HydroShot WG629.1

Worx HydroShot WG629.1 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Worx HydroShot WG629.1 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
20V Max Lithium Portable Power Cleaner EN
Nettoyeur haute pression portatif à batterie au Lithium 20V Max
F
Limpiador a presión portátil 20V Max Lithium ES
P10
P15
P20
WG629 WG629.1
WG629.2 WG629.9
20V Max Lithium Portable Power Cleaner
EN
10
PRODUCT SAFETY
WARNING: Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
WARNING: This product can expose you
to chemicals including lead, phthalate
or bisphenol A which are known to the
State of California to cause cancer, birth
defects or other reproductive harm. Wash
your hands after use. For more information go
to www.P65Warnings.ca.gov .
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using this product basic
precautions should always be followed,
including the following:
1. Read all the instructions before using the
product.
2. To reduce the risk of injury, close supervision
is necessary when a product is used near
children.
3. Know how to stop the product and bleed
pressures quickly. Be thoroughly familiar with
the controls.
4. Stay alert – watch what you are doing.
5. Do not operate the product when fatigued or
under the influence of alcohol or drugs.
6. Keep operating area clear of all persons
7. Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
8. Follow the maintenance instructions specified
in the manual.
9. WARNING – Risk of injection or
injury– do not direct discharge stream at
persons.
10. Do not spray electrical apparatus and wiring.
SAVE THESE INSTRUCTIONS
GENERAL SAFETY WARNINGS
FOR BATTERY PACK
1) WARNING: Risk of fire and burns. Do
not disassemble, heat above 100°C
(212°F), or incinerate. Do not expose cells
or batteries to heat or fire. Avoid storage
in direct sunlight.
2) Dispose of used battery promptly. When
disposing of secondary cells or batteries,
keep cells or batteries of different
electrochemical systems separate from
each other.
3) Keep battery out of reach of children and
in original package until ready to use.
4) Never put batteries in mouth. If
swallowed, contact your physician or
local poison control center.
5) CAUTION – The battery used in this
device may present a risk of fire or
chemical burn if mistreated. Replace
battery with WORX only. Use of another
battery may present a risk of fire or
explosion.
6) WARNING: Do not use a visibly
damaged battery pack or appliance
as applicable.
7) WARNING: Do not modify or attempt
to repair the appliance or the battery
pack as applicable.
8) BATTERY MUST BE RECYCLED.
9) Do not short-circuit a cell or battery. Do
not store cells or batteries haphazardly in
a box or drawer where they may short-
circuit each other or be short-circuited by
conductive materials.
10) Do not subject cells or batteries to
mechanical shock.
11) Keep cells and batteries clean and dry.
Wipe the cell or battery terminals with a
clean dry cloth if they become dirty.
12) Do not maintain secondary cells and
batteries on charge when not in use.
13) Retain the original cell and battery
literature for future reference.
14) Do not use any charger other than that
specifically provided for use with the
equipment. Secondary cells and batteries
need to be charged before use. Always
use the correct charger and refer to the
manufacturer’s instructions or equipment
manual for proper charging instructions.
15) When possible, remove the battery from
the equipment when not in use.
16) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to battery pack, picking up
or carrying the appliance. Carrying the
appliance with your finger on the switch
or energizing appliance that have the
switch on invites accidents.
17) Disconnect the battery pack from
the appliance before making any
adjustments, changing accessories, or
storing appliance. Such preventive safety
measures reduce the risk of starting the
appliance accidentally.
18) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
19) Have servicing performed by a qualified
repair person using only identical
replacement parts. This will ensure that
the safety of the product is maintained.
20V Max Lithium Portable Power Cleaner
EN
11
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
Warning
Li-Ion battery, battery must be
recycled
Remove battery from the socket
before carrying out any adjustment,
servicing or maintenance.
POSITEC Inc. has established
a partnership with the RBRC
Corporation to recycle any Positec
batteries with the RBRC-call2recycle
seal. For environmental protection,
please do not discard batteries in
the trash. After the batteries’ life
cycle is ended, then please call
1-800-822-8837 for a free service
that will properly dispose of the
battery.
COMPONENT LIST
1. PRESSURE SETTING SWITCH
2. LOCK-OFF SWITCH
3. BATTERY PACK RELEASE BUTTON
4. BATTERY PACK*
5. ON/OFF SWITCH LEVER
6. HOSE ADAPTER
7. POWER NOZZLE
8. EXTENSION LANCE
9. SHORT LANCE
10. NOZZLE ADAPTER
11. MULTI-SPRAY NOZZLE
12. FIXING NAIL
13. HOSE CONNECTOR
14. HOSE FILTER
15. HOSE CLIP
16. HOSE
17. FLOATER
18. SOAP BOTTLE*
19. BRUSH*
20.
