Install Manual
Wall Mounting Bracket
Please read this manual carefully before operating your set
and retain it for future reference.
OSW100
www.lg.com
(Brazil: www.lge.com/br)
P/NO : MFL63640561 (1407-REV00)
2
COMPONENT
Install manual Wall mount anchor 4 units Wall mount screw 4 units
* Component of top wall mount
Top wall mount 2 spacers (front) 2 spacers (back) 1 pin for fixing top wall
mount
Hanger 2 screws for attaching the hanger
(M6 x L33 mm)
* Component of bottom wall mount
1 bottom-right wall
mount
1 bottom-left wall mount 2 bottom wall attaching
brackets
8 washers
Contents
COMPONENT 2
IMPORTANT SAFETY INSTRUCTIONS 3
How to Attach the Spacers to the Hanger 4
BEFORE INSTALLATION 4
INSTALLATION METHOD 4
How to Attach the Brackets for the Product to the TV 5
How to attach to masonry walls 6
How to Install the Top Wall Mount 7
How to Install the Bottom Wall Mount 8
How to Attach the Top Wall Mount to the Product 9
How to Install the Top Wall Mount Fixing Pin 9
How to Adjust the Level of the Product 10
How to Tidy Up Cables 10
PRODUCT SPECIFICATION 11
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions.
Heed all warnings. Follow all instructions.
Warning
This wall mount should be installed by a
trained and experienced installer designated
by the retailer.
Having the product installed by a non-specialized
installer is very dangerous and can cause damage
or injury.
Do not install the product where the weight
cannot be supported.
If the strength of the location where the wall mount
is installed is not strong enough, it can fall off and
cause an injury.
Use a trained and experienced installer to
move or replace the wall mount, if needed.
Installation requires special techniques. Moving or
installing the product on your own can cause
serious safety issues.
After installing the wall mount, do not hang on
the product or apply severe impact to the
product.
The product can fall off and cause injury.
When installing the wall mount, never hang the
power or signal cable on the rear side the TV.
The cord can be damaged and cause a fire, an
electric shock, or damage to the product.
Caution
Install the product according to the directions
in the user manual.
If the product is not installed based on the
directions in the user manual, it can cause a
serious injury or damage to the product.
When installing the product or adjusting the
height of the product after installing, always do
so with 2 people.
Working alone can cause the product to fall off and
result in injury or damage to the product.
During the installation, check the type of wall
material and use the sealed anchor and screw
if the conditions comply.
If you do not use the designated anchor or screw,
the mount may not be able to withstand the
weight of the product and cause a safety issue.
When drilling holes in the wall, always use a drill
bit and drill of designated diameter. Also follow the
designated directions for the depth of the hole.
If the product is installed without following the
designated method, the product may be unstable
and cause a safety issue.
Do not wipe the product with a wet towel and
do not use any heater or humidifier below
where the product is installed.
If water flows into the product or if moisture and
heat are applied to the product, it can cause a fire,
an electric shock, or problem to the product.
Do not install the product near any object that
may cause vibration.
Do not install the product near any high
voltage power cable or power source.
Unplug the power cord from the power outlet
before installing the product.
If you install the product with the power cord
plugged, it can cause an electric shock or a fire.
Do not install the product with bare hands.
Always wear proper work gloves.
It can cause an injury.
Do not allow the video connectors connected
to the display to press against the wall. Use
the included right-angle adapters if needed.
Only use attachments/accessories specified by the
manufacturer.
4
BEFORE INSTALLATION
* Do not use the product for purposes other than mounting a display on the wall.
* When installing/using the wall mount, be cautious of product damage and avoid accidents.
* If you have not fully read and understood the installation manual, do not install the product and contact the
dealer to have a specialized installer install the product for you.
* Install the product only on a vertical wall.
The manufacturer is not responsible for issue from installing the product on an angled wall or on the ceiling.
* Check that the accessories provided with the product are all included before installing. LG Electronics is not
liable for any damage or loss of accessories after the package has been opened.
* Keep the included accessories out of reach of babies or children as it can cause safety issues including
suffocation from swallowing the parts.
* Make sure screws are tight against the wall, but do not overtighten.
Applying excessive force to screws may damage to the wall, affect the product performance, or cause the
product to become damaged.
* Be careful not to install a TV that exceeds the weight restrictions of the wall mount.
* Be careful with the tools used during installation to prevent accidents or damage.
- Tools you will need - Phillips head + driver (manual or motorized) / Ø 4 mm drill bit for wood or steel / Level
/ Stud finder / Drill.
You may also need an 8 mm socket wrench or an Ø 8 mm drill bit for concrete.
INSTALLATION METHOD
- The actual product may differ from the picture.
1
How to Attach the Spacers to the Hanger
Hanger
Spacer (back)
Spacer (front)
→ Attach the spacers to
the hanger in the
direction of the
dotted lines as
shown in the
illustration.
5
ENGLISH
2
How to Attach the Brackets for the Product to the TV
- If the screws are not fully tightened when you fix the top and the bottom wall mount, check the length of the
screws and tighten them again.
- Always install the display with 2 or more people.
VESA Screw
- Work procedure
1. Remove the two VESA screws from upper
back of TV when in an upright position.
Screw for attaching the hanger
Hanger
2. Use the screws for attaching the hanger to
tighten the hanger as shown.
- Tighten the screws for attaching the
hanger and hanger until they are securely
attached to the TV set.
