Minka Lavery 5414-281 Installation guide

Type
Installation guide

Minka Lavery 5414-281 is a ceiling fixture designed for indoor use. It features a classic design with a metal frame and a glass shade, making it suitable for various décor styles. The fixture requires an A19 E26 (MED BASE) light bulb, which is not included. Installation requires basic electrical knowledge and tools, including a screwdriver and wire cutters. Once installed, the fixture provides illumination for spaces such as bedrooms, living rooms, and hallways.

Minka Lavery 5414-281 is a ceiling fixture designed for indoor use. It features a classic design with a metal frame and a glass shade, making it suitable for various décor styles. The fixture requires an A19 E26 (MED BASE) light bulb, which is not included. Installation requires basic electrical knowledge and tools, including a screwdriver and wire cutters. Once installed, the fixture provides illumination for spaces such as bedrooms, living rooms, and hallways.

INSTALLATION INSTRUCTIONS
Item#5414-281 (New. 01/15/2015)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE FIXTURE (Fig.1)
1.
Shut off the power at the circuit breaker and remove
the old fixture, including the mounting hardware.
2.
Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Position mounting plate (A) on the
wall, and mark
the location of two dry wall anchors (J). Pre-d
rill the
holes for the dry wall anchors. Insert the
dry wall
anchors (J) into the wall.
4. Attach the mounting plate (A) to the junction b
ox
using the Mounting screws (B)
. The side of the
mounting plate marked “GND” must face out.
5. Place the mounting screw (K) through
the keyhole
into the dry wall anchor (J) to secure the Mounting
plate (A) as shown in Fig.1.
CONNECTING THE WIRES (Fig. 2)
6. At this point, c
onnect the electrical wires as shown
in Fig. 2, making sure that all wire connectors are
secured. If your outlet box
or bare copper), connect the fixture’s ground w
ire to
it. Otherwise, connect the fixture’s ground w
ire
directly to the mounting plate using the green s
crew
provided. After the wires are connected,
tuck them
carefully inside the junction box.
FINISHING THE INSTALLATION (Fig.1)
7. Place fixture body (D) over mounting plate (A) and
fasten with Screws (C).
8.
Place the glass shade (F) followed by metal ring (G)
over the socket. Use tool (I) and screw shell (H) to
secure the glass into the fixture body.
9. Install the A19 E26
(MED BASE) light bulb (not
included) in accordance with the fixture’s
specifications.
(DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (
NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Retur
n power and
test the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2444E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOU
SE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
F
G
H
I
A
B
C
J
K
D
Socket ring # SKT-RING-26
E26 Socket Spanner: WRH-1-51
Set
#
A
-
02
1
-
220119B
-Mounting Plate
-Ground screw
-Mounting Screw*2
  • Page 1 1

Minka Lavery 5414-281 Installation guide

Type
Installation guide

Minka Lavery 5414-281 is a ceiling fixture designed for indoor use. It features a classic design with a metal frame and a glass shade, making it suitable for various décor styles. The fixture requires an A19 E26 (MED BASE) light bulb, which is not included. Installation requires basic electrical knowledge and tools, including a screwdriver and wire cutters. Once installed, the fixture provides illumination for spaces such as bedrooms, living rooms, and hallways.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI