Worx HydroShot WG629 Owner's manual

20V Max Lithium Portable Power Cleaner EN

Nettoyeur haute pression portatif à batterie au Lithium 20V Max

F

Limpiador a presión portátil 20V Max Lithium ES

P10

P15

P20

WG629 WG629.1

WG629.2 WG629.9

Page is loading ...

20V Max Lithium Portable Power Cleaner

EN

10

PRODUCT SAFETY

WARNING: Read all safety warnings and

all instructions. Failure to follow the

warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

WARNING: This product can expose you

to chemicals including lead, phthalate

or bisphenol A which are known to the

State of California to cause cancer, birth

defects or other reproductive harm. Wash

your hands after use. For more information go

to www.P65Warnings.ca.gov .

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using this product basic

precautions should always be followed,

including the following:

1. Read all the instructions before using the

product.

2. To reduce the risk of injury, close supervision

is necessary when a product is used near

children.

3. Know how to stop the product and bleed

pressures quickly. Be thoroughly familiar with

the controls.

4. Stay alert – watch what you are doing.

5. Do not operate the product when fatigued or

under the inﬂuence of alcohol or drugs.

6. Keep operating area clear of all persons

7. Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

8. Follow the maintenance instructions speciﬁed

in the manual.

9. WARNING – Risk of injection or

injury– do not direct discharge stream at

persons.

10. Do not spray electrical apparatus and wiring.

SAVE THESE INSTRUCTIONS

GENERAL SAFETY WARNINGS

FOR BATTERY PACK

1) WARNING: Risk of ﬁre and burns. Do

not disassemble, heat above 100°C

(212°F), or incinerate. Do not expose cells

or batteries to heat or ﬁre. Avoid storage

in direct sunlight.

2) Dispose of used battery promptly. When

disposing of secondary cells or batteries,

keep cells or batteries of different

electrochemical systems separate from

each other.

3) Keep battery out of reach of children and

in original package until ready to use.

4) Never put batteries in mouth. If

swallowed, contact your physician or

local poison control center.

5) CAUTION – The battery used in this

device may present a risk of ﬁre or

chemical burn if mistreated. Replace

battery with WORX only. Use of another

battery may present a risk of ﬁre or

explosion.

6) WARNING: Do not use a visibly

damaged battery pack or appliance

as applicable.

7) WARNING: Do not modify or attempt

to repair the appliance or the battery

pack as applicable.

8) BATTERY MUST BE RECYCLED.

9) Do not short-circuit a cell or battery. Do

not store cells or batteries haphazardly in

a box or drawer where they may short-

circuit each other or be short-circuited by

conductive materials.

10) Do not subject cells or batteries to

mechanical shock.

11) Keep cells and batteries clean and dry.

Wipe the cell or battery terminals with a

clean dry cloth if they become dirty.

12) Do not maintain secondary cells and

batteries on charge when not in use.

13) Retain the original cell and battery

literature for future reference.

14) Do not use any charger other than that

speciﬁcally provided for use with the

equipment. Secondary cells and batteries

need to be charged before use. Always

use the correct charger and refer to the

manufacturer’s instructions or equipment

manual for proper charging instructions.

15) When possible, remove the battery from

the equipment when not in use.

16) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to battery pack, picking up

or carrying the appliance. Carrying the

appliance with your ﬁnger on the switch

or energizing appliance that have the

switch on invites accidents.

17) Disconnect the battery pack from

the appliance before making any

adjustments, changing accessories, or

storing appliance. Such preventive safety

measures reduce the risk of starting the

appliance accidentally.

18) Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, ﬂush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

19) Have servicing performed by a qualiﬁed

repair person using only identical

replacement parts. This will ensure that

the safety of the product is maintained.

20V Max Lithium Portable Power Cleaner

EN

11

SYMBOLS

To reduce the risk of injury, user

must read instruction manual

Warning

Li-Ion battery, battery must be

recycled

Remove battery from the socket

before carrying out any adjustment,

servicing or maintenance.

POSITEC Inc. has established

a partnership with the RBRC

Corporation to recycle any Positec

batteries with the RBRC-call2recycle

seal. For environmental protection,

please do not discard batteries in

the trash. After the batteries’ life

cycle is ended, then please call

1-800-822-8837 for a free service

that will properly dispose of the

battery.

COMPONENT LIST

1. PRESSURE SETTING SWITCH

2. LOCK-OFF SWITCH

3. BATTERY PACK RELEASE BUTTON

4. BATTERY PACK*

5. ON/OFF SWITCH LEVER

6. HOSE ADAPTER

7. POWER NOZZLE

8. EXTENSION LANCE

9. SHORT LANCE

10. NOZZLE ADAPTER

11. MULTI-SPRAY NOZZLE

12. FIXING NAIL

13. HOSE CONNECTOR

14. HOSE FILTER

15. HOSE CLIP

16. HOSE

17. FLOATER

18. SOAP BOTTLE*

19. BRUSH*

20.