- Use the + driver (manual or motorized)
when tightening the screw.
Stand attaching screws
Stand
3. Remove the four stand attaching screws
tightened at the bottom of the TV set to
detach the stand.
- Place the TV on a table with the screen
facing up. Make sure that you place it on a
flat surface covered with a soft cloth or
cushion to protect TV set from scratches.
- The four stand attaching screws removed will
be used to attach the bottom wall mounts.
* CAUTION
- When detaching the stand, make sure to
hold it firmly while removing the screws.
Otherwise, it may fall.
Stand attaching screws
Bottom wall mount
4. Use the four stand attaching screws to
tighten the bottom wall mount as shown.
- Tighten the stand attaching screws and
bottom wall mount until they are securely
attached to the TV set.
- Use the + driver (manual or motorized)
when tightening the screw.
6
3
How to attach to masonry walls
Please follow the below direction.
- Check the material of the wall and the thickness of the finishing.
- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone
masonry brick and hallow block that do not crack.
- Do not mount the device on the walls made from plasterboard or medium density fiberboard (MDF). In this
case, the anchor and screws must be inserted into the concrete behind the finish surface. If there is no
concrete on the other side, then you must first install a separate hanger to securely install the anchors and
screws.
- When installing the product on wall material not designated, install the product so that each location can
withstand the pull out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
a
b
d e
Wall mount screw
c
Anchor
- Use the Ø 8 mm drill bit for concrete and hammer (impact) drill.
a. Use a drill bit Ø 8 mm to drill a hole for the anchor location within a depth of 80 mm - 100 mm
b. Clean the drilled hole.
c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to
face upward.
e. Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at Torque of 45 kgf/cm - 60 kgf/cm.
7
ENGLISH
4
How to Install the Top Wall Mount
Top wall mount cover
→ Open the top wall mount cover completely.
→ Place the top wall mount onto the area of the wall where you want to install it, and then check if the wall
mount is level using a leveler.
Wall mount screw
Top wall mount cover
→ Attach wall mount screws as shown in the illustration.
→ At this time, use a + driver (manual or motorized) or 8 mm wrench to tighten the screw so that the wall,
wall bracket and screw are completely pressed against one another.
→ After attaching the screws, put down the top wall mount cover.
8
5
How to Install the Bottom Wall Mount
How to Select the Installation Location of the Bottom Wall Mount
[unit : mm]
Product
packaging box
Product packaging box
➊
➋
➍
➌
➊ Place the box on the bottom center of the attached top wall mount and place the box at a right angle
(90 degrees) to the top wall mount as shown in the figure.
➋ Find the V on the bottom of your box, and mark the point facing it on the wall [(a) in the figure].
➌ Rotate the box 90 degrees counterclockwise, making sure that (a) point in the figure is always at the
center.
Find the H on the left side of your box and mark the point facing it on the wall.
➍ Move the box to the right horizontally to bring the mark on the wall (a) level with the H on the box. Check
if the box is level, using a level.
Find the V on the right side of your box, and mark the point facing it on the wall.
→ Install the bottom wall fixing brackets at the points marked in step
➌
and
➍
.
How to Install the Bottom Wall Mount
Wall mount screw
Bottom wall attaching
brackets
Washer
➌
➍
→ Fix the two bottom wall mounting brackets onto the wall using the wall mount screw as shown in the
figure.
→ Depending on the condition of the wall, use additional washers when tightening the bottom wall attaching
brackets.
9
ENGLISH
6
How to Attach the Top Wall Mount to the Product
- Two or more people are needed to lift and install the product.
➊
➋
Hang the hanger on the top wall mount as shown in the figure.
→ Two people must lift the TV set attached to the hanger and carefully check from both sides whether it is
properly installed.
→ Make sure that the product is fixed securely by lightly pulling on the bottom of the TV.
→ The product should be about 10 mm apart from the wall. When connecting cables and accessories, make
sure that the product is installed at a sufficient distance from the wall to avoid putting stress on them.
→ Pushing the product with excessive force may cause damage to the product.
Please follow the below direction.
This product is easily damaged by external shock, so please handle it with care. For more information,
please refer to the owner's manual of the TV.
7
How to Install the Top Wall Mount Fixing Pin
Pin for fixing top
wall mount
→ After installing the top wall mount, attach the wall mount to the TV using the top wall mount attaching pin as
shown in the illustration.
* CAUTION - If the wall mount is not attached to the TV using the top wall mount fixing pin, the TV may be
removed resulting in damage or injury.
10
8
How to Adjust the Level of the Product
If the product is not level after installation, lift the product slightly so that it moves to a position where it is
level.
Lifting Point
Adjust the horizontal levels
of the TV set by rotating it
centered in the top wall
mount.
Lifting Point
9
How to Tidy Up Cables
- Tidy up cables as shown in the illustration. Purchase a band for tidying up cables or use the band that
comes with the TV.
11
ENGLISH
PRODUCT SPECIFICATION
[ unit : mm ]
Hanger
Top wall mount
Bottom wall mount
Top Assembly Hanger Assembly Lower Assembly
Width (mm) 160 238 169.9
Height (mm) 40 99 34.9
Depth (mm) 18.5 18.5 49.6
Weight (kg) 1.1
Max.UL Load Capacity (kg) 30
The model and serial number of the product is located on
the back or one side of the product. Record it below
should you ever need service.
MODEL
SERIAL
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
