Kohler 258-PH-96 Installation guide

Page is loading ...

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Please read all instructions before you begin.

Shut off the water supply.

Observe all local plumbing and building codes.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Screwdrivers

Hex

Wrenches

110424-2-AC 2 Kohler Co.

1. Installing the K-258 and K-260 Handles

IMPORTANT! Risk of product damage. To avoid damaging the

ceramic cap, do not overtighten the ﬂathead screw.

If replacing the ceramic trim, loosen the setscrew and pull the

handle off the stem extension.

Remove the stem extension.

Insert a wide-bladed screwdriver into the slot on the bonnet nut

and turn counterclockwise to loosen.

Remove the bonnet nut and ceramic bell.

For new and replacement installations, place a new ceramic bell

over the bonnet and secure with a bonnet nut. Insert a

wide-bladed screwdriver into the slot on the bonnet nut and turn

it clockwise to tighten.

Place a ceramic cap into the oval handle and secure it from

underneath with a ﬂathead screw.

Align the handle assembly on the stem extension and secure with

a setscrew.

Repeat with the second handle if needed.

Bonnet

Stem

Extension

Ceramic

Bell

Ceramic

Cap

Oval

Handle

Bonnet

Nut

Flathead

Screw

Setscrew

Bonnet

Stem

Extension

Ceramic

Bell

Ceramic

Cap

Oval

Handle

Bonnet

Nut

Flathead

Screw

Setscrew

Kohler Co. 3 110424-2-AC

2. Installing the K-262 Handle

IMPORTANT! Risk of product damage. To avoid damaging the

ceramic cap, do not overtighten the ﬂathead screw.

If replacing the ceramic trim, loosen the setscrew and pull the

handle off the stem extension.

Loosen the oval-head screw and remove the bonnet, washer and

spring.

Loosen the dog-point screws and remove the mounting plate.

Remove the ceramic ring.

For new and replacement installations, place a ceramic ring over

the valve.

Secure with a mounting plate and two dog-point screws.

Place the spring, washer, and bonnet over the valve.

Secure the bonnet onto the valve with the oval-head screw.

Place the ceramic cap into the oval handle and secure from

underneath with a ﬂathead screw.

Align and place the handle assembly onto the bonnet. Secure

with the setscrew.

Ceramic

Ring

Ceramic

Cap

Mounting

Plate

Dog-Point

Screws

Oval-Head

Screws

Oval

Handle

Bonnet

Spring

Washer

Setscrew

110424-2-AC 4 Kohler Co.

3. Installing the K-264 Handles

IMPORTANT! Risk of product damage. To avoid damaging the

ceramic caps, do not overtighten the ﬂathead screws.

If replacing the ceramic trim, loosen the setscrew(s) and pull the

handle off the bonnet.

For new and replacement installations, place the ceramic cap into

the oval handle, and secure from underneath with a ﬂathead

screw.

Align and place the handle assembly onto the bonnet and secure

with a setscrew.

Setscrew

Bonnet

Oval Handle

Ceramic

Cap

Flathead

Screw

Kohler Co. 5 110424-2-AC

Page is loading ...

Kohler 258-PH-96 Installation guide

Kohler 258-PH-96 Installation guide

in other languages

Related papers

Other documents