WINDOW SQUEEGEE WITH WATER SPRAYER*
21. CARRY BAG
22. FILTER SCREEN (SEE FIG. G2)
23. TURBO NOZZLE*
24. BOTTLE CAP*
* Not all the accessories illustrated or
described are included in standard delivery.
TECHNICAL DATA
WG629
WG629.1 WG629.2
WG629.9
Charger voltage 120V~60Hz /
Voltage 20 V Max**
Pressure
High/Low (garden hose
connected)
Long wand
working mode
max 320psi / 175psi
Short wand
working mode
max 94psi / 72psi
Max water flow
rate
0.5gpm
Max. inlet water
pressure
73psi (0.5MPa)
Suction height max 5ft.
Weight (with lance) 3.7lbs 2.8lbs
** Voltage measured without workload. Initial battery
voltage reaches maximum of 20 volts. Nominal
voltage is 18 volts.
20V Max Lithium Portable Power Cleaner
EN
12
ACCESSORIES
WG629 WG629.1 WG629.2 WG629.9
Hose 20ft.(6m)
1 1 1 1
Short lance
1 1 1 1
Extension
lance
1 1 1 1
Multi-Spray
nozzle
1 1 1 1
Carry bag
1 1 1 1
Battery pack
(WA3575)
1
1 1
/
Charger
(WA3742)
1 1 1 /
Window
squeegee with
water sprayer
(WA4050)
/ 1 / /
Brush
(WA4048)
/ 1 / /
Soap bottle
(WA4036)
/ 1 / /
Bottle cap
(WA4038)
/ 1 1 /
Only use the appropriate accessories intended for
this tool. Accessory information can be found on
the product packaging, at a WORX dealer or on our
website at www.worx.com.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
ASSEMBLY & OPERATION
ACTION FIGURE
BEFORE OPERATION
Installing the battery pack See Fig. A1
Removing the battery pack See Fig. A2
Charging the battery pack
More details can be found in WA3742’s
manual
See Fig. A3
ASSEMBLY
NOTE: The power nozzle has two
working modes: short lance only
and short lance used together with
extension lance.
Working mode 1
Attaching short lance to the power
nozzle
NOTE: When attaching, align the
two projections on the lance with the
grooves of the power nozzle as shown
in Fig. B.
NOTE: In this working mode, the
highest pressure is 94psi. it is suitable
for light duty cleaning and watering.
See Fig. B
Attaching the Multi-spray nozzle
NOTE: When attaching, rotating the
nozzle left and right to make sure the
nozzle fully seated into position and
gently pulling it to make sure it is
locked into position securely.
See Fig. C
Working mode 2
Attaching extension lance to the power
nozzle
Attaching short lance to the extension
lance
NOTE: When attaching, align the
two projections on the lance with the
grooves of the power nozzle as shown
in Fig. D, E.
NOTE: In this working mode, the
highest pressure is 320psi. it is suitable
for removing strong stains.
See Fig.
D, E
Attaching the hose to the power nozzle
NOTE: After the hose is attached, check
the connection by gently pulling upon
the hose. It should not be pulled off.
See Fig.
F1, F2
Attaching your own water hose
(optional)
1. Remove the hose adapter
2. Attach the home garden hose with
suitable connectors
NOTE: Except for the hose supplied,
you can also connect the power nozzle
to your own water hose with suitable
connectors.
NOTE: Check whether the filter screen
is missing before retightening the hose
adapter. When retightening the quick
hose adapter, please tighten securely.
Otherwise, it may not draw any water
for proper operation.
See Fig.
G1, G2, G3
OPERATION
Pressure setting
Your power nozzle has two pressure
modes.
See Fig. H
20V Max Lithium Portable Power Cleaner
EN
13
Start
NOTE: At the first use, you need to
empty the air in hose, place the
power nozzle below waist level
(<5ft/1.5m), then attach the extension
lance and set it at high pressure. Do not
start working until the water
goes up along the hose and sprays out.
This could take up to 30
seconds or more depending on the
fresh water source.
See Fig. I
Selecting the nozzle pattern
NOTE: Choose a suitable nozzle
pattern according to your work. Spray
patterns 0
o
, 15
o
, 25
o
and 40
o
are
applicable for cleaning, and the spray
pattern with the symbol is best
suitable for watering.
WARNING: Do not shift the nozzle
pattern when the tool is powered on.
See Fig. J
Cleaning (Working mode 2)
WARNING: Do not connect the
machine to water supplies that
are dirty, rusty, muddy, or
corrosive. (Including window
cleaning liquids, plant foods, or
fertilizers etc.)
NOTE: Not recommended for use with
salt water, immediately rinse with fresh
water for proper maintenance.
