Page is loading ...
Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
Please read all instructions before you begin.
Shut off the water supply.
Observe all local plumbing and building codes.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Screwdrivers
Hex
Wrenches
110424-2-AC 2 Kohler Co.
1. Installing the K-258 and K-260 Handles
IMPORTANT! Risk of product damage. To avoid damaging the
ceramic cap, do not overtighten the flathead screw.
If replacing the ceramic trim, loosen the setscrew and pull the
handle off the stem extension.
Remove the stem extension.
Insert a wide-bladed screwdriver into the slot on the bonnet nut
and turn counterclockwise to loosen.
Remove the bonnet nut and ceramic bell.
For new and replacement installations, place a new ceramic bell
over the bonnet and secure with a bonnet nut. Insert a
wide-bladed screwdriver into the slot on the bonnet nut and turn
it clockwise to tighten.
Place a ceramic cap into the oval handle and secure it from
underneath with a flathead screw.
Align the handle assembly on the stem extension and secure with
a setscrew.
Repeat with the second handle if needed.
Bonnet
Stem
Extension
Ceramic
Bell
Ceramic
Cap
Oval
Handle
Bonnet
Nut
Flathead
Screw
Setscrew
Bonnet
Stem
Extension
Ceramic
Bell
Ceramic
Cap
Oval
Handle
Bonnet
Nut
Flathead
Screw
Setscrew
Kohler Co. 3 110424-2-AC
2. Installing the K-262 Handle
IMPORTANT! Risk of product damage. To avoid damaging the
ceramic cap, do not overtighten the flathead screw.
If replacing the ceramic trim, loosen the setscrew and pull the
handle off the stem extension.
Loosen the oval-head screw and remove the bonnet, washer and
spring.
Loosen the dog-point screws and remove the mounting plate.
Remove the ceramic ring.
For new and replacement installations, place a ceramic ring over
the valve.
Secure with a mounting plate and two dog-point screws.
Place the spring, washer, and bonnet over the valve.
Secure the bonnet onto the valve with the oval-head screw.
Place the ceramic cap into the oval handle and secure from
underneath with a flathead screw.
Align and place the handle assembly onto the bonnet. Secure
with the setscrew.
Ceramic
Ring
Ceramic
Cap
Mounting
Plate
Dog-Point
Screws
Oval-Head
Screws
Oval
Handle
Bonnet
Spring
Washer
Setscrew
110424-2-AC 4 Kohler Co.
3. Installing the K-264 Handles
IMPORTANT! Risk of product damage. To avoid damaging the
ceramic caps, do not overtighten the flathead screws.
If replacing the ceramic trim, loosen the setscrew(s) and pull the
handle off the bonnet.
For new and replacement installations, place the ceramic cap into
the oval handle, and secure from underneath with a flathead
screw.
Align and place the handle assembly onto the bonnet and secure
with a setscrew.
Setscrew
Bonnet
Oval Handle
Ceramic
Cap
Flathead
Screw
Kohler Co. 5 110424-2-AC
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