WINDOW SQUEEGEE WITH WATER SPRAYER*

21. CARRY BAG

22. FILTER SCREEN (SEE FIG. G2)

23. TURBO NOZZLE*

24. BOTTLE CAP*

* Not all the accessories illustrated or

described are included in standard delivery.

TECHNICAL DATA

WG629

WG629.1 WG629.2

WG629.9

Charger voltage 120V~60Hz /

Voltage 20 V Max**

Pressure

High/Low (garden hose

connected)

Long wand

working mode

max 320psi / 175psi

Short wand

working mode

max 94psi / 72psi

Max water ﬂow

rate

0.5gpm

Max. inlet water

pressure

73psi (0.5MPa)

Suction height max 5ft.

Weight (with lance) 3.7lbs 2.8lbs

** Voltage measured without workload. Initial battery

voltage reaches maximum of 20 volts. Nominal

voltage is 18 volts.

20V Max Lithium Portable Power Cleaner

EN

12

ACCESSORIES

WG629 WG629.1 WG629.2 WG629.9

Hose 20ft.(6m)

1 1 1 1

Short lance

1 1 1 1

Extension

lance

1 1 1 1

Multi-Spray

nozzle

1 1 1 1

Carry bag

1 1 1 1

Battery pack

(WA3575)

1

1 1

/

Charger

(WA3742)

1 1 1 /

Window

squeegee with

water sprayer

(WA4050)

/ 1 / /

Brush

(WA4048)

/ 1 / /

Soap bottle

(WA4036)

/ 1 / /

Bottle cap

(WA4038)

/ 1 1 /

Only use the appropriate accessories intended for

this tool. Accessory information can be found on

the product packaging, at a WORX dealer or on our

website at www.worx.com.

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

ASSEMBLY & OPERATION

ACTION FIGURE

BEFORE OPERATION

Installing the battery pack See Fig. A1

Removing the battery pack See Fig. A2

Charging the battery pack

More details can be found in WA3742’s

manual

See Fig. A3

ASSEMBLY

NOTE: The power nozzle has two

working modes: short lance only

and short lance used together with

extension lance.

Working mode 1

Attaching short lance to the power

nozzle

NOTE: When attaching, align the

two projections on the lance with the

grooves of the power nozzle as shown

in Fig. B.

NOTE: In this working mode, the

highest pressure is 94psi. it is suitable

for light duty cleaning and watering.

See Fig. B

Attaching the Multi-spray nozzle

NOTE: When attaching, rotating the

nozzle left and right to make sure the

nozzle fully seated into position and

gently pulling it to make sure it is

locked into position securely.

See Fig. C

Working mode 2

Attaching extension lance to the power

nozzle

Attaching short lance to the extension

lance

NOTE: When attaching, align the

two projections on the lance with the

grooves of the power nozzle as shown

in Fig. D, E.

NOTE: In this working mode, the

highest pressure is 320psi. it is suitable

for removing strong stains.

See Fig.

D, E

Attaching the hose to the power nozzle

NOTE: After the hose is attached, check

the connection by gently pulling upon

the hose. It should not be pulled off.

See Fig.

F1, F2

Attaching your own water hose

(optional)

1. Remove the hose adapter

2. Attach the home garden hose with

suitable connectors

NOTE: Except for the hose supplied,

you can also connect the power nozzle

to your own water hose with suitable

connectors.

NOTE: Check whether the ﬁlter screen

is missing before retightening the hose

adapter. When retightening the quick

hose adapter, please tighten securely.

Otherwise, it may not draw any water

for proper operation.

See Fig.

G1, G2, G3

OPERATION

Pressure setting

Your power nozzle has two pressure

modes.

See Fig. H

20V Max Lithium Portable Power Cleaner

EN

13

Start

NOTE: At the ﬁrst use, you need to

empty the air in hose, place the

power nozzle below waist level

(<5ft/1.5m), then attach the extension

lance and set it at high pressure. Do not

start working until the water

goes up along the hose and sprays out.

This could take up to 30

seconds or more depending on the

fresh water source.

See Fig. I

Selecting the nozzle pattern

NOTE: Choose a suitable nozzle

pattern according to your work. Spray

patterns 0

o

, 15

o

, 25

o

and 40

o

are

applicable for cleaning, and the spray

pattern with the symbol is best

suitable for watering.

WARNING: Do not shift the nozzle

pattern when the tool is powered on.

See Fig. J

Cleaning (Working mode 2)

WARNING: Do not connect the

machine to water supplies that

are dirty, rusty, muddy, or

corrosive. (Including window

cleaning liquids, plant foods, or

fertilizers etc.)

NOTE: Not recommended for use with

salt water, immediately rinse with fresh

water for proper maintenance.