See Fig.
K, L
Watering (Working mode 1) See Fig. M
ATTACHMENT OF
ACCESSORIES
A number of accessories have been supplied with
this product and are required for use in different
applications. Do not attempt to use cleaning
without a lance or any accessories attached.
1. Soap bottle (WG629.1 only)
Soap bottle provides detergent suds for deeper
cleaning of dirt. It is used in conjunction with power
nozzle or extension lance. (See Fig. N1, N2)
2. Brush (WG629.1 only)
Brush is for cleaning cars, boats, motorcycles
etc. It is used in conjunction with power nozzle or
extension lance. (See Fig. O1, O2)
3. Window squeegee with water sprayer
(WG629.1 only)
The window squeegees quick connection easily
snaps into the tool to spray water or wipe off
water from glass or tiled surfaces. Suitable for the
HydroShot power cleaner or the extension lance.
(See Fig. P1, P2, P3, P4)
4. Bottle cap (WG629.1 WG629.2)
The bottle cap accessory allows the tool to directly
connect with most 2 Liter bottles with approximately
1” openings. (NOTE: May not fit all consumable soda
and water bottles) (See Fig. Q1, Q2, Q3)
WARNING: Do not install the bottle cap
accessory until it is ready to be used. The
accessories vents will leak liquid, if a bottle is
installed, with the machine lying on a surface.
5. Turbo nozzle (WA4037, not included in
WG629 models)
The turbo nozzle delivers 360° of rotating water,
which cleans a larger area than the 0° water
pattern during the same time period. Suitable with
the extension lance installed on the HydroShot.
Recommend to use it with high pressure setting
(See Fig. R)
MAINTENANCE
Remove the Battery Pack from the tool before
carrying out any adjustment, servicing or
maintenance.
Inspect the product for damaged or worn parts
before each use. Do not operate it if you find
damaged or worn parts. Contact your supplier or the
manufacturer for replacement parts.
Hose filter maintenance
Remove the hose filter from the hose and get out
the strainer. Rinse the parts with clean water before
reassembling. (See Fig. S1, S2)
CLEANING/STORAGE
Before Storage, completely drain all the water from
the machine and hose.
Clean the moulded plastic housing of the machine
using a soft brush and clean cloth. Do not use water,
solvents or polishes. Store in a secure and dry place
out of the reach of children. Do not place other
objects on the product.
Store the machine and the accessories in a frost free
place.
1514
20V Max Lithium Portable Power Cleaner
EN
14
TROUBLESHOOTING
Symptom Possible causes Solution
Machine turns on but
it does not draw any
water or there is not
sufficient pressure.
Power nozzle is too high from
the water source surface.
Lower the machine below 5ft/1.5m.
Hose filter is blocked.
Take out the hose filter and rinse the parts with
clean water. (See Fig. S1, S2)
The users garden hose is not
well connected to the machine.
Check and reattach the garden hose tightly. (See
Fig. G3)
Hose adapter looses.
The filter screen is missing.
(See Fig. G2)
Tighten the hose adapter securely with a
spanner.
Contact WORX service agent to get a filter
screen.
Pump, hose, or other parts
are frozen due to outside
temperatures.
Wait for the pump, hose or other parts to thaw.
Hose kinks. Straighten out the hose.
Multi-spray nozzle
leaks.
The nozzle pattern does not
spray correctly.
Make sure the nozzle pattern symbol aligns
with the indicator mark on tool.
Fixing nail of the multi-spray
nozzle loosens.
Tighten it with a hex key.
Outlet pressure
increases suddenly.
Multi-spray nozzle is blocked. Replace with a new multi-spray nozzle.
Machine drains out
water after stopping.
There is water remaining in the
lance and pump after stopping.
Drain all the water completely before storage.
Soap accessory
cannot spray out any
detergent.
Blockage in the soap bottle. Clean it with fresh water.
Machine does not
start.
The battery pack is not attached
well.
Reinstall the battery pack.
Battery pack is empty.
Replace with a new battery pack or recharge the
battery pack.
Defective battery. Replace with a new battery pack.
Machine pressure is
not consistent.
Additional air could be sucked
into the machine.
Check connection between the hose adapter
and the hose.
It is at low pressure setting. No action need.
Machine stops
automatically.
Battery pack is empty.
Replace with a new battery pack or recharge the
battery pack.
The multi-spray nozzle is
blocked. The current protection
is activated.
Remove the multi-spray nozzle and turn on
the machine. If the machine works normally,
replace with a new multi-spray nozzle.
Copyright © 2017, Positec. All Rights Reserved.
Copyright © 2017, Positec. Tous droits réservés.
© Derechos reservados 2017, Positec. Todos los derechos reservados.
AR01276503
www.worx.com
/