2. GLAWNING
  3. 45 Degree Tent Stove Flashing Kit
45 Degree Tent Stove Flashing Kit

GLAWNING 45 Degree Tent Stove Flashing Kit Operating instructions

  • Hello! I have reviewed the user manual for the GLAWNING VISTA stove. This document covers important fire safety instructions, including ventilation requirements, the need for a heat-resistant base, and the use of a carbon monoxide alarm. It also provides instructions on setting up the flashing kit and conducting the first burn. I'm ready to answer your questions about the safe use and installation of your stove.
  • Can I place the fire directly on the tent groundsheet?
    Is the flashing kit installation reversible?
    What should I do before using the stove for the first time?
FIRE SAFETY INSTRUCTIONS
VERY IMPORTANT PLEASE READ CAREFULLY BEFORE
USING YOUR STOVE FOR THE FIRST TIME
• e re should not be placed directly on the tent groundsheet because it will
get very hot - always place on a suitable heat-resistant base.
• Always ensure that the glawning has adequate ventilation and that the re
is properly ued out through the ashing kit (see overleaf). Be careful when
handling the ue kit as the edges can be sharp.
• If the doors of the glawning are closed then some of the half moon ventilation
aps should be le open to ventilate the glawning.
• Inadequate ventilation and ue set up can lead to death by carbon monoxide
poisoning. A carbon monoxide alarm should be used (and checked regularly)
as a precautionary measure, although it should not be relied on completely as
they do not work properly in all conditions.
• e re should be fully extinguished before going to sleep.
• Never leave the re unattended.
• Ensure that you have an adequate and easily accessible means of extinguishing
the re in an emergency. We would recommend keeping a small re extin-
guisher, a heat proof glove and a re blanket in the glawning.
• e re, re base and chimney will all get very hot - please ensure that animals
and children are supervised at all times and are not allowed near the re.
• e re should not be burned too hot so do not overload it with fuel.
• Due to the lightweight ue kit, this stove should not be used in very windy
weather.
Glamorous Awnings & Accessories
STEP 1 - For a VISTA stove you’ll
need to cut the silicone by a
small amount to fit the larger flue
(just enough to provide a cor-
rect but snug fit - around 10mm)
STEP 5 - using a screwdriver, make
a hole large enough for each of the
screws to go through.
STEP 6 - Screw on the flasing kit with
one metal plate on each side of the
tent. It can be le in place foreever
once installed.
STEP 7 - Push the flue through the
flashing kit and connect it to the
stove, making sure everything’s
straight.
STEP 8 - Sit back, relax and enjoy!
STEP 2 - Decide where you want the
stove (see guidance above) and place
the metal ring in the correct position
between the tent seams.
STEP 3 - With a pen, draw around the
INSIDE of the metal ring and mark
where each of the holes is.
STEP 4 - Carefully cut the hole in the
canvas
IMPORTANT
When deciding where to put your stove you should allow a distance of at
least 1 metre between the top of the stove and the lowest point of the canvas
through which the flue is inserted.
See diagram to the right
FITTING YOUR FLASHING KIT
1 metre
minimum
WATCH THE STOVE FITTING INSTRUCTION VIDEO ON OUR YOUTUBE CHANNEL.
PLEASE NOTE: BEFORE THE STOVE IS SET UP AND USED IN YOUR TENT IT IS RECOMMENDED
THAT THE FIRST BURN IS DONE OUTSIDE TO CURE THE PAINT. YOU SHOULD START WITH
A LOW FIRE USING JUST KINDLING.YOU WILL NOTICE WHAT LOOKS LIKE SMOKE COMING
FROM THE STOVE, ACCOMPANIED BY A STRONG SMELL. THIS IS NORMAL, CAUSED BY THE
STOVE PAINT CURING.
/