See Fig.

K, L

Watering (Working mode 1) See Fig. M

ATTACHMENT OF

ACCESSORIES

A number of accessories have been supplied with

this product and are required for use in different

applications. Do not attempt to use cleaning

without a lance or any accessories attached.

1. Soap bottle (WG629.1 only)

Soap bottle provides detergent suds for deeper

cleaning of dirt. It is used in conjunction with power

nozzle or extension lance. (See Fig. N1, N2)

2. Brush (WG629.1 only)

Brush is for cleaning cars, boats, motorcycles

etc. It is used in conjunction with power nozzle or

extension lance. (See Fig. O1, O2)

3. Window squeegee with water sprayer

(WG629.1 only)

The window squeegees quick connection easily

snaps into the tool to spray water or wipe off

water from glass or tiled surfaces. Suitable for the

HydroShot power cleaner or the extension lance.

(See Fig. P1, P2, P3, P4)

4. Bottle cap (WG629.1 WG629.2)

The bottle cap accessory allows the tool to directly

connect with most 2 Liter bottles with approximately

1” openings. (NOTE: May not ﬁt all consumable soda

and water bottles) (See Fig. Q1, Q2, Q3)

WARNING: Do not install the bottle cap

accessory until it is ready to be used. The

accessories vents will leak liquid, if a bottle is

installed, with the machine lying on a surface.

5. Turbo nozzle (WA4037, not included in

WG629 models)

The turbo nozzle delivers 360° of rotating water,

which cleans a larger area than the 0° water

pattern during the same time period. Suitable with

the extension lance installed on the HydroShot.

Recommend to use it with high pressure setting

(See Fig. R)

MAINTENANCE

Remove the Battery Pack from the tool before

carrying out any adjustment, servicing or

maintenance.

Inspect the product for damaged or worn parts

before each use. Do not operate it if you ﬁnd

damaged or worn parts. Contact your supplier or the

manufacturer for replacement parts.

Hose ﬁlter maintenance

Remove the hose ﬁlter from the hose and get out

the strainer. Rinse the parts with clean water before

reassembling. (See Fig. S1, S2)

CLEANING/STORAGE

Before Storage, completely drain all the water from

the machine and hose.

Clean the moulded plastic housing of the machine

using a soft brush and clean cloth. Do not use water,

solvents or polishes. Store in a secure and dry place

out of the reach of children. Do not place other

objects on the product.

Store the machine and the accessories in a frost free

place.

1514

20V Max Lithium Portable Power Cleaner

EN

14

TROUBLESHOOTING

Symptom Possible causes Solution

Machine turns on but

it does not draw any

water or there is not

sufﬁcient pressure.

Power nozzle is too high from

the water source surface.

Lower the machine below 5ft/1.5m.

Hose ﬁlter is blocked.

Take out the hose ﬁlter and rinse the parts with

clean water. (See Fig. S1, S2)

The users garden hose is not

well connected to the machine.

Check and reattach the garden hose tightly. (See

Fig. G3)

Hose adapter looses.

The ﬁlter screen is missing.

(See Fig. G2)

Tighten the hose adapter securely with a

spanner.

Contact WORX service agent to get a ﬁlter

screen.

Pump, hose, or other parts

are frozen due to outside

temperatures.

Wait for the pump, hose or other parts to thaw.

Hose kinks. Straighten out the hose.

Multi-spray nozzle

leaks.

The nozzle pattern does not

spray correctly.

Make sure the nozzle pattern symbol aligns

with the indicator mark on tool.

Fixing nail of the multi-spray

nozzle loosens.

Tighten it with a hex key.

Outlet pressure

increases suddenly.

Multi-spray nozzle is blocked. Replace with a new multi-spray nozzle.

Machine drains out

water after stopping.

There is water remaining in the

lance and pump after stopping.

Drain all the water completely before storage.

Soap accessory

cannot spray out any

detergent.

Blockage in the soap bottle. Clean it with fresh water.

Machine does not

start.

The battery pack is not attached

well.

Reinstall the battery pack.

Battery pack is empty.

Replace with a new battery pack or recharge the

battery pack.

Defective battery. Replace with a new battery pack.

Machine pressure is

not consistent.

Additional air could be sucked

into the machine.

Check connection between the hose adapter

and the hose.

It is at low pressure setting. No action need.

Machine stops

automatically.

Battery pack is empty.

Replace with a new battery pack or recharge the

battery pack.

The multi-spray nozzle is

blocked. The current protection

is activated.

Remove the multi-spray nozzle and turn on

the machine. If the machine works normally,

replace with a new multi-spray nozzle.

Page is loading ...

AR01276503

www.worx.com

Worx HydroShot WG629 Owner's manual

Worx HydroShot WG629 Owner's manual

in other languages

Related papers

Other documents