper (Ground Wire) from fixture to
ground screw (D) on mounting bracket (A).
Installer Tip (2): Supply wires can be either tucked into
outlet box or fixture canopy.
White
(Neutral Wire)
Bare Copper
(Ground Wire)
Step 2. Connect Wires
Black
(Line Wire)
© VONN Lighting,2017
WALL
GND
Mounting
Bracket
A
Step 3. Mount Fixture
Attach fixture to mounting bracket (A). Secure
with canopy screws (E). Tighten with Phillips
head screwdriver.
Canopy
Canopy Screw
E
© VONN Lighting,2017
Step 4. Turn Power ON
Turn electricity “ON” at main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the fixture.
ON
ON
Circuit Box
Rotating shades.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VONN Lighting VMW17200BL Installation guide

Brand
VONN Lighting
Model
VMW17200BL
Type
Installation guide

VONN Lighting VMW17200BL is an LED light fixture designed for indoor use. It features a sleek and modern design, making it a great choice for both residential and commercial applications. The fixture emits a bright and even light, making it ideal for use in kitchens, living rooms, bedrooms, and offices. It is also dimmable, allowing you to adjust the light output to create the perfect ambiance for any occasion. Additionally, the fixture is ETL listed, meaning it has been tested and certified to meet safety standards.

Here are some of the key features and benefits of the VONN Lighting VMW17200BL:